Silicon Image SSD-D16G(I)-3600 Set Features EFh, Set Features’ Attributes, Feature Operation

Page 57

ATA COMMAND BLOCK AND SET DESCRIPTION

SSD-DXXX(I)-3600 DATA SHEET

Set Features — EFh

The Set Features command allows the host to configure the feature set of the device according to the attributes listed in Table 48.

Table 47: Set Features — EFh

Register	D7	D6	D5	D4		D3	D2		D1	D0
Feature				Feature

Sector Count				X

Sector Number				X

Cylinder Low				X

Cylinder High				X

Drive Head	X	X	X	Drive				X

Command				EFh

	Table 48: Set Features’ Attributes

Feature	Operation

01h	Enable 8-bit data transfer

66h	Disable reverting to power on defaults

81h	Disable 8-bit data transfer

BBh	4 bytes of data apply on Read/Write Long commands

CCh	Enable revert to power on defaults

On power-up or following a hardware reset, the device is set to the default mode 81h.

SILICONSYSTEMS PROPRIETARY

This document and the information contained within it is confidential and proprietary to SiliconSystems, Inc.

All unauthorized use and/or reproduction is prohibited.

3600D-04DSR

PAGE 48

FEBRUARY 2, 2009

Image 57

Contents Overview FeaturesRevision History UpdatedDocument No Release Date Changes AddedTable of Contents SSD-DXXXI-3600 Data Sheet Related Documentation Sales and Support Part NumberingList of Figures List of Tables Idle Immediate 95h, E1h SSD-DXXXI-3600 Data Sheet Physical Dimensions Physical SpecificationsPin Locations Product Specifications System Power RequirementsSystem Performance SiliconDrive Part# Capacity Service Life GB Written per Day ReliabilityOperational Life Span Product Capacity Specifications Environmental SpecificationsProduct Capacity Number Bytes Sectors Cylinders Heads Track Electrical Specification Pin AssignmentsPin Signal Name Pins Type Description Signal DescriptionsData Inputs/Outputs. This is the 8-bit or Disk Active/Slave Present. This openController by -IORD and -IOWR. This signal DMA Request. This signal is used for DMAGround. The device ground signal Interrupt Request. This signal is an activeSymbol Parameter Minimum Maximum Units Device Power Supply. The device powerSymbol Parameter Maximum Units Absolute Maximum RatingsSymbol Parameter 5V ±10% Units Minimum Maximum DC CharacteristicsO Access Read Timing Access Read TimingO Access Write Timing Access Write TimingTrue IDE Read/Write Access Timing True IDE Read/Write Access TimingTrue IDE Multiword DMA Read/Write Access Timing True IDE Multiword DMA Read/Write Access TimingTask File Register Specification ATA and True IDE Register DecodingCS0# CS1# DA02 DA01 DA00 ATA Registers Error RegisterOperation Feature RegisterRead/Write ByteSector Count Register Read/Write Sector Count Default ValueSector Number Register Read/WriteLogical Block Number bits A07-A00 LBA Addressing Cylinder Low Register LowLogical Block Number bits A15-A08 LBA Addressing Logical Block Number bits A23-A16 LBA Addressing Cylinder High RegisterLBA27 LBA26 LBA25 LBA24 Drive/Head RegisterDrive Write Fault DWF. Always set to Status RegisterCorrected Data CORR. Always set to Operation Read/Write ATA Command Code Command RegisterAlternate Status Register Device Control Register WriteNIEN Device Address Register Read/Write NWTG NHS3 NHS2 NHS1 NHS0 NDS1 NDS0 Default ValueATA Command Block and Set Description ATA Command Block and SET DescriptionATA Command Set Class Command Name Registers Used CodeATA Command Set Check Power Mode 98h, E5h Check Power Mode 98h, E5hRegister Executive Drive Diagnostic 90h Executive Drive Diagnostic 90hDrive Head Number LBA27-24 Command 50h Format Track 50hFormat Track 50h Identify Drive ECh Identify Drive EChIdentify Drive Drive Attribute Data Word Data Default Bytes Data Description AddressIdentify Drive Drive Attribute Data Identify Drive Drive Attribute Data Idle 97h, E3h Idle 97h, E3hIdle Immediate 95h, E1h Idle Immediate 95h, E1hInitialize Drive Parameters 91h Initialize Drive Parameters 91hDrive Command 1Xh Recalibrate 1XhRecalibrate 1Xh Read Buffer E4h Read Buffer E4hDrive Head Number LBA27-24 Command C8h Read DMA C8hRead DMA C8h Drive Head Number LBA27-24 Command C4h Read Multiple C4hRead Multiple C4h Drive Head Number LBA27-24 Command 20h or 21h Read Sector 20h, 21hRead Sector 20h, 21h Drive Head Number LBA27-24 Command 22h or 23h Read Long Sectors 22h, 23hRead Long Sectors 22h, 23h Drive Head Number LBA27-24 Command 40h or 41h Read Verify Sectors 40h, 41hRead Verify Sectors 40h, 41h Drive Head Number LBA27-24 Command 7Xh Seek 7XhSeek 7Xh Set Features EFh Set Features EFhSet Features’ Attributes Feature OperationSet Multiple Mode C6h Set Multiple Mode C6hSet Sleep Mode 99h, E6h Set Sleep Mode 99h, E6hStandby 96h, E2h Standby 96h, E2hStandby Immediate 94h, E0h Standby Immediate 94h, E0hWrite Buffer E8h Write Buffer E8hDrive Head NumberLBA27-24 Command CAh Write DMA CAhWrite DMA CAh Drive Head NumberLBA27-24 Command C5h Write Multiple C5hWrite Multiple C5h Drive Head Number LBA27-24 Command 30h or 31h Write Sectors 30h, 31hWrite Sectors 30h, 31h Drive Head Number LBA27-24 Command 32h or 33h Write Long Sectors 32h, 33hWrite Long Sectors 32h, 33h Drive Head Number LBA27-24 Command C0h Erase Sectors C0hErase Sectors C0h Extended Error Codes Description Extended Error CodesRequest Sense 03h Request Sense 03hDrive Head Number LBA27-24 Command 87h Translate Sector 87hTranslate Sector 87h Wear-Level F5h Wear-Level F5hDrive Head Number LBA27-24 Command CDh Write Multiple w/o Erase CDhWrite Multiple w/o Erase CDh Drive Head Number LBA27-24 Command 38h Write Sectors w/o Erase 38hWrite Sectors w/o Erase 38h Drive Head Number LBA27-24 Command 3Ch Write Verify 3ChWrite Verify 3Ch Part Numbering Sales and SupportPart Numbering Nomenclature Part NumbersFront Label Lot Code Information Standard Back Label withRelated Documentation Related Documentation