Microstar G41M manual Load Fail-Safe/ Optimized Defaults, Bios Setup

Page 59

BIOS Setup

Load Fail-Safe/ Optimized Defaults

The two options on the main menu allow users to restore all of the BIOS settings to the default Fail-Safe or Optimized values. The Optimized Defaults are the default values set by the mainboard manufacturer specifically for optimal performance of the mainboard. The Fail-Safe Defaults are the default values set by the BIOS vendor for stable system performance.

When you select Load Fail-Safe Defaults, a message as below appears:

Pressing Y loads the BIOS default values for the most stable, minimal system performance.

When you select Load Optimized Defaults, a message as below appears:

Pressing Y loads the default factory settings for optimal system performance.

3-23

Image 59
Contents MS-7563 v1.X Mainboard G41M seriesTechnical Support Copyright NoticeTrademarks Revision HistorySafety Instructions FCC-B Radio Frequency Interference Statement Micro-Star International MS-7563Weee Waste Electrical and Electronic Equipment Statement Page Vii Contents DOT Dynamic OverClocking Getting Started Getting StartedSata Mainboard SpecificationsLAN IDEMounting SlotsForm Factor G41M Series MS-7563 v1.X Micro-ATX Mainboard Mainboard LayoutPacking Checklist Hardware Setup Hardware SetupQuick Components Guide Introduction to LGA 775 CPU CPU Central Processing UnitCPU & Cooler Installation Lift the load lever up and open the load plate Locking switch DDR2 MemoryDual-Channel Memory Population Rules Volt Notch Installing Memory ModulesJPW1 Power SupplyATX 24-Pin Power Connector ATX1 ATX 12V Power Connector JPW1Back Panel LED Audio PortsFDD1 ConnectorsFloppy Disk Drive Connector FDD1 IDE Connector IDE1SATA2 SATA4 SATA1 SATA3 Serial ATA Connector SATA1 ~ SATA4JCI1 Fan Power Connectors CPUFAN1, SYSFAN1/2Chassis Intrusion Connector JCI1 CPUFAN1SYSFAN1/2JSPD1 IEEE1394 Connector J13941 optionalPDIF-Out Connector JSPD1 CDIN1 Front Panel Connectors JFP1, JFP2CD-In Connector CDIN1 JFP2 JFP1JTPM1 Front Panel Audio Connector JAUD1TPM Module connector JTPM1optional JAUD1USB 2.0 Bracket Front USB Connector JUSB1 ~Serial Port Connector Jcom JUSB1~2JLPT1 Parallel Port Header JLPT1JBAT1 JumperClear Cmos Jumper JBAT1 PCI Peripheral Component Interconnect Slots SlotsPCI Peripheral Component Interconnect Express Slots PCI Interrupt Request Routing Bios Setup Bios SetupPress DEL to enter Setup Entering SetupMain Menu Control KeysGetting Help General Help F1Main Menu Exit Without Saving Bios Setup Load Optimized DefaultsSave & Exit Setup Standard Cmos Features Hard Disk S.M.A.R.T Bios Setup Device / Vender / SizeLBA/Large Mode DMA ModeMS-7563 Mainboard System Information Advanced Bios Features Hpet TCG/TPM Support Integrated Peripherals Parallel Port Mode Bios Setup On-Chip IDE ControllerRAID Mode Device ConfigurationAcpi Standby State Power Management SetupAcpi Function Wake Up Event By Bios Setup Power Button FunctionRestore On AC Power Loss Wakeup Event SetupMS-7563 Mainboard Resume by PCI-E Device Resume by RTC AlarmSYS FAN 1 Control MonitorChassis Intrusion CPU Smart FAN TargetBios Setting Password Cell Menu TRP MS-7563 Mainboard Configure Dram Timing by SPDCAS LatencyCL TRCDAuto Disable DIMM/PCI Frequency Bios Setup TWRAdjusted Dram Frequency MHz Adjust PCI-E Frequency MHzMS-7563 Mainboard Load Fail-Safe/ Optimized Defaults Realtek Audio Click Realtek HD Audio Driver Installing the Realtek HD Audio DriverInstallation for Windows XP/Vista Realtek Audio Software Configuration Environment Simulation Sound EffectLoad MS-7563 Mainboard Equalizer SelectionRaise the key Remove the human voice Lower the key Realtek Audio Frequently Used Equalizer SettingKaraoke Mode Multi-Stream Function Adjust VolumePlayback multi-streaming and click OK to save the setup MixerRealtek Audio Tool MS-7563 Mainboard Playback controlUte Ute Realtek Audio Recording controlAudio I/O Speaker ConfigurationDisable front panel jack detection option Realtek Audio Connector SettingsOutput Source PdifOutput Sampling Rate Realtek Audio Test Speakers Microphone 3D Audio Demo Information Channel Mode for Stereo-Speaker Output Hardware SetupConnecting the Speakers Line Out Rear channels Line Out Rear channels Line Out Center and Subwoofer channel Line Out Front channels Dual Core Center Activating Dual Core Center Dual Core Center MainIntroduction Sharp mode Smooth mode Clock DOT Dynamic OverClocking Clock Voltage FAN Speed Temperature User Profile Dual Core Center