Keytec MCI Modules, Magnetic stripe reader MSR, Cable routing, Functional check

Page 5

3.2.4 PS/2 cable installation (with glidepad/microjoystick)

Installation must be carried out when the computer is switched off. If a keyboard and/or mouse is already connected to the computer, please remove it.

 

First, insert the violet 6-pin mini DIN plug (Figure 4) of the keyboard

 

cable into the keyboard socket provided on the computer (violet).

Fig. 4 PS/2 Y-cable

Ensure that the poles are correct (coding pin).

Then insert the green 6-pin mini DIN plug (Figure 4) of the pointing device into the PS/2 mouse socket provided on the computer (green). Ensure that the poles are correct (coding pin).

Never force the keyboard plug into the PS/2 socket on the computer. This could result in bending of the connection pins – danger of short circuits!

3.2.5 Cable installation for smart card read/write device (USB / RS 232)

To connect the USB model, proceed according to section 3.2.2 USB cable installation.

Installation of the serial model must be carried out when the computer is switched off. Insert the 9-pin Sub-D connector (Figure 5) into an unoccupied serial interface on your PC (COM 1 to COM 4).

Now restart your system. The SCR module is now automatically

detected. You can find further details regarding driver installation Fig. 5 SCR serial cable under http://www.preh-keytec.com.

3.2.6 Cable routing

 

 

When it is delivered, the connection cable is routed on the right

 

 

side (seen from above). If the cable outlet has to be moved to

 

Nips

the left or center, you can do this quite easily.

 

 

Lay the keyboard with the keypad facing down on a soft surface.

 

 

 

 

To move the cable outlet to the left, move the connection cable

 

 

as shown in Figure 6. Ensure that the keyboard cable is firmly

 

 

pressed into the nips provided.

Fig. 6

cable nips

 

3.2.7 Functional check

After you have started your computer, all four LEDs light up briefly. Then, depending on the status of the NumLock, CapsLock and ScrollLock, the associated LEDs light up. Your Preh Commander® MCI is now ready for use.

4 Modules

4.1 Magnetic stripe reader (MSR)

All magnetic cards according to ISO 7810 and 7811 can be read. The magnetic stripe reader records the entire information content of the magnetic card. A LED signal (green Accept LED) is issued after a successful read procedure.

The magnetic card can be swiped through the reading device in both directions (Figure 7). This provides easy manipulation for both right- and left-handers.

MCI_Manual_V13.doc

Page: 5 of 20

03555-120

Image 5
Contents Preh Commander MCI Table of Contents / Inhaltsverzeichnis / Sommaire Installation Characteristics of the MCI FamilyContents of package General Notes for the UserUSB cable installation Installation of the keyboard3 PS/2 cable installation without glidepad/microjoystick System requirementsModules 4 PS/2 cable installation with glidepad/microjoystickMagnetic stripe reader MSR Cable routingSmartcard read/write device SCR Keylock KLGlidepad Pointing devicesAdditional Help Verpackungsinhalt Allgemeine AnwenderhinweiseMerkmale der MCI Familie Systemvoraussetzungen Installation der TastaturKabelinstallation USB Magnetkartenleser MSR ModuleSmartcard Lese- Schreibgerät SCR Schlüsselschalter KLMicrojoystick ZeigergeräteZusätzliche Hilfe Contenu du colis Caractéristiques de la gamme MCISystèmes requis Installation du clavierRaccordement USB Raccordement PS/2 sans souris tactile ni MicrojoystickRaccordement PS/2 avec Souris tactile et ou Microjoystick Lecteur de carte magnétique MSRLogement et sortie de câble Contrôle de fonctionnementLecteur de carte à puce lecture/écriture SCR Commutateur à clé KLSouris tactile Dispositifs de pointageAide Electronics / Elektronik / Electronique Technical data / Technische Daten / Données techniquesAppendix / Anhang / Annexe Air pressure Relative humidityClimatic test category Mechanical system / Mechanik / MécaniqueTrademarks FCC Warning StatementCopyright