Netopia Network Adapater manual Basic Configurations

Page 23

User Guide

Chapter 6 - Basic Configurations

6.1 WAN Configuration

This page let you configure the WAN settings.

Figure 6-1 WAN Configuration

Static IP Settings:

IP Address:

Range for IP Address is x.x.x.y, where 0 ≤ x≤ 255 and 1 ≤ y≤ 254, default is 192.168.241.101.

Subnet Mask:

Range for Subnet Mask is x.x.x.x, where 0 ≤ x≤ 255, default is 255.255.255.0

Gateway:

Range for Gateway is x.x.x.y, where 0 ≤ x≤ 255 and 1 ≤ y≤ 254, default is 0.0.0.0.

DHCP Clients:

DHCP Client:

This is to enable or disable the VOIP ATA WAN as a DHCP client. DHCP Client is generally used in the following encapsulations: 1483 Bridged IP LLC, 1483 Routed IP LLC, 1483 Bridged IP VC-MUX, 1483 Routed IP VC-Mux, and Classical IP over ATM. This option is for non-static (dynamic) IP addresses.

Host Name:

The Host Name can be up to 19 characters.

User Guide

6-23

Image 23

Contents Netopia Voip ATA User’sGuide Revision Status Tables Of Content Appendix a Glossary User Guide Introduction Audio Codec Feature Main features Call Out & CallCall features Setup & Configuration12V DC Your Voip ATA at a glancePorts and buttons ETH LED descriptionTypical Voip ATA Connection Installing Your Voip ATAAdsl Connection Diagram 2below shows a Cable Modem+Router connection diagram Cable Connection DiagramConnection via Company Network For Company Network ConnectionAccessing GUI Using Static IP Setting Up Your Voip ATA functionality viaAccess to Voip ATA’s GUI User Guide Accessing GUI Using Hub/Switch Accessing GUI Using Hub/SwitchUser Guide Overall Status Setup ModeNetwork Selection Registration Status Basic ModeOverall Status Firmware VersionWAN Statistic Current Voice Call StatusVoice Call Status Descriptions WAN Connection TypeDiscarded Packets Reset CountersTCP Status GeneralSave Log System LogClear Log Basic Configurations Auto Discovered DNS ConfigurationUser Configured DNS ProxyHost IP DNS Proxy SettingDNS Server Setting Save ConfigurationReboot Only Save Settings / RebootSave & Reboot Rebooting Modem Advanced Mode User Guide Registration Interval SIP Service ProviderService Provider List New Service ProviderUser Guide Proxy Port Authentication MethodService Provider Action Registrar PortNew User Profile Voip ATA Login Account ConfigurationPassword User Profile ListSubmit Changes Login ActionDisconnect Timeout Voip ATA Timer ConfigurationPredial Timeout Alert TimeoutUser Guide Call Fwd No Ans Timeout Ring Parameters Ringtone ConfigurationWorking Country New CountryUser Guide Recall Tone Normal Dial ToneRingBack tone Alerting ToneSubmit Changes Stun Parameters Misc ConfigurationSIP Device User Guide Keep Alive Period Stun ServerStun Port Force Keep AliveAddress Book Address Book ConfigurationUser Guide User Guide Http Server Admin PrivilegeMiscellaneous Configuration Sntp Client Admin / Username Password ConfigurationFTP Server Tftp ServerUser Guide Restore Settings Reset to DefaultHow to Firmware Update Firmware UpdateUploading .DLF file 13 Save / Reboot Save / Reboot15 Rebooting Modem Pstn Calls VoIP Advanced Call Features Consultation HoldMaking Phone Calls Internet CallsCall Waiting Attended Transfer4 3-Way Conferencing How To Call Forwarding Forward On No Answer Forward When BusyForward Unconditional Through Server Canceling Call ForwardingCall Return IP Dialing IP AddressProblem Corrective Action TroubleshootingAppendix a Glossary User Guide 10-63 User Guide 10-64 User Guide 10-65 B1.2 Explanation of the Rules Descriptions Appendix B Dial Plan for PulverB1 Basic Dial Plan B1.1 Pulver USA Dial Plan User Guide 10-67 Service Provider Partner Recommended Dial Plan Rule B2 Calling Other Service Provider Numbers through PulverUser Guide 10-69