Cognitive Solutions B780, A776 manual Configure Scan Options, Configure Max Scan Width & Height

Page 156

144 Chapter 6: DH emulation

Configure Scan Options

Hexadecimal: 1D C6 m n

Parameters:

m

n

Description

 

 

 

0

-

Configure Imager default settings. Parameter n is ignored.

 

 

 

1

0

Disable auto eject on top scan jam (default).

1

1

Enable auto eject on top scan jam.

2

n

Set maximum tag storage memory to n Kbytes. Default 4K. Range 2K to 64K. Out of range

 

 

parameter defaults to 4K.

Return: None

Description: Configures scan options. Parameter m>2 reserved for future options This setting is retained across power cycles.

Configure Max Scan Width & Height

Hexadecimal: 1D C7 wL wH lenL lenH

Parameters: wL wH is the maximum width of a scan in pixels (<= physical maximum 832); lenL lenH is the maximum length in pixels (<= 2284 ~ 11.25”). The width should be values evenly divisible by 4 value will be truncated by zeroing out the lowest-most 2 bits.

Return: None

Description: This sets the maximum values for all scanned documents to within ½ mm (4 pixels). As the imager must be prepared for a maximum size, this allows the firmware to use optimum buffers and thus provide for retaining more image slots in a circular buffer arrangement.

This setting is retained across power cycles.

Transmit Printer Type (Extended Existing Command)

Hexadecimal: 1D 49 02

Parameters: None

Return: M a single byte, as specified in existing commands, with its undefined bit #5 now used to indicate imager installed. 0= not present (existing definition), 1= imager present (new)

Description: This is an additional definition that uses a previously undefined bit to tell applications whether or not an imager is present.

A776 (B780) Programming Guide

A776-PG00001 C 12/09

Page 155 Page 157
Image 156
Page 155 Page 157
Contents Programming Guide Printer without Imaging Printer with ImagingPage Contents Contents A776 Configurable Slip Commands B780 Configuration CommandsBar codes Mode Macros Micr check reader commands User data storageContents Print and paper feed Convert 6-dots/mm bitmap to 8-dots/mm bitmap 100 106113 114121 126129 132140 142143 144152 153154 156Contents How to use this Guide Where to find the basicsWhere to find advanced technical information SupportAbout this Guide Startup Diagnostics Runtime diagnosticsRemote diagnostics Printer Status, Ethernet and IndicatorsEthernet terms and default setup Ethernet TerminologyEthernet Default Setup     Indicators Indicator Sequence ConditionGreen slip-in light in front of the paper feed button For more information about See this sectionMigrating from existing CognitiveTPG printers A758 wide slip station 66 columnsA760 wide slip station 66 columns Command Description Difference between the A756 A776 24 n1 n2Moving from the A756 to the A776 Emulation commands NL nHA776 Emulation Commands A776 Configuration CommandsSelect A776 Narrow Slip 51-column Compressed Print Option Select A776 Delete Slip Trailing Spaces OptionSelect A776 21 and 25-line Rotated Slip Print Options Select Cover Open OptionSet Page Mode Margin Mechanical Adjustment Set Page Mode Option to Trim Full DotsSelect A776 Slip Eject Option Select 45/60 Column Slip OptionA776 Slip Character Spacing A776 Slip Minimum UnitsA776 Slip Left Margin and Print Width A776 Slip Print JustificationMoving from A756/A758 to A776 Two-color Commands AsciiLogoEZ colorization commands DiscriptionB780 Emulation Commands B780 Configuration CommandsMigrating from the A721 7221 printer to the B780 Select DH Pitch and Rotated Text Columns Select Slip Right Margin in Page Mode Select Two Sensor Option for B780Select Number of Lines of Validation for B780 Select B780 Map User Character Option for B780Select B780 Map Logo Option for B780 Select Cover Open Option for B780Select Concurrent Print to Receipt for B780 Select B780 with A776 Slip FunctionsSet Page Mode Option to Trim Full Dots Migrating to a new printer Overview of Printing Characteristics Programming the Printer 23Receipt character specification Character appearanceRotated Scaled Shading StandardPrint zones Print zones for receipt station 80 mm paperProgramming the Printer 25 1B 64 n command, with n = Print zones for slip stationPrint Zones for Slip, Validation Lines InchesProgramming the Printer 27 Rotated printing commands Commands listed by function Commands in bold are ColorPOS commandsPrinter actions Text characteristics Print and paper feedVertical and horizontal positioning Graphics  31Batch mode Unsolicited status mode Code hexadecimal CommandStatus Real-timeMicr check reader commands Bar codesMode MacrosEthernet setup commands User data storageFlash download 1D 97 m n User storage statusImage Commands Programming commands 35Command conventions Command descriptionsClear printer Close form Open formPerform partial knife cut Generate toneSelect peripheral device for multi-drop Selects the device to which the host computer sends dataInitialize printer Set slip paper eject lengthSelect receipt or slip for setting line spacing This command is ignored if n is out of rangeSelect paper sensors to output paper end signals Programming commands 39Enable or disable panel button Default Bit of n FunctionSelect sensors to stop printing Set slip paper waiting timeGenerate pulse to open cash drawer Sends a pulse to open the cash drawerRelease Paper Set current colorAfter a power loss or reset the default value m=0 is reset Select cut mode and cut paperIf m is out of the specified range, the command is ignored Select slip stationProgramming commands 43 Select receipt stationSet Interpretation of Set current color Hexadecimal 1E DecimalPrint test form Print and feed paper one linePrint and eject slip Print and carriage returnProgramming commands 45 Range of n DefaultFeed n dot rows Add n extra dot rowsPrint Print and feed paperPrint and reverse feed paper Print and feed n linesPrint and reverse feed n lines Reverse feed n linesReverse feed n dots Horizontal tabSet column Set absolute starting positionSet vertical line spacing to 1/6 inch Programming commands 49 Set vertical line spacingSet horizontal tab positions Value of kSet relative print position Compatibility information A776 receipt vs. A756 receiptProgramming commands 51 Select justificationSet left margin GS L nL nHDefault of y Set horizontal and vertical minimum motion unitsSet printing area width GS P x yText characteristics commands Select double-wide charactersSelect single-wide characters Select 90 degree counter-clockwise rotated printStandard mode the horizontal motion unit is used Select pitch column widthSelects the character pitch for a print line Set right-side character spacingSelect print mode Select or cancel user-defined character setCharacter sets cannot be used together on the same line Define user-defined character set Values and ranges ReceiptSlip s = Select or cancel underline mode This command is ignored if n is out of the specified rangeProgramming commands 57 Copy character set from ROM to RAMCancel user-defined character Select or cancel emphasized modeSelect double-strike Printer output is the same as in emphasized mode Cancel double-strikeSelect or cancel italic print Select international character setSelect or cancel 90 degree clockwise rotated print Select or cancel upside-down print modeCharacter sets cannot be mixed on the same line Select character code tableSelect or cancel white/black reverse print mode Character height selectionHex Decimal Height This command is only valid for the receipt station Reverse color text mode ColorPOSSet smoothing Text strike-through mode ColorPOS Select font ID numberCB hex Kanji CE hex Korean Select font style numberSave font ID number as default font at power up Download fontDownload font list Print downloaded font informationProgramming commands 65 Define extended user-defined character setSelect active user-defined character set Values and rangesSelect bit image mode Value of m Mode No. of dots vertical No. of dots horizontalDownload BMP logo Advanced raster graphics is not available in page mode Dot single-density N1 + 256 × n2Print advanced raster graphics Value of rSelect double-density graphics Print Flash LogoDefine Flash Logos XHxL 1024 max printable xHxL = 72 = 576 dots wide YHyLDefine downloaded bit image Print downloaded bit imagePrint raster monochrome graphics ColorPOS Print raster color graphics ColorPOSDownload logo image ColorPOS Max n1 =Monochrome shade mode ColorPOS Color shade mode ColorPOSProgramming commands 71 Merge watermark mode ColorPOS Logo print with color plane swap ColorPOSApply shading to logo ColorPOS Hexadecimal 1D 89 n m DecimalProgramming commands 73 Form and merge real-time surround graphic ColorPOSThis command is ignored in page mode Background logo print mode ColorPOSSave graphics buffer as logo ColorPOS Apply margin message mode ColorPOS Shade and store logo ColorPOSSee Print downloaded bit image command Logo print with knife cutSet temporary max target speed Decimal ValuesProgramming commands 77 Set LogoEZ colorization ColorPOSExample Value of f= 3 link margin message printing Modify the settings within the utility Programming commands 79LogoEZ utility default settings Set LogoEZ attribute mapping ColorPOSProgramming commands Original attribute mapped table Attributes substituted table Bit onEnable constant speed logos Programming commands 81 Related informationConvert 6-dots/mm bitmap to 8-dots/mm bitmap Status command introduction Transmit peripheral device statusHexadecimal 1B 75 Decimal Value of returned byte BitProgramming commands 83 Transmit paper sensor statusTransmit printer ID ESCPrinter ID Specification ID Hexadecimal Transmits the printer ID specified by n as follows= 4 Logo Definition Bit Off/On Hex Decimal Function Transmit printer ID, remote diagnostics extension Preforms the remote diagnostic function specified by nProgramming commands 85 GS I @ nProgramming commands Value of n Hex Dec Remote diagnostic item FunctionProgramming commands 87 Transmit statusA776 B780 Programming Guide Real-time commands Send printer software versionRules for using real-time commands Preferred implementationAlternate implementation Moving data through the bufferBusy line and fault conditions Programming commands 91Real-time status transmission = Transmit error status Bit Status Hex Decimal Function A776 B780 Programming Guide Real-time request to printer Real-time commands disable Programming commands 95Real-time printer status transmission Unsolicited status mode Select or cancel unsolicited status mode USMSecond byte error information Bit Off/On Hex Decimal Status for USMThird byte paper sensor information Fourth byte paper sensor information -- A776Batch mode response Unsolicited status mode USMRecognizing data from the printer Real time responseSelect printing position of HRI characters Select pitch of HRI charactersSelect bar code height Print bar codeProgramming commands 101 Exceptions Bar codeLength Illegal data cancels this command Undercut, default 0, can be set 0 to a-1Programming commands Bar code Set GS1 DataBar formerly RSS parametersProgramming commands 103 Print GS1 DataBar formerly RSS, data length specifiedPrint GS1 DataBar formerly RSS, null terminated TypePrint multiple barcodes GS kSample symbol description Programming commands 105Defaults GS p a b c d e fRelated Information Value Dimension Row height Select bar code widthSets the bar code width to n dots Reset to power-on parameters SizeCharacter Size ExceptionsMode configurations Slip Page Mode ImprovedSlip Page Mode Enabled Slip Page Mode Disabled Print and return to standard modeSelect page mode Programming commands 109Select standard mode This command is effective only in page modeSelect print direction in page mode Set print area in page mode Programming commands 111Command is effective only in page mode Set absolute vertical print position in page modeSet relative vertical print position in page mode NL + nH × 256 × vertical or horizontal motion unit inchesSelect or cancel macro definition Contents of the macro can be defined up to 2048 bytesExecute macro Micr commands Programming commands FormulasRead Micr data and transmit Status Status byte valueMicr parsing Transmit last Micr readDefine parsing format, save in Nvram Define parsing format, do not save permanentlyError number One digit returned Status Two digits returnedField separator Country code One digit returnedSample parsing formats Programming commands ESC w p T ‘/ a ‘/ C ‘/ S CR Programming commands 119 Check serial numberLoading the exception table Which writes the two byte word n1n2 to word k in NvramException table entry format Bits within byteProgramming commands 121 Maintaining the exception tableWrite to user data storage Read from user data storage Read from non-volatile memoryWrite to non-volatile memory Nvram Select memory type SRAM/flashFlash memory user sectors allocation Expanded flash memory allocationMemory allocation sequence 22 80 31 nL nH Sectors to logo/font area 22 80 32 nL nHProgramming commands Values and ranges Erase user flash sectorValue of n = 49 Ascii n = 1 HEX Programming commands 125 = 50 Ascii n = 2 HEX User storage status ColorPOSDownload mode Hexadecimal 1B 5B 7D Decimal 27 91Return boot sector firmware part number Return segment number status of flash memoryMemory sector to download Get firmware CRCErase all flash contents except boot sector Return main program flash CRCErase selected flash sector Download to active flash sectorReset firmware Restore default settingsSet IP address Set Net MaskDefault enabled Set GatewaySet raw Tcpip port Telnet DaemonDhcp auto-configuration Inactivity timeoutProgramming commands 131 Keep-alive pingsImaging Commands Calibrate ScannerHexadecimal ID B0 Parameters None Value DefinitionConfigure/Change Image Transmission Port Set Top Entry Startup DelaySet Image Format Properties Configure Binarization Methods and Attributes MethodDefine/Update Application Tag Values Programming commands 135Decimal Value Definition T6.G4 binary, else 1=Black is ZeroAttach Scan Application Tags Return Imager StatusHexadecimal 1D B6 Parameters None Hexadecimal 1D B7Real-Time Imager Status Value Definition Decimal MeaningHexadecimal 10 04 Parameters None Bit MeaningReal-Time Error Status Real-Time Cancel Image TransmissionWait for Scan & Optionally Transmit Hexadecimal 10 05 Parameters None Return NoneSensors currently covered none = 0 value Bit 0 =1 rear image sensor coveredBit 1 =1 front image sensor covered Bit 2 =1 image cover openTransmit Image LZW lossless, also used in GIF compressed grayscale TiffCcitt T.6 compression binary Tiff Reserved for Jpeg lossyProgramming commands 141 Bytes Scanned image Tiff structure lengthStructure containing the tags and images As in the Image Status Command return Eject from ScannerHexadecimal 1D BA p Free Image Free Imager BufferingGet Buffered Image List Get Buffered Image AttributesConfigure Scan Options Configure Max Scan Width & HeightTransmit Printer Type Extended Existing Command Hexadecimal 1D C6 m n Parameters DescriptionList of DH 4700 Emulation Commands Hexadecimal Code Command NameDH Emulation 145 List of DH emulation Commands Hexadecimal Code Command NameList of DH 4700 Command Descriptions Printer Function CommandsReset Printer Cash DrawerDocument Clamp Open Self TestClamp Delay Document Clamp CloseForm Eject DownloadPrint Characteristics Commands Print SpeedBuffered Validate Buffer ClearCharacter Set DH Emulation 151Underline Print Underline OffDouble-High Off Double-High FontGraphics Commands GraphicsGraphics 5 Dot DH Emulation 153Printer Status Commands Status 3 BitTransmitted status is shown in the table Status 6 BitDH Emulation 155 Commands listed by hexadecimal code Appendix a Commands by hexadecimal code157 34 m a0 a1 a2Appendix a Commands by hexadecimal code Code hexadecimal 159 Or …n160 Print raster color graphicsM n o Apply margin message mode X y o p q161 Appendix B Resident Character Sets Code Page 437 USCode page 737 Greek 163Code page 850 Multilingual Code Page 852 Slavic 165Code Page 857 Turkish Code page 858 with Eurosymbol 167Code page 860 Portugese Code page 862 Hebrew 169Code page 863 French Canadian Code page 865 Nordic 171Code page 866 Cyrillic Code page 1252 Windows Latin 173Page 1F 03 18 01 n Auto Journal Mode via Configuration Command Electronic Journal StorageThere are two methods for activating Electronic Journal Exception Conditions in Auto Journal Mode Journal RAM bufferJournal Flash buffer Printing and Erasing the Journal Flash Buffer Operator Activation of Journal Print and Erase1F 0A C3 Clear Journal 1F 0A C4 Print Journal1F 0A C5 Return Journal Status Returns one byte of status1F 0A C6 Return Journal Flash Size Journal flash Buffer usedPage A776-PG00001 Rev. C 12/09
Related manuals
Manual 2 pages 56.15 Kb Manual 2 pages 48.96 Kb

B780, A776 specifications

Cognitive Solutions A776 is an advanced technology platform designed to enhance decision-making processes through the application of artificial intelligence and cognitive computing. This state-of-the-art solution seamlessly integrates multiple technologies to optimize business operations and drive innovation across various sectors, including finance, healthcare, and manufacturing.

One of the main features of A776 is its robust data processing capabilities. Leveraging powerful machine learning algorithms, the platform can analyze vast amounts of data in real-time, identifying patterns and insights that would otherwise be overlooked. This enables organizations to make informed decisions based on actionable intelligence, significantly improving efficiency and productivity.

Another key characteristic of the A776 system is its natural language processing (NLP) capability. This feature allows the platform to understand and interpret human language, making it easier for users to interact with the system and obtain valuable insights. By integrating NLP, Cognitive Solutions A776 can provide intuitive user experiences, enabling workforce members to query data using everyday language rather than complex coding skills.

The A776 is also built on a flexible architecture that supports seamless integration with existing IT ecosystems. This interoperability allows organizations to harness their current data sources while taking advantage of the innovative features offered by A776. The platform’s API support enables smooth connections with third-party tools, enhancing collaboration and expanding its range of applications.

Security is a major focus of the Cognitive Solutions A776. The platform is equipped with advanced encryption protocols and compliance measures to ensure that sensitive data is protected against breaches and unauthorized access. This commitment to security helps businesses maintain customer trust and safeguard their competitive advantage.

Scalability is another defining feature of the A776. As businesses grow and evolve, the platform can be easily adapted to meet changing demands. Whether a small startup or a large enterprise, organizations can scale their cognitive solutions according to their operational needs.

Furthermore, the Cognitive Solutions A776 is designed with user accessibility in mind. The interface features customizable dashboards that provide a clear overview of insights and performance metrics, enabling users at all levels to harness the power of cognitive computing without requiring extensive training or technical expertise.

In conclusion, Cognitive Solutions A776 is a cutting-edge platform that offers a range of features, including advanced data processing, natural language processing, robust security measures, and user-friendly design. Its flexible architecture allows it to integrate seamlessly with existing systems, making it an indispensable tool for organizations looking to leverage artificial intelligence in their decision-making processes.
Top Page Image Contents