Dell C510, C610 manual Removing the 14.1-Inch Display Panel, Display-Feed Flex Cable Connections

Page 23

Display Assembly, Display Latch, and Hinge Covers: Dell Latitude C610/C510 Service Manual

batteries.

NOTICE: To avoid ESD, ground yourself by using a wrist grounding strap or by touching an unpainted metal surface on the computer.

NOTICE: Read "Preparing to Work Inside the Computer" before performing the following procedure.

1.Remove the hard drive.

2.Remove the display assembly.

3.Use a plastic scribe to pry the six rubber screw covers out of the screw holes located on the front of the bezel.

4.Remove the six M2.5 x 5-mm screws located on the front of the bezel.

NOTICE: Carefully separate the bezel from the top cover to avoid damage to the bezel.

5.Starting at the bottom of the display panel (by the Dell™ logo), use your fingers to separate the bezel from the top cover by lifting up the inside of the bezel while pushing in on the outside.

Removing the 14.1-Inch Display Panel

NOTICE: Disconnect the computer and any attached devices from electrical outlets, and remove any installed batteries.

NOTICE: To avoid ESD, ground yourself by using a wrist grounding strap or by touching an unpainted metal surface on the computer.

NOTICE: Read "Preparing to Work Inside the Computer" before performing the following procedure.

1.Remove the hard drive.

2.Remove the display assembly.

3.Remove the display bezel.

4.Remove the hinge covers.

5.Remove the two M2 x 4-mm screws on the left side of the display panel and the two M2 x 4-mm screws on the right side of the display panel.

NOTE: If you have a Hitachi display panel, remove the two M2 x 4-mm screws from the center of the left side of the display panel.

6.Remove the M2 x 4-mm screw that secures the display-feed flex cable to the display assembly through the black plastic flex-cable retention bracket (see "14.1-Inch Display Bezel and Panel").

7.Lift from the top and rotate the display panel out of the top cover.

8.Disconnect the bottom flex cable connector from the inverter connector by pulling straight up on the attached pull tab (see "Display-Feed Flex Cable Connections").

Display-Feed Flex Cable Connections

file:///C/Work%20Area%20-%20A/E%20DOC%20Posting/latc610/service%20manual/display.htm[2/1/2013 11:00:46 AM]

Image 23
Contents January 2002 Rev. A01 Recommended Tools Before You BeginPreparing to Work Inside the Computer Back Right Front 4 left Screw IdentificationComputer Orientation Screw IdentificationBottom Case Each 1 each Each 3 each Hard Drive Door Keyboard to EachDisplay Bezel Back to Contents Keyboard Display assembly Bottom case Center control coverSystem Components Exploded ViewFan guard Bottom of computer M3 x 5-mm screw 3 hard drive door Hard DriveRemoving the Hard Drive Hard Drive RemovalReplacing the Hard Drive Memory Module Cover Memory Modules, Mini PCI Card, and ModemMemory Modules Removing the Memory Module CoverMemory Module Removal Removing the Memory ModulesReplacing the Memory Modules Mini PCI Card Mini PCI CardRemoving the Mini PCI Card Removing the Modem Antenna connectors on card 2 2 antenna cablesModem Replacing the Mini PCI CardModem Removal M2 x 3-mm screws Modem connector Modem cable 4 pull tabReplacing the Modem Page Screw Removal KeyboardRemoving the Keyboard Keyboard Removal Center Control Cover RemovalReplacing the Keyboard Keyboard Connector RemovalBack to Contents Display Assembly Display Assembly, Display Latch, and Hinge CoversDisplay Assembly Remove the center control cover Display-Feed Flex Cable ConnectorTop cover Display panel Removing the 14.1-Inch Display BezelInch Display Bezel and Panel Batteries Remove the hard drive Removing the 14.1-Inch Display PanelDisplay-Feed Flex Cable Connections Replacing the 14.1-Inch Display Panel Display Latch Removal 14.1-Inch XGA Panel Shown Display LatchRemoving the Display Latch Replacing the Display LatchReplacing the Hinge Covers Hinge Cover ReplacementHinge Covers Removing the Hinge CoversRight hinge cover 2 left hinge cover Remove the hard drive Remove the keyboard Palm RestRemoving the Palm Rest Palm Rest Screw RemovalPalm Rest Removal Back to Contents Microprocessor thermal cooling assembly 2 captive screws Microprocessor Thermal Cooling AssemblyRemoving the Microprocessor Thermal Cooling Assembly Microprocessor Thermal Cooling Assembly RemovalReplacing the Microprocessor Thermal Cooling Assembly Microprocessor Module Removal Microprocessor ModuleRemoving the Microprocessor Module Replacing the Microprocessor Module Remove the microprocessor thermal cooling assemblyRemove the palm rest Hybrid Cooling FanRemoving the Hybrid Cooling Fan Hybrid Cooling Fan RemovalM2 x 3-mm screw Reserve battery Speaker connector Reserve BatteryRemoving the Reserve Battery Reserve Battery RemovalSystem board connector 4 reserve battery cable Replacing the Reserve BatteryFlashing the Bios Flashing the BiosRouting the Left Speaker Cable Speaker Orientation Speaker AssembliesRemoving the Speaker Assemblies Speaker Assemblies Antenna cable In-line connector Replacing the Speaker Assemblies System Board Screw Removal System BoardRemoving the System Board M2.5 x -mm screw System Board RemovalReplacing the System Board Battery and Module Bay Latches Battery and Module Bay LatchesRemoving the Battery and Module Bay Latches Replacing the Battery and Module Bay Latches Data Pin Assignments for I/O ConnectorsUSB Connector Serial Connector18-23 Parallel ConnectorVideo Connector Video TV-Out Connector PS/2 ConnectorDocking Connector 124 121122 123164 161162 163Back to Contents
Related manuals
Manual 138 pages 13.75 Kb