SOYO SY-7IWA-F user manual Chapter, Preparations

Page 21

Hardware Installation	SY-7IWA-F
Chapter 2
HARDWARE INSTALLATION

Congratulations on your purchase of SY-7IWA-FMotherboard. You are about to install and connect your new Motherboard.

Note: Do not unpack the Motherboard from its protective anti- static packaging until you have made the following preparations.

2-1 PREPARATIONS

Gather and prepare all the following hardware equipment to complete the installation successfully:

1.Slot 1 processor with built-in CPU cooling fan (boxed type).

Note: This Motherboard supports non-boxed type CPUs. The heavier CPU cooling fan requires the installation of a CPU support stand.

2.DIMM memory module

3.Computer case and chassis with adequate power supply unit

4.Monitor

5.PS/2 Keyboard

6.Pointing Device (PS/2 mouse)

7.Speaker(s) (optional)

8.Disk Drives: HDD, CD-ROM, Floppy drive …

9.External Peripherals: Printer, Plotter, and Modem (optional)

10.Internal Peripherals: Modem and LAN cards (optional)

17

Image 21

Contents SY-7IWA-F Edition August SY-7IWA-FVersion 7IWA-F SerialTable of Contents SY-7IWA-F Introduction KEY FeaturesSY-7IWA-F Handling the Motherboard Electrostatic Discharge PrecautionsIntel SY-7IWA-F Motherboard LayoutSY-7IWA-F Motherboard Components SY-7IWA-F New design with big benefits ChipsetSY-7IWA-F Product Highlights Features BenefitsAccelerated Graphics Port A.G.P Product Package¿Note Universal Serial Bus USBIDE Support I/O Interface Controller Real-Time Clock, Cmos SRAM, and BatterySerial Ports Parallel Port4 PS/2 Keyboard and Mouse Interface Diskette Drive ControllerCD Line in Connector Audio ConnectorAudio Subsystem Hardware MonitorWake on LAN Technology Preparations ChapterUnpacking the Motherboard Installation Guide Begin the InstallationTo install the CPU, follow the steps below CPU InstallationSY-7IWA-F Sdram Memory Module Installation Hardware Installation Number MemoryModules Double-sided Single-sided Single-sided² RAM Type IDE Motherboard Connector IDE Device Installation HDD, CD-ROMFDC Floppy Drive InstallationFront Panel Connections Power LED & KeyLockReset SpeakerAcpi LED IDE LED ATX Power On/Off SwitchBack Panel Connections PS/2 Mouse Parallel Port PRTVGA monitor connector Flat Panel ConnectorUniversal Serial Bus USB1/USB2 Onboard Joystick port/audioSerial Port COM 1 and COM2 Other ConnectionsWake-On-LAN WOL Wake-On-LAN JP44 Pin AssignmentCD Line-in J10,J11 Infrared IR1CPU Cooling Fan Cpufan Pin Assignment Cooling Fan Installation CPU Cooling FanChassis Cooling Fan Power Cooling FanAGP VGA Card ATX Power SupplyGND Ø Pay special care to the directionality ATX PowerAMR Audio Modem Riser Connector Auto Mode Jumper Setting Set J6 &JP2 to configure CPU FSB FrequencyManual Mode JP2Enable/Disable Power-On by Keyboard JP1 Set JP9 for FWH Boot Block Write-ProtectKeyboard JP11 Setting Power-On by Win 98 Hot Key USBJP15 Setting JP16 Setting CPU Core Voltage Adjust JP15, JP16Power On JP5 SettingCmos Clearing JP5 Cmos ClearingCmos Setup Utility Copyright C 1984-1999 Award Software Quick Bios SetupSelect Load Optimized Defaults Select Standard Cmos SetupSelect Soyo Combo Feature Select Save & Exit SetupWhat should I do if the Motherboard refuses to start? Troubleshooting at First StartPower Off Modifying selected items Selecting itemsFunction Command Description Exit Without Saving Save and Exit SetupSoyo Combo Setup Soyo Combo SetupBios Setup Utility Quick CPU Frequency Setup2 L2 Cache Memory System Boot Control Settings Setting Description SmaaSystem Boot Control Settings Boot Other Device AC97 Audio/Modem Setting DescriptionKB Power on Setting DescriptionPassword Hot Key PowerStandard Cmos Setup Date Time Display Setting Please NoteDate & Time Floppy Drives Hard Disks Type & ModeHalt On Setting Description VideoAdvanced Bios Features Floppy Driver Settings Setting Description Anti VirusBoot Up Floppy Seek ProtectionSetting Description Gate A20 Setting Description Boot UpNumLock StatusSecurity Option Other Control OptionsDRAM64MB Advanced Chipset Features Latency Time To-CAS Delay System BiosSdram Cycle Time Tras/TrcInitial Display Paging ModeCache CAS# LatencyIntegrated Peripherals Uart Mode SelectIDE Device Controls IDEKeyboard Controls Setting IDE HDD Block Mode FDC Controls Setting Onboard FDCOnboard Serial Setting Description Mode Onboard Serial Setting Description Ports UR2 DuplexOnboard Parallel Ports DMAPWR-Fail Setting Description Pwron AfterGame Port Address Midi Port AddressDpms Power Management SetupIRQ Power Management ControlsUSB KB Reload Global Timer EventsIDE0, IDE1 FDD, COMPNP/PCI Configuration Setup Installed Setting Description Controls PnP OSReset ConfigurationPNP/PCI Configuration Setup PC Health Status Pwrfan Speed Vcore, VTT, 3.3V, +5V, +12V, VBAT, 5VSB CPU Device MonitoringLoad Optimized Defaults Y/N? Y Load Optimized DefaultsLoad Fail Safe Defaults Y/N? Y Load FAIL-SAFE DefaultsSupervisor Password Entering the password User PasswordIDE HDD Auto Detection Soyo CD Start Up Program Menu Insert the Soyo CD into the CD-ROM driveInstall Drivers Read Soyo 7IWA-F ManualManual Selection Menu Intel Whitney .inf utility for Win Intel Whitney VGA Drivers for Win83627hf Winbond Hardware Doctor for Win 95/98 Intel Whitney security utility for Win 9x/NTCrystal Codec driver for Win95 Crystal Wave SynthesizerEnter the Soyo CD Uninstalling/Re-Installing Crystal Audio Drivers Crystal Audio Driver InstallationSpecial Design Considerations Known LimitationsUninstalling or Updating Crystal Audio Drivers Installing Crystal Audio Drivers for Windows NTSY-7IWA-F