Hand Held Products 3900, 3800 manual Good Read Delay, Trigger Mode

Page 46

Good Read Delay

This sets the minimum amount of time before the scanner can read another bar code. Default = No Delay.

*No Delay

Short Delay

Medium Delay

Long Delay

Trigger Mode

Manual/Serial Trigger: You can activate the scanner either by pressing the trigger, or using a serial trigger command (see "Trigger Commands" on page 12- 4). When in manual trigger mode, the scanner scans until a bar code is read, or until the trigger is released.

When in serial mode, the scanner scans until a bar code has been read or until the deactivate command is sent. In serial mode, the scanner can also be set to turn itself off after a specified time has elapsed (see Serial Trigger Time Out, which follows). Default for 3800.

Manual/Serial Trigger

3 - 4

3800/3900 User’s Guide

Page 45 Page 47
Image 46
Page 45 Page 47
Contents User’s Guide Disclaimer FCC Class B Compliance Statement Statement of Agency ComplianceCanadian Notice TÜV Statement LED Safety StatementUL and cUL Statement TIC StatementTable of Contents Output Data Formatting Code 93 Message Length Check Digit Addenda Addenda Required Addenda Separator Cloning Maintenance Viii Typical Applications for Getting StartedAbout This Manual Unpacking the Scanner Or anScanner Identification Scanner Bottom ViewConnecting the Scanner When Powered by Host Keyboard Wedge For Plug and Play Mounting InformationSpecular Zone Option Setting IBM 4683 Ports 5B, 9B, and 17 Interface Symbology Suffix USB Interface3800/3900 User’s Guide Ocia Interface Symbology PrefixNCR Ocia Short Format 8 Bit Interface Nixdorf Ocia Interface SymbologyNCR Ocia Long Format 9 Bit Interface Serial Wedge3800/3900 User’s Guide 3800/3900 User’s Guide Terminal Interfaces Keyboard Wedge ConnectionTerminal ID Supported Terminals Terminal Models Terminal IDSupported Terminals Keyboard Style Keyboard CountryCountry Code Scan Keyboard Modifiers 3800/3900 User’s Guide Serial Port Connection Baud Rate RS-232 Word Length Data Bits, Stop Bits, and Parity RS-232 Word Length Data Bits, Stop Bits, and Parity RS-232 Handshaking Wand Emulation ConnectionWand Emulation Transmission Rate Wand Emulation Polarity Wand Emulation IdleDelay Between Blocks Data Block SizeOverall Checksum Output Beeper VolumeScan Rate Scan Voting Beeper ToneReduce Quiet Zone Reread Delay Good Read Delay Trigger ModeSerial Trigger Time Out 3800/3900 User’s Guide Prefix/Suffix Overview Scan the Add Prefix or Add Suffix symbolData Editing Points to Keep In MindTo Clear One or All Prefixes or Suffixes Scan the Clear One Prefix or Clear One Suffix symbolScan Add Suffix To Add a Carriage Return Suffix to all Symbologies Prefix Selections Suffix SelectionsHex Symbology Code Symbology ChartSymbology Code HexAscii Conversion Chart Code Dec Hex CharIntercharacter Delay Intercharacter, Interfunction, and Intermessage DelaysFunction Code Transmit User Specified Intercharacter Delay Interfunction Delay Intermessage Delay3800/3900 User’s Guide Data Format Editor Introduction Scan the Enter Data Format symbol Primary/Alternate FormatData Formatting To Add a Data FormatData Format Editor Commands Other Programming SelectionsMove Commands Data Format Editor Data Formatter Alternate Data Formats3800/3900 User’s Guide Secondary Code 39 Wand Emulation Secondary InterfaceSecondary RS-232 Connection Non Decoded Output Laser Emulation Transmission Rate Secondary Non Decoded Output Laser EmulationNon Decoded Output Laser Emulation Polarity Non Decoded Laser Emulation Idle Secondary Trigger ModeDisabling the Secondary Interface 3800/3900 User’s Guide All Symbologies SymbologiesIntroduction Message Length Description Codabar Start/Stop CharactersCheck Character Codabar Message Length ConcatenationCodabar Code Code 39 Message Length Code 39 Append BaseFull Ascii Interleaved 2 Check DigitInterleaved 2 of 5 Message Length Strict DecodingCode 93 Message Length Iata Code 2 Code 2Code 2 of 5 Message Length Matrix 2 Iata Code 2 of 5 Message LengthMatrix 2 of 5 Message Length Check Digits Required Code 11 Message Length GS Substitution Telepen Code 128 Message LengthTelepen Output Telepen Message LengthNumber System Addenda UPC aAddenda Required Addenda Separator UPC Strict DecodingUPC E0 and UPC E1 UPC E ExpandUPC E Addenda Addenda Separator EAN/JAN EAN/JAN Isbn Enable Default All EAN/JAN 8 Settings Addenda Addenda Separator MSI MSI Message Length Plessey Plessey Message LengthRSS-14 RSS LimitedRSS Expanded RSS Expanded Message LengthChina Post Code China Post Message LengthOff Minimum Message Length Maximum Message Length Scan Diagnostics Show GLI Blocks3800/3900 User’s Guide Minimum Message Length Maximum Message Length Enable UPC/EAN Version Eanucc Composite SymbologyEanucc Composite Eanucc Composite Code Message Length 3800/3900 User’s Guide Procedure Cloning3800/3900 User’s Guide Visual Menu Temporary Visual Menu ConfigurationInstalling Visual Menu from the Web Visual Menu IntroductionUpgrading USB Firmware Keyboard Function Relationships Interface KeysFunction Code HEX/ASCII Value Full Ascii Ctrl + Country Codes PS/2 Compatibles IBM XTs IBM, DDC, Memorex Interface Keys Supported Interface KeysIBM AT/XT Compatibles Telex, HarrisMemorex Telex SYN PF1 ETB PF2 Can PF3 PF4 SUB PF5 ESC PF6 PF7 PF8 PF9Esprit 200 Interface Keys Ansi AsciiSupported Interface Keys Apple Mac/iMac Show Software Revision To Add a Test Code I.D. Prefix to All SymbologiesUtilities Show Data FormatSpecular Effect Reduction Menu Command Syntax Serial Programming CommandsConventions Concatenation of Multiple Commands Query CommandsResponses Examples of Query Commands Trigger Commands Resetting the Factory SettingsMenu Commands Setting Serial Selection CommandWNDPAT0 Output Selections Prefix/Suffix Selections Data Formatter SelectionsSymbologies SelectionsCBRSSX0 I25STR0 Teldft UPAARQ0 UPAARQ1 E13ARQ0 Plsdft Mpddft Product Specifications Product SpecificationsParameter Specification Product Specifications Cable Pinouts StandardLaser CompatiblePinouts Standard CableWandEmulation Pinouts Primary Interface Cables Serial Output Standard CableStandard Cable Pinouts USB3800/3900 User’s Guide Cleaning the Scanner’s Window MaintenanceMaintenance Inspecting Cords and ConnectorsReplacing the Interface Cable TroubleshootingTo Replace the Interface Cable Is the scanner having trouble reading your symbols? 3800/3900 User’s Guide Product Service and Repair Customer SupportAsia Pacific Online Product Service and Repair AssistanceTechnical Assistance JapanOnline Technical Assistance Limited Warranty 3800/3900 User’s Guide 3800/3900 User’s Guide Page Page Page Sample Symbols Matrix 2 Programming Chart Save Discard Hand Held Products, Inc
Related manuals
Manual 20 pages 180 b
Top Page Image Contents