Standard Features | English |
|
Forced Convection Cooling
All Xtant “X” Series amplifiers employ forced convection cooling for thermal management* An on+board thermal sensing circuit regulates fan speed to maintain optimum operating temperature*
Fully Regulated PWM Power Supply
All Xtant “X” Series amplifiers feature a Fully Regulated, Pulse Width Modulated power supply* This supply technology provides high efficiency and consistent output performance even when battery voltage is less than optimum*
Crossover
A $!/!"dB filter network with selectable Bypass (Full Range), High Pass, Low Pass or Bandpass modes of operation* Frequency selection is via a $! pin Frequency SIP* The amplifier is shipped with a &( Hz SIP installed, $' other frequencies are available from your Xtant Dealer*
Noise Gate
Provides deep muting when no musical signal is present* Features include adjustable threshold and bypass switch*
Balanced/Floating Input
When enabled, this circuitry helps to eliminate “system noise” associated with “ground loops”* When combined with the input sensitivity adjustment, it allows the X%(' to accept up to $#V of input signal* Balanced must be used for BTL inputs using the HLA*
Modular Expansion Port
All X series amplifiers are supplied with a modular port(s) used for docking any of Xtant’s signal processing modules*
Protection Circuitry
Both Thermal, Overcurrent and Low Voltage protection are incorporated into the X%('* In the event of a problem, the amplifier will reduce its power to maintain operation* In the case of Low Voltage, the amplifier will shut off when the battery voltage falls to $$ Volts or less*
Passive Output
The RM- Resistor Module is designed to activate the “passive speaker terminals*” It provides
Service Jumper
Removing the jumper will turn+off amplifier when remote turn+on, ground, and
.$! volt cables are connected to amp* Use to service the amplifier or to make any adjustments*
Status LEDs
Four LEDs, visible through the cover, indicate operational status of all Xtant amplifiers* The red LED illuminates when the amplifier is “ON”, the yellow LED indicates that overcurrent protection is engaged, the orange LED indicates that the thermal protection circuit is engaged, and the green LED indicates when the noise gate is engaged and operational*
6
English | Xtant X603 Specifications | ||
| |||
Frequency Response |
| !( Hz to !( KHz ./– $ dB | |
Number of Channels |
| ' | |
Watts per Channel @ "Ω |
| ! x #) . $ x $)( | |
Watts per Channel @ !Ω |
| ! x $)( . $ x '(( | |
Bridged Mono @ "Ω (Stereo Channels) | $ x '(( | ||
Recommended Load (Stereo Channels) | 1!Ω Stereo/1"Ω Bridged | ||
Recommended Load (Mono Channel) | 1!Ω | ||
Distortion (THD) |
|
| 2 *!3 |
Measured at !(Hz to !(kHz at rated power, all channels driven "Ω | |||
Signal to Noise Ratio |
| 1 $(( dB | |
Measured A+weighted in !(kHz noise bandwidth @ $ volt sensitivity | |||
Damping Factor |
| 1 !(( @ $(( Hz with "Ω Load | |
Input Sensitivity |
| $(( mV to | |
|
| $(( mV to $# V RMS Balanced | |
Input to Line Output Gain | ( dB ./– !( dB, Selectable in $( dB Steps | ||
On+Board Crossover | $!/!"dB per Octave Selectable (!) | ||
Line Outputs: |
| Yes, High Pass, Low Pass or Bypass Mode | |
Module Port(s) |
|
| " – Accessory |
Power Supply |
| Fully Regulated, Pulse Width Modulated | |
Operational Voltage |
| $$ to $) Volts | |
Fusing |
|
| Requires $(( amp |
Size (L xW x H): |
|
| !( !$/'!” x - #/- x ! #/'!” |
|
|
| )!)mm x !!)*"mm x ))mm |
Warranty |
| Limited " Year Parts and Labor | |
7