Hitachi Koki USA HV-F202SCL specifications Txclkout － Txclkout ＋

A

B

C

D

E

F

1		2	3	4
(b) Signal connection to DIGITAL OUT connector
Connector 1 (D.OUT1: 24bit / 30bit / 36bit)					A
	Pin No.	Signal	Pin No.	Signal
	1	GND	14	GND
	2	TXOUT 0 (－)	15	TXOUT 0 (＋)
	3	TXOUT 1 (－)	16	TXOUT 1 (＋)
	4	TXOUT 2 (－)	17	TXOUT 2 (＋)
	5	TXCLKOUT (－)	18	TXCLKOUT (＋)
	6	TXOUT 3 (－)	19	TXOUT 3 (＋)
	7	RX (＋) [ SERTC (＋) ]	20	RX (－) [ SERTC (－) ]
	8	TX (－) [ SERTFG (－) ]	21	TX (＋) [ SERTFG (＋) ]
	9	TRIG/VD (－) [ CC1 (－) ]	22	TRIG/VD (＋) [ CC1 (＋) ]	B
		＋		－
	10	N.U. [ CC2 ( ) ]	23	N.U. [ CC2 ( ) ]
	11	N.U. [ CC3 (－) ]	24	N.U. [ CC3 (＋) ]
	12	N.U. [ CC4 (＋) ]	25	N.U. [ CC4 (－) ]
	13	GND	26	GND
Connector 2 (D.OUT2: 30bit / 36bit)
	Pin No.	Signal	Pin No.	Signal
	1	GND	14	GND
	2	TYOUT 0 (－)	15	TYOUT 0 (＋)
	3	TYOUT 1 (－)	16	TYOUT 1 (＋)	C
	4	TYOUT 2 (－)	17	TYOUT 2 (＋)
	5	TYCLKOUT (－)	18	TYCLKOUT (＋)
	6	TYOUT 3 (－)	19	TYOUT 3 (＋)
	7	N.U.	20	N.U.
	8	N.U.	21	N.U.
	9	N.U.	22	N.U.
	10	N.U.	23	N.U.
	11	N.U.	24	N.U.
	12	N.U.	25	N.U.
	13	GND	26	GND	D
Connector (camera side) Sumitomo 3M 1226-1100-00PL or equivalent
N.U.: Not used
- D.OUT2 is used for Medium configuration.
- The digital out cable should be comprised of a twisted pair of wires having 100 ohm
characteristic impedance and an outer sheath shield type conductor.
- Connect the shield (ground) of the digital out cable to the ground terminal of the video
equipment, frame grabber, etc.					E
- Install clamp filter (ZCAT2035-0930A: TDK) at both ends (camera and video processor ends) in
the CE marking region.
- TX: Transmit data from camera to PC
- RX: Transmit data from PC to camera

(Note) Please do not unplug and insert cable (digital out cable) with a power supplied to a camera.

F

		DWG.No.	E400234503			8
						SHEET
							17
1	2		3		4
				DF022-4PE-S1