Lanner electronic 19" 1U Intel Pentium 4 Socket T Rackmount Network Security Platform, FW-7870

Page 33

controller and you have a USB keyboard.

Onboard LAN Control : This setting controls the onboard LAN Controller.

Enabled

Enable Onboard H/W LAN function.

Disabled Disable Onboard H/W LAN function.

LPT/LCM Control : Use this option to enable and configure or disable the LPT/LCM port present on the evaluation board.

Configuration options: LPT / LCM

Signal Dual Status LED : This setting is to set the status when the system is powered on.

Configuration options: Green / RED

Status LED : This setting is to set the status when the system is powered.

Configuration options: Always Blight / DARK / 0.1 sec BLINK / 0.5 sec BLINK

Onboard FDC Controller : Select Enabled if your system has a floppy disk controller (FD0) installed on the system board and you wish to use it. If you install add-on IDC or the system has no floppy drive, select Disabled in the field.

Configuration options: Enabled / Disabled

Onboard Serial Port 1/2 :

Auto

BIOS will automatically setup the port address.

3F8/IRQ4

Enable onboard Serial port

and address is 3F8.

2F8/IRQ3

Enable onboard Serial port

and address is 2F8.

3E8/IRQ4

Enable onboard Serial port

and address is 3E8.

2E8/IRQ3

Enable onboard Serial port

and address is 2E8.

Disabled

Disable onboard Serial port .

UART Mode Select : The serial port on your system may offer a variety of infrared port modes.

Click here for a description of various modes.

UR2 Duplex Mode (Half) : This field is available when UART 2 Mode is set to either ASKIR or

IrDA. This item enables you to determine the infrared function of the onboard infrared chip. The

options are Full and Half (default).

Full-duplex means that you can transmit and send information simultaneously. Half-duplex is the

transmission of data in both directions, but only one direc-tion at a time.

Onboard Parallel Port : This item allows you to determine onboard parallel port controller I/O

address setting. The settings are “378H/IRQ7”, “278H/IRQ5”, “3BC/IRQ7”, “Disabled”.

Parallel Port Mode : Select an operating mode for the onboard parallel (printer) port. Select

“Normal”, “Compatible”, or “SPP” unless you are certain your hardware and software both

support one of the other available modes.

ECP Mode Use DMA : Select a DMA channel for the parallel port for use during ECP mode.

The settings are “3” and “1”.

Page 32 Page 34
Image 33
Page 32 Page 34
Contents User’s Manual FW-7870 SeriesRadio Frequency Emissions Notice Copyright and DisclaimersTrademark Acknowledgments Safety Instructions About this Manual Getting Technical AssistanceTable of Contents Terms and Conditions Warranty Policy RMA Service Features Getting StartedIntroduction Technical Specifications Packing Contents Board Layout MB-X76 System BoardConnector Pin Assignments Jumper Settings and I/O ConnectorPSC124 Pin ATX Power Connector USBF1：USB Port #1 & #2 Connector 2x5 Pin 2.54mm Face Panel FW-7880 19 1U Rackmount Firewall MechanismsFace Panel LED Status and Behavior OrangePage FW-7870 Rear View Rear ViewRemoving the Top Cover FW-7870 Hardware Installation GuideCPU Installation Page System Memory Put the Hard disk on the bracket, and screwing 4 screws Installing Hard Disk DriveInstalling the Mini-PCI Card Installing Compact Flash CardBios Setup Award Bios SetupStarting Setup Using SetupGetting Help Navigating through the menu barMain Menu „ Advanced Chipset FeaturesOptions Description Date Standard Cmos FeaturesIDE Adapters Advanced Bios Features Page Dram Timing Control Advanced Chipset FeaturesPage Integrated Peripherals Onboard Serial Port 1/2 Auto Page Page Video Off Method Power Management SetupSuspend Mode Reset Configuration Data PnP/PCI ConfigurationPC Health Status Load Optimized Defaults Supervisor/User Password SettingLoad Optimized Defaults Y/N ? N Enter Password Save and Exit SetupSave to Cmos and Exit Y/N? Y Quit without saving Y/N? Y Exit Without SavingPower Supply Specification AC Input Spec Power SupplyOutput Specifications FeatureDetail Register Descriptions Watchdog TimerCRF6 Default Console Redirection P e n d i x CLCM & KeyPad Function Library description LCD Module and Key Pad For FW-7870Page Terms and Conditions Warranty PolicyWithout this form your RMA will be Rejected RMA Service Request FormPEXNSD01-040709 Version 1.0 Printed and published in Taiwan
Top Page Image Contents