DFI PM12-EC, PM12-EL user manual Resume on Alarm, Date of Month, Resume Time hhmmss

Page 75

Award BIOS Setup Utility

When enabled, the system will power-on to respond to calls coming through an external or internal modem. Refer to “Wake-On-Ring Connector” in chapter 2 for more information.

Resume on Alarm

Enabled When Enabled, you can set the date and time you would like the Soft Power Down (Soft-Off) PC to power-on in the “Date (of Month)” and “Resume Time (hh:mm:ss)” fields. However, if the system is being accessed by incoming calls or the network prior to the date and time set in these fields, the system will give priority to the incoming calls or network.

Disabled Disables the automatic power-on function (default)

Date (of Month)

0The system will power-on everyday according to the time set in the “Resume Time (hh:mm:ss)” field.

1-31 Select a date you would like the system to power-on. The system will power-on on the set date, and time set in the “Resume Time (hh:mm:ss)” field.

Resume Time (hh:mm:ss)

This is used to set the time you would like the system to power-on. If you want the system to power-on everyday as set in the “Date (of Month)” field, the time set in this field must be later than the time of the RTC set in the Standard CMOS Features submenu.

3

75

Image 75 Contents
62500230 PM12-EC PM12-ELCopyright TrademarksAll Rights Reserved FCC and DOC Statement on Class B Mainboard Table of Contents Function Appendix B System Error MessagesAppendix C Troubleshooting Supported SoftwaresProcessor Features and SpecificationsFeatures ChipsetIntroduction Onboard Audio FeaturesOnboard LAN Features PM12-EL only Onboard Graphics FeaturesConnectors Rear Panel I/O Ports PC 99 color-coded connectorsDesktop Management Interface DMI PCI Bus Master IDE ControllerIrDA Interface USB PortsWake-On-LAN Dual Function Power ButtonIntroduction Intelligence Wake-On-RingRTC Timer to Power-on the System Wake-On-PS/2 Keyboard/MouseWake-On-USB Keyboard/Mouse Virus Protection AC Power Failure RecoveryPackage Checklist PM12-EC Mainboard LayoutSupports onboard LAN Hardware InstallationDDR System MemoryHardware Installation Installing the DIM Module JP1 Jumper Settings for Clearing Cmos DataHardware Installation Jumper Settings for Selecting the PS/2 Power PS/2 power selectOn VCC power Rear Panel I/O Ports Accordingly. Refer to for more information Hardware Installation 1 PS/2 Mouse and PS/2 Keyboard PortsJ11 PS/2 Mouse PS/2 KeyboardHardware Installation 2 RJ45 Fast-Ethernet Port PM12-EL only Hardware Installation Universal Serial Bus Ports USB 3 and USB J13Additional USB Ports USB 3 and USB Pin Function Hardware Installation Serial Ports Connecting the Serial PortsRate Hardware Installation Parallel PortStandard Parallel Port One direction only Allows parallel port to operateHardware Installation VGA Port VGA1VGA Port Hardware Installation 2.5.7 Game/MIDI Port CN301Game/MIDI Port Line-out Line-in Mic-in Front audio J21 Front Audio J21 Hardware Installation Audio JacksFront Audio J21 Onboard Audio JacksJ18 Pin I/O ConnectorsInternal Audio Connectors J19Hardware Installation 2.6.2 Floppy Disk Drive Connector Connecting the Floppy Disk Drive CableFDD J6 Connecting the IDE Disk Drive Cable Hardware Installation IDE Disk Drive ConnectorAdding a Second IDE Disk Drive IrDA J8 Hardware Installation IrDA ConnectorJ15 Hardware Installation 2.6.5 CPU Fan ConnectorJ14 Hardware Installation Chassis Fan ConnectorHardware Installation 2.6.7 Wake-On-LAN Connector Wake-On-LAN+5VSB Ground Wake-On-Ring Hardware Installation Wake-On-Ring ConnectorPCI Standby Power LED Hardware Installation 2.6.9 LEDsDimm Standby Power LED PCI Standby Dimm Standby Power LEDJ17 Hardware Installation Power ConnectorsATX Main Power Connector Pin Function 12V Ground +5V +12V +5V +12V Power Connector Pin Function GroundGround +5V Front panel Connectors J10 PWR-LED Power/Standby LED Standard Cmos Features When you press Del, the main menu screen will appearBasic Input/Output System Award Bios Setup Utility DateTime Capacity Access ModeIDE HDD Auto Detection IDE Primary Master/Slave and IDE Secondary Master/SlaveLanding Zone CylinderHead PrecompTotal Memory Halt OnBase Memory Extended MemoryVirus Warning Award Bios Setup Utility Advanced Bios FeaturesSwap Floppy Drive Quick Power On Self TestCPU L1 & L2 Cache CPU L2 Cache ECC CheckingTypematic Delay Msec Boot Up Floppy SeekBoot Up NumLock Status Typematic Rate SettingVideo Bios Shadow Security OptionOS Select for Dram 64MB Award Bios Setup Utility Advanced Chipset Features Dram Clock Dram Clock/Drive ControlCurrent FSB Frequency Current Dram FrequencyBank Interleave Dram Command RateDram Timing Sdram CAS LatencyAGP Driving Control AGP ModeAGP & P2P Bridge Control AGP Aperture SizeAGP Master 1 WS Write Select Enabled to support the AGP Fast Write functionAGP Driving Value AGP Fast WritePCI Master 0 WS Write PCI Delay TransactionCPU & PCI Bus Control CPU to PCI Write BufferVGA Share Memory Size System Bios CacheableMemory Hole Video RAM CacheableVIA OnChip IDE Device Award Bios Setup Utility Integrated PeripheralsIDE Prefetch Mode On-Chip IDE Channel 0 and On-Chip IDE ChannelIDE Primary Master/Slave PIO and IDE Secondary Master/Slave Onboard LAN PM12-EL only Onboard LAN Boot ROM PM12-EL onlyVIA OnChip PCI Device Onboard AC97 AudioSuper IO Device Onboard FDC ControllerOnboard Serial Port 1 and Onboard Serial Port Use IR Pins Uart Mode SelectIR Transmission Delay UR2 Duplex ModeGame Port Address Parallel Port ModeEPP Mode Select ECP Mode Use DMAUSB Keyboard Support IDE HDD Block ModeInit Display First OnChip USB ControllerAward Bios Setup Utility Power Management Setup Acpi FunctionAcpi Suspend Type Video Off Option Power Management Option HDD Power Down Suspend ModePWR Lost Resume State Run Vgabios if S3 ResumeModem Use IRQ Soft-Off by PwrbtnPS2KB Wakeup Select 5.12 IRQ/Event Activity DetectResume On LAN/Ring USB Resume from S3PCI Master Resume on PCI EventResume on Alarm Date of MonthResume Time hhmmss IRQ15 IRQs Activity MonitoringResources Controlled By Award Bios Setup Utility 6 PnP/PCI ConfigurationsPNP OS Installed Reset Configuration DataAssign IRQ for USB IRQ Resources6.5 PCI/VGA Palette Snoop Assign IRQ for VGAPCI Slot 1 Use IRQ to PCI Slot 3 Use IRQ Auto Detect PCI/DIMM Clk Award Bios Setup Utility Frequency/Voltage ControlCPU Clock Ratio This field is used to select the CPU’s frequency ratioCPU Clock Load Optimized Defaults Award Bios Setup Utility Load Fail-Safe DefaultsSet User Password Award Bios Setup Utility Set Supervisor PasswordExit Without Saving Award Bios Setup Utility Save & Exit SetupUpdating the Bios Award Bios Setup Utility Running the DMI Utility Desktop Management Interface DMIEdit DMI Supported Software Using the DMI UtilitySupported Software Add DMI Load DMI FileSave DMI File Supported Software Drivers, Utilities and Software ApplicationsVIA Service Pack Installation Notes Supported Software VIA Service PackSupported Software Supported Software 2 S3 ProSavage VGA Drivers Supported Software Realtek Audio Drivers Supported Software VIA LAN Drivers PM12-EL only Supported Software VIA USB 2.0 Drivers Supported Software 4.2.6 Microsoft DirectX Supported Software McAfee VirusScan Online Installation Notes Using the Suspend to RAM Function Appendix a Using the Suspend to RAM FunctionUsing the Suspend to RAM Function 102 103 Error Messages Cmos battery is no longer functional. It should be replacedPost Beep System Error Message Monitor/Display Troubleshooting ChecklistTroubleshooting Power SupplyFloppy Drive Hard disk failure Troubleshooting Hard DriveKeyboard Troubleshooting Serial Port