POSIFLEX Business Machines LS-1000 instruction

LS-1000 Series

Laser Barcode Scanner

User’s Manual

Rev. A0

FCC Notes: This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions manual, may cause interference to radio communications. It has been tested and found to comply with limits for a Class A digital device pursuant to EN55022 and 47 CFR, Part 2 and subpart J of Part 15 of FCC Rules, which are designed to provide reasonable protection against interference when operated in a commercial environment. Operation of this equipment in a residential area is likely to cause interference in which case the user at his own expense will be required to take whatever measures to correct the interference.

For CE-countries:This scanner is in conformity with CE standards. Please note that an approved, CE-marked power supply unit should be used in order to maintain CE conformance.

Laser Safety: The laser scanner complies with safety standard IEC 60825 –1 for a Class I laser produce. It also complies with CDRH as applicable to a Class IIa laser product. Avoid long term staring into direct laser light.

Radiant Energy: The laser scanner uses one low-power visible laser diodes operating at 650nm in an opto-mechanical scanner resulting in less than 3.9μW radiated power as observed through a 7mm aperture and averaged over 10 seconds.

Do not attempt to remove the protective housing of the scanner, as unscanned laser light with a peak output up to 0.8mW would be accessible inside.

Laser Light Viewing: The scan window is the only aperture through which laser light may be observed from this product. A failure of the scanner motor, while the laser diode continues to emit a laser beam, may cause emission levels to exceed those for safe operation. The scanner has safeguards to prevent this occurrence. If, however, a stationary laser beam is emitted, the failing scanner should be disconnected from its power source immediately.

Adjustments: Do not attempt any adjustments or alteration of this product. Do not remove the protective housing of the scanner. There are no user- serviceable parts inside.

Caution: Use of controls or adjustments or performance of procedures other than those specified herein may result in hazardous laser light exposure.

Optical: The use of optical instruments with this product will increase the eye hazard. Optical instruments include binoculars, magnifying glasses, and microscopes but do not include normal eye glasses worn by the user.

Warranty Limits: Warranty terminates automatically when any person other than the authorized technicians opens the machine. The user should consult his/her dealer for the problem happened. Warranty voids if the user does not follow the instructions in application of this merchandise. The manufacturer is by no means responsible for any damage or hazard caused by improper application.

No part of this document may be reproduced, transmitted, stored in a retrieval system, transcribed, or translated into any language or computer language in any form or by any means electronic, mechanical, magnetic, optical, chemical, manual or otherwise, without express written consent and authorization.

We reserve the right to make changes in product design without reservation and without notification. The material in this guide is for information only and is subject to change without notice.

All trademarks mentioned herein, registered or otherwise, are the properties of their various respective owners.

About This Manual:

Posiflex Technologies, Inc. has made every effort for the accuracy of the content in this manual. However, Posiflex Technologies, Inc. will assume no liability for any technical inaccuracies or editorial or other errors or omissions contained herein, nor for direct, indirect, incidental, consequential or otherwise damages, including without limitation loss of data or profits, resulting from furnishing, performance, or use of this material.

This information is provided “as is” and Posiflex Technologies, Inc. expressly disclaims any warranties, expressed, implied or statutory, including without limitation implied warranties of merchantability or fitness for particular purpose, good title and against infringement.

The information in this manual contains only essential hardware concerns for general user and is subject to change without notice. Posiflex Technologies, Inc. reserves the right to alter product designs, layouts or drivers without notification. The system integrator shall provide applicative notices and arrangement for special options utilizing this product. The user may find the most up to date information of the hardware from: http://www.posiflex.com or http://www.posiflex.com.tw or http://www.posiflexusa.com

All data should be backed-up prior to the installation of any drive unit or storage peripheral. Posiflex Technologies, Inc. will not be responsible for any loss of data resulting from the use, disuse or misuse of this or any other Posiflex product.

All rights are strictly reserved. No part of this documentation may be reproduced, stored in a retrieval system, or transmitted in any form or by any means, electronic, mechanical, photocopying, or otherwise, without prior express written consent from Posiflex Technologies, Inc. the publisher of this documentation.

All brand and product names and trademarks are the property of their respective holders.

Page 1

P/N: 18050900030

LS-1000 specifications

The POSIFLEX Business Machines LS-1000 is a robust point of sale terminal designed for a variety of business environments, including retail and hospitality. Renowned for its reliability and user-friendly interface, the LS-1000 stands out as a key player in modern transaction solutions.

One of the key features of the LS-1000 is its powerful processing capability. It is equipped with an efficient processor that enables swift transaction handling, ensuring that customer wait times are minimized. This efficiency is vital for businesses that face high volumes of customer interactions, allowing staff to focus more on customer service rather than slow technology.

The LS-1000 incorporates a high-resolution touchscreen display that is responsive and easy to navigate. This feature enhances the user experience, allowing employees to interact with the system quickly and effectively. The touchscreen interface is designed with intuitive software that can be customized to meet specific operational needs, making it versatile for different business types.

Durability is another important characteristic of the LS-1000. Built to withstand the rigors of daily use in bustling environments, the terminal features a robust casing that can endure accidental spills, drops, and other common hazards present in commercial settings. This reliability ensures longevity, reducing the need for frequent replacements.

In terms of connectivity, the LS-1000 supports various communication protocols, enabling it to integrate with existing business systems seamlessly. Whether it's linking to inventory management software or connecting with payment processors, this terminal provides the flexibility businesses require to maintain efficiency and connectivity.

Additionally, the LS-1000 supports a range of peripheral devices, including barcode scanners, receipt printers, and cash drawers. This compatibility allows businesses to create a comprehensive point of sale ecosystem tailored to their unique operational demands.

Security features are paramount in the LS-1000 design. It employs advanced encryption and security protocols to protect sensitive customer and business data, thus fostering trust and reliability in transactions.

The energy-efficient design of the LS-1000 is also noteworthy. It consumes minimal power while delivering high performance, which not only lowers operational costs but is also beneficial for environmentally conscious businesses.

In summary, the POSIFLEX Business Machines LS-1000 is a top-choice POS terminal that offers a blend of speed, durability, and adaptability. With its impressive array of features, modern technology, and robust performance, it is well-suited for various retail and hospitality applications, ensuring that businesses can operate smoothly and efficiently.