Silicon Image SSD-D32G(I)-4300 manual Min Max Min. Max

Page 34

ELECTRICAL SPECIFICATION												SSD-DXXX(I)-4300 DATA SHEET
	Table 13: UDMA Data Burst Timing Requirements (Continued)

	Symbol	Mode 0			Mode 1		Mode 2		Mode 3		Mode 4		Comment (see Notes 1 and	Units
													Comment (see Notes 1 and
		Min.	Max.		Min.	Max.	Min. Max.		Min. Max.		Min. Max.		2)
		Min.	Max.		Min.	Max.	Min. Max.		Min. Max.		Min. Max.		2)

	tDVS	70	-		48	-	30	-	20	-	6	-	Data valid setup time at	ns
													sender (from data valid until
													STROBE edge) (see Note 4).

	tDVH	6	-		6	-	6	-	6	-	6	-	Data valid hold time at sender	ns
													(from STROBE edge until
													data may become invalid)
													(see Note 4).

	tFS	0	230		0	200	0	170	0	130	0	120	First STROBE time (for	ns
													device to first negate
													DSTROBE from STOP during
													a data-in burst).

	tLI	0	150		0	150	0	150	0	100	0	100	Limited interlock time (see	ns
													Note 3).

	tMLI	20	-		20	-	20	-	20	-	20	-	Interlock time with minimum	ns
													(see Note 3).

	tUI	0	-		0	-	0	-	0	-	0	-	Unlimited interlock time (see	ns
													Note 3).

	tAZ	-	10		-	10	-	10	-	10	-	10	Maximum time allowed for	ns
													output drivers to release
													(from asserted or negated).

	tZAH	20	-		20	-	20	-	20	-	20	-	Minimum delay time required	ns
													for output.

	tZAD	0	-		0	-	0	-	0	-	0	-	Drivers to assert or negate	ns
													(from released).

	tENV	20	70		20	70	20	70	20	55	20	55	Envelope time (from DMACK-	ns
													to STOP and HDMARDY-
													during data-in burst initiation,
													and from DMACK to STOP
													during data-out burst
													initiation).

	tSR	-	50		-	30	-	20	-	NA	-	NA	STROBE to DMARDY- time	ns
													(if DMARDY- is negated
													before this long after
													STROBE edge, the recipient
													receives no more than one
													additional data word).

	tRFS	-	75		-	70	-	60	-	60	-	60	Ready-to-final STROBE time	ns
													(no STROBE edges are sent
													this long after negation of
													DMARDY-).

	tRP	160	-		125	-	100	-	100		100	-	Minimum time to assert STOP	ns
													or negate DMARQ.

	tIORDYZ	-	20		-	20	-	20	-	20	-	20	Maximum time before	ns
													releasing IORDY.

	tZIORDY	0	-		0	-	0	-	0	-	0	-	Minimum time before driving	ns
													STROBE (see note 5).

	tACK	20	-		20	-	20	-	20	-	20	-	Setup and hold times for	ns
													DMACK- (before assertion or
													negation).

SILICONSYSTEMS PROPRIETARY

This document and the information contained within it is confidential and proprietary to SiliconSystems, Inc.

All unauthorized use and/or reproduction is prohibited.

4300D-00DSR

PAGE 25

FEBRUARY 27, 2009

Image 34

Contents Overview FeaturesSisecure Document No Release Date Changes Revision History4300D-00DSR February 27 Initial release Table of Contents Task File Register Specification Sales and Support Part Numbering Related DocumentationList of Figures List of Tables Idle Immediate 95h, E1h Part Numbering Nomenclature Physical Specifications Physical DimensionsPin Locations System Power Requirements Product SpecificationsSystem Performance Operational Life Span SiliconDrive Part# Capacity Service Life GB Written per DayReliability Years 402.9GB SSD-D004G-4300Environmental Specifications Product Capacity SpecificationsProduct Capacity Number Bytes Sectors Cylinders Heads Track Pin Electrical SpecificationPin Assignments Ultra DMAData Inputs/Outputs. This is the 8-bit or Signal DescriptionsSignal Name Pins Type Description Disk Active/Slave Present. This openDMA Request. This signal is used for DMA Transfers between the host and deviceInterrupt Request. This signal is an active This signal is a DMA request that is usedGround. The device ground signal For DMA data transfers between the hostWhen Udma mode DMA read is active Channel Ready. The signal is negatedWhen Udma mode DMA write is active Device I/O Read. This is the read strobeSymbol Parameter Minimum Maximum Units Device Power Supply. The device powerAbsolute Maximum Ratings DC Characteristics Symbol Parameter 5V ± 10% Units Minimum MaximumTrue IDE PIO Mode Read/Write Access Timing True IDE PIO Mode Read/Write Access Timing DiagramTrue IDE PIO Mode Read/Write Access Timing True IDE PIO Multiword DMA Read/Write Access Timing True IDE PIO Multiword DMA Read/Write Access Timing Symbol Mode 0 Mode Mode 3 Mode 4 Note UnitsUltra DMA Data Burst Timing Requirements Initiating a Udma Data-In BurstSustained Udma Data-In Burst Device Terminating a Udma Data-In Burst Host Terminating a Udma Data-In Burst Initiating a Udma Data-Out Burst Device Pausing a Udma Data-Out Burst Host Terminating a Udma Data-Out Burst Device Terminating a Udma Data-Out Burst Udma Data Burst Timing RequirementsMin Max Min. Max Time from Strobe edge to ns ATA and True IDE Register Decoding Task File Register SpecificationCS0# CS1# DA02 DA01 DA00 Error Register ATA RegistersRead/Write Feature RegisterOperation ByteRead/Write Sector Count Default Value Sector Count RegisterRead/Write Sector Number RegisterLogical Block Number bits A07-A00 LBA Addressing Low Cylinder Low RegisterLogical Block Number bits A15-A08 LBA Addressing Cylinder High Register Logical Block Number bits A23-A16 LBA AddressingDrive/Head Register LBA27 LBA26 LBA25 LBA24Status Register Drive Write Fault DWF. Always set toCorrected Data CORR. Always set to Command Register Operation Read/Write ATA Command CodeAlternate Status Register Write Device Control RegisterNIEN Read/Write NWTG NHS3 NHS2 NHS1 NHS0 NDS1 NDS0 Default Value Device Address RegisterATA Command Set ATA Command Block and SET DescriptionATA Command Block and Set Description Class Command Name Registers Used CodeATA Command Set Check Power Mode 98h, E5h Check Power Mode 98h, E5hRegister Executive Drive Diagnostic 90h Executive Drive Diagnostic 90hFormat Track 50h Drive Head Number LBA27-24 Command 50hFormat Track 50h Identify Drive ECh Identify Drive EChWord Data Default Bytes Data Description Address Identify Drive Drive Attribute DataIdentify Drive Drive Attribute Data Identify Drive Drive Attribute Data Idle 97h, E3h Idle 97h, E3hIdle Immediate 95h, E1h Idle Immediate 95h, E1hInitialize Drive Parameters 91h Initialize Drive Parameters 91hRecalibrate 1Xh Drive Command 1XhRecalibrate 1Xh Read Buffer E4h Read Buffer E4hRead DMA C8h Drive Head Number LBA27-24 Command C8hRead DMA C8h Read Multiple C4h Drive Head Number LBA27-24 Command C4hRead Multiple C4h Read Sector 20h, 21h Drive Head Number LBA27-24 Command 20h or 21hRead Sector 20h, 21h Read Long Sectors 22h, 23h Drive Head Number LBA27-24 Command 22h or 23hRead Long Sectors 22h, 23h Read Verify Sectors 40h, 41h Drive Head Number LBA27-24 Command 40h or 41hRead Verify Sectors 40h, 41h Seek 7Xh Drive Head Number LBA27-24 Command 7XhSeek 7Xh Set Features’ Attributes Set Features EFhSet Features EFh Feature OperationSet Multiple Mode C6h Set Multiple Mode C6hSet Sleep Mode 99h, E6h Set Sleep Mode 99h, E6hStandby 96h, E2h Standby 96h, E2hStandby Immediate 94h, E0h Standby Immediate 94h, E0hWrite Buffer E8h Write Buffer E8hWrite DMA CAh Drive Head NumberLBA27-24 Command CAhWrite DMA CAh Write Multiple C5h Drive Head NumberLBA27-24 Command C5hWrite Multiple C5h Write Sectors 30h, 31h Drive Head Number LBA27-24 Command 30h or 31hWrite Sectors 30h, 31h Write Long Sectors 32h, 33h Drive Head Number LBA27-24 Command 32h or 33hWrite Long Sectors 32h, 33h Erase Sectors C0h Drive Head Number LBA27-24 Command C0hErase Sectors C0h Request Sense 03h Extended Error CodesExtended Error Codes Description Request Sense 03hTranslate Sector 87h Drive Head Number LBA27-24 Command 87hTranslate Sector 87h Wear-Level F5h Wear-Level F5hWrite Multiple w/o Erase CDh Drive Head Number LBA27-24 Command CDhWrite Multiple w/o Erase CDh Write Sectors w/o Erase 38h Drive Head Number LBA27-24 Command 38hWrite Sectors w/o Erase 38h Write Verify 3Ch Drive Head Number LBA27-24 Command 3ChWrite Verify 3Ch Part Numbering Nomenclature Sales and SupportPart Numbering Part NumbersStandard Back Label with Front Label Lot Code InformationRelated Documentation Related Documentation

SSD-D32G(I)-4300 specifications

The Silicon Image SSD-D32G(I)-4300 is a high-performance solid-state drive designed to meet the needs of both consumer and enterprise users. With a capacity of 32GB, this SSD offers an ideal balance of performance, reliability, and affordability. One of the main features of the SSD-D32G(I)-4300 is its use of advanced NAND flash memory technology, which provides faster data access and improved durability compared to traditional hard disk drives.

This SSD utilizes a SATA III interface, enabling data transfer rates of up to 6 Gbps. This interface ensures that users can experience rapid read and write speeds, making it an excellent choice for tasks requiring quick data retrieval, such as booting operating systems, loading applications, or transferring large files. In real-world usage, users can expect read speeds of up to 520 MB/s and write speeds of roughly 440 MB/s, making it suitable for both everyday computing and more demanding applications.

Another significant characteristic of the SSD-D32G(I)-4300 is its durability and reliability. With no moving parts, this solid-state drive is less susceptible to mechanical failures often associated with traditional HDDs. It features a mean time between failure (MTBF) rating that signifies an impressive lifespan, offering users peace of mind regarding data integrity.

Moreover, the Silicon Image SSD is equipped with various technologies to enhance performance and longevity. Wear leveling ensures even distribution of write and erase cycles across flash memory cells, effectively extending the life of the SSD. Additionally, the drive incorporates error correction code (ECC) technology that detects and corrects data corruption, further safeguarding important information.

The compact form factor of the SSD-D32G(I)-4300 allows for easy integration into various systems, including desktops and laptops. Its energy-efficient design also contributes to improved battery life in portable devices, which is a crucial consideration for on-the-go users.

In summary, the Silicon Image SSD-D32G(I)-4300 is a versatile and reliable solid-state drive that caters to a range of needs. With its fast data transfer speeds, advanced technologies, and durable construction, it represents an excellent choice for users looking to upgrade their storage solution. Whether for enhancing computing efficiency or increasing overall system performance, this SSD is ready to deliver.