Unitech MP300 manual Regulatory Notes and Warranty, Supply Specifications, FCC Part 15 Class B

Page 17

Supply Specifications

Part Number

Description

Supply

Thermal direct receipt paper

 

 

Supply Thickness

2.2 to 3.5 mils (receipt paper)

Supply Width

3.125”

 

 

Supply Length

1 roll of receipt paper is approx. 600” (15,240 mm)

Supply Sensing

Black mark (on face of supply)

Paper Roll Diameter

Outside: 1.375”

Inside: .25”

 

Maximum Print Area

2.85” X 8”

 

Kansaki: P300, P310, P350, P354, P390, P394,

Approved Vendors

P530UV, TO281CA, OP200, TO381N

Jujo: TF-50KS-E2C

 

 

Honshu: FH65BV-3

Copyright 2008 Unitech Electronics Co., Ltd. All rights reserved. Unitech is a registered trademark of Unitech Electronics Co., Ltd.

32

Chapter 8

Regulatory Notes and Warranty

FCC Part 15 Class B

This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

Reorient or relocate the receiving antenna.

Increase the separation between the equipment and the receiver.

Connect the equipment into an outlet on a circuit different from which the receiver is connected.

Consult the dealer or an experienced radio/TV technician for help.

For Bluetooth equipped printers please note:

The printer contains an OEM Serial Port Adapter from connectBlue with FCC ID: PVH070101. This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: “(1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.”

Warranty

This printer is warranted by Unitech to be free of defects in parts and workmanship for a period of one year from date of shipment. This warranty does not apply to defects resulting from action of the user such as misuse, improper wiring, operation outside of specification, improper maintenance or repair or unauthorized modification. Unitech specifically disclaims any implied warranties of merchantability or fitness for a specific purpose and will not be liable for any direct, indirect, special, incidental or consequential damages. Unitech’s total liability is limited to the repair or replacement of the product. The warranty set forth above is inclusive and no other warranty, whether written or oral is expressed or implied.

Copyright 2008 Unitech Electronics Co., Ltd. All rights reserved. Unitech is a registered trademark of Unitech Electronics Co., Ltd.

33

Image 17
Contents MP300 Mobile Printer Support About This ManualTable of Contents What’s in the Box Getting StartedIntroducing the MP300 Communication Options Tour of the MP300Declaration of Conformity Installing the Battery Installing and Charging the BatteryCharging the Battery Battery NoticesAttaching the Belt Clip LED Indicator State StatusReading the LED Status Tearing Paper Loading SuppliesAdding Paper Initial Power Up and Self-Test Using the PrinterConnecting the Printer DIP Switch LocationSetting DIP Switches DIP Switch Functions Serial Communication SpecificationRJ45 Connector Pin # CommunicationMagnetic Stripe Reader Option Infrared Communication Mode IrDABluetooth Communication Option Printer Font Commands Printer Font Commands Courier Character SetProgramming Information Ascii Control CharactersSmart Card Reader Control Commands when SCR is installed Magnetic Stripe Reader Commands When MSR is InstalledGraphic Logo and Bar Code Commands Printer Supervisory and Control CommandsPrint-Head Cleaning Printer MaintenanceCharging the Printer Battery Verifying Battery Charge StateTo Test the DC Power Trouble ShootingTo Test if the Battery is Accepting the Charge Battery and Safety InformationPrinter Specifications SpecificationsPrinter Supplies Part Number DescriptionSupply Specifications Regulatory Notes and WarrantyWarranty FCC Part 15 Class BWarranty and/or Repair Service