Turbosound TA-880 user manual Voltage Settings, Safety Earthing, AC Power Fusing, Powering Up

Page 47

user manual

TA-880

Voltage Settings

The LMS-D6 is provided with an auto-seeking power supply, and therefore requires no external adjustment for correct operation with international AC line voltages ranging from 60 to 250 volts.

Safety Earthing

The green/yellow wire of mains cord must always be connected to the electrical installation's Safety Earth or Ground. It is essential for personal safety, as well as proper operation of the unit.

The green/yellow wire is internally connected to all exposed metal surfaces. Any rack framework which this unit might be mounted into is assumed to be connected to the same grounding circuit. The LMS-D6 has balanced audio connections and does not require disconnection of this or any other safety earth for the avoidance of hum loops. If any problems are experienced with hums or buzzes, careful attention to the signal cable grounding will effect a cure.

AC Power Fusing

The incoming mains power fuseholder is mounted on the rear panel. If the fuse needs to be replaced it must be properly rated as follows: 20mm 1A 250 V type T. It is important for continued safety that this specification is adhered to. It is very unlikely that this fuse will fail during normal use, and such a situation must be treated with some caution as to the cause.

Powering Up

When the LMS-D6 is switched on by operating the power on-off switch located on the rear panel, the internal circuitry carries out a series of routine diagnostic tests.

After the switch-on cycle, the screen will revert to displaying the delay program name that was in use when the unit was last powered down.

The internal memory automatically saves all settings when the unit is switched off, so there is no need to re-load delay and temperature information every time the system is powered- up. The memory contents are retained indefinitely without the need for an internal backup battery.

TA-880 user manual

Page 47

Image 47
Contents Aspect TA-880 System TA-880 TA-880 Amplifier Rack Signal Wiring Output Connections TA-880 EC Declaration of Conformity Turbosound Aspect System Concepts IntroductionAspect Polyhorn Concept Aspect TA-880 Turnkey System Concept Amplifier Racks Loudspeaker Management System LMS ConceptLMS-D26/D6 Loudspeaker Management Systems Aspect Loudspeaker Components Power AmplifiersDigital Controllers TA-880H Mid/High Enclosure TA-880L Low Frequency EnclosureTSW-218 Subwoofer TA-880LM Low-Mid Enclosure TA-880HM High-Mid EnclosureTransportation Aspect trapezoidal Flying System Overview Flying and StackingRunning Turbosound GigMate / Ease Focus for the first time Gigmate Acoustic SimulationRigging System SetupMapping Properties Audience AreaDesigning a system TA-880 TA-880 TA-880 Safety Notes on Rigging Sample Certificate of Load Test Horizontal Coverage Flying HardwareVertical Coverage Wide and Narrow Flybar settingsTwo-wide trapezoidal flybar FB-880/2W Bottom ViewThree-wide trapezoidal flybar FB-880/3W Flying Chains Short Chain AssemblyFlying Swords Tilting Strap 59mTA-880 TA-880 Flying a vertical column of TA-880 trapezoidal cabinets TA-880 Sword hole position Inter-cabinet angle Single horizontal row Flying a cluster of TA-880 trapezoidal cabinetsWide x 2 deep TA-880H array Wide x 3 deep TA-880H array Tight-packed Flying Assemblies TA-880 Aiming directivity of the stack Bass Enclosure arrayingGround stacking Unpacking Mechanical InstallationLMS Series Loudspeaker Management Systems IntroductionLMS-D6 Loudspeaker Management System LMS-D6 Rear Panel Functions Mains PowerPowering Up Voltage SettingsSafety Earthing AC Power FusingAudio Connections Input and Output Connector WiringTime correction for loudspeaker driver placement LMS-D24 and D26 Loudspeaker Management Systems FeaturesFront Panel Functions TA-880 Rear Panel Functions Creating a Crossover Selecting a Factory PresetOperating the LMS-D24 and D26 Starting up Navigation and Viewing Parameters A Freq Width Gain EQ1 100Hz 1.4Q 0.0dBNavigation Out1 Freq Width Gain EQ1 100Hz 1.4Q 0.0dBPreset Recall PresetsPreset Store Preset Name Store My SystemStereo / Mono Formats DSP Processing Layout Input DSP block diagramOutput DSP block diagram DSP processing Input Channels A Delay 1.50msA Freq Shape HPF 20.0Hz LR24 Parametric filters Parametric EqualisationHigh and Low shelving filters Output Channels Gain and Polarity DelayHigh and Low Pass Filters Out1 Freq Shape LPF 2.50k LR24Out1 Freq Slope Gain EQ- 100Hz 12dB 0.0dB Routing LimitersUtilities Utility functions Serial Comms Port Audio Output Connectors Racking, Cables and Connections AMP-890 Aspect System Amplification RackInput Connections OptionsOutput Connections Amplifier Rack Signal WiringMid-High Outputs Break-out Cables NL4 bass Extension Cables Break-out cables NL8 mid-highMains Connections General Features & Facilities T-45 High Efficiency Audio Power AmplifiersFront Panel Functions T-25 Front Panel Functions T-45 Mechanical Installation Audio Connections & Controls Voltage SettingVoltage Range Input Impedance Gain and Sensitivity SettingsPolarity Damping Factor Attenuation & Gain SettingCooling System Long Speaker LinesTA-880H TA-880HM TA-880LM Appendix a Technical SpecificationsTA-880L TSW-218 Appendix B Warranty TA-880

TA-880 specifications

The Turbosound TA-880 is a high-performance audio solution designed for professional live sound applications. This arrayable large-format loudspeaker system offers remarkable acoustic power, clarity, and reliability, making it a popular choice among sound engineers and event organizers.

One of the standout features of the TA-880 is its advanced driver technology. The loudspeaker is equipped with dual 18-inch neodymium low-frequency transducers that provide deep, punchy bass and impressive output levels. The high-frequency section is supported by a 3-inch titanium compression driver, delivering crystal-clear highs that ensure speech intelligibility and musical detail, even in large venues.

The TA-880 system employs Turbosound's proprietary Waveguide technology, which enables exceptional dispersion control. This means that the sound reaches the audience evenly, minimizing dead spots and providing a consistent listening experience. The speaker's broad horizontal dispersion pattern allows for wider coverage, making it ideal for various settings, from concert halls to outdoor festivals.

Additionally, the TA-880 features a robust, durable construction that can withstand the rigors of touring and extensive use. Its weather-resistant design makes it suitable for both indoor and outdoor applications, ensuring reliability in diverse conditions. The system is also lightweight, facilitating easy transport and setup, allowing sound professionals to focus on delivering exceptional sound rather than wrestling with heavy equipment.

Integration is made seamless with the TA-880 through its compatibility with Turbosound's proprietary digital signal processing (DSP) technology. This innovative feature enables users to fine-tune the system according to specific venue requirements and performance criteria, further elevating sound quality. It also allows for network control, enabling real-time monitoring and adjustments from a single interface.

The TA-880 system is versatile, suitable for a range of applications including concerts, corporate events, and festivals. It can be used as standalone units or as part of a larger array configured for larger venues. Its combination of high output capability, intelligent design, and industry-leading technology makes the Turbosound TA-880 a preferred choice for those who demand excellence in audio performance.

In summary, the Turbosound TA-880 combines advanced driver technology, innovative dispersion solutions, and robust construction, making it an indispensable tool for sound professionals aiming to deliver an unforgettable auditory experience.