Uniden UBC9000XLT manual Care and Mai ntenance

Page 53

Care and Mai ntenance

General Use

Write down the programmed channels/frequencies in case of a memory loss.

Firmly press each scanner key so that you hear the entry tone.

Location

If strong interference or electrical noise is received, move the scanner. Also, a higher antenna ,locationusually results in better reception.

Do not use the scanner in high-moisture environments,such as a kitchen or bathroom.

Avoid placing the scanner in direct sunlight or near heating elements or vents.

Cleaning

Disconnect the AC adaptor while you clean the scanner.

Clean only the outside of the scanner with a mild detergent.

To prevent scratches, do not use abrasive cleaners or solvents to clean the scanner.

Do not rub the display window.

Do not use excessive amounts of water.

Repairs

Do not attempt any repairs. The scanner contains no user-serviceable parts. Contact the Uniden Customer Service Division or take the scanner to a

qualified repair technician.

~--	-----.-----.

Image 53

Contents BC9000XL T 1234 IfEEBefore you use this scanner, please read and observe FollowingTable of Contents Utility Included with the UBC9000XL T RotaryTunerControl Feature HighlightsExternal Speaker Jack-Allow you to connect an external Getting Started Base InstallationSearching What is Scanning?~ ~ 6m ~ Installing the Ctcss BoardLOo Rotary Tuner and Controls Using the Rotary TunerChannel Number Bank Programming Channels@ @ EJEl8Programming By Manual Entry Bank a ch 22 LlO OOO.OOOOMHz Bank a P ch 1 LlO OOO.OOOOMHzBank B ch Bank a P chLlO OOO.OOOOMHz Bank C ch 52 LlO OOO.OOOOMHzBank C Bank C ch 52 123.7750MHzNFM 450.3875MHz 12.5KHz200 450.3875MHz Bank H ch200 OOO.OOOOMHz Enter Bank or ch 450.3875MHz450.3875MHzI Bank H ch200 450.3875MHz 12.5KHz ch- NFM 450.3875MHzNFM 810.0000MHz NFM 856.0000MHz Programming With Auto StoreNFM 456.0000MHz NFM 810.0000MHz 12 K~ Srbef1 NFM 81-oJ,OOOMHZ Store endNumber.Bank D ch 86 854.8625MHz Transferring a Programmed FrequencyPress~ Bank D ch Bank D ch 83 855.9125MHzBank a ch 8 OOO.OOOOMHz 855.9125MHzBank D 855.9125MHz 855.9125MH~Bank RNOPQRSTU ch ~NOPQRSTU chLocal Police Select chan from 1 toFrom 1 to soJI SelectALPHAor Ctcss Select chan ~8t from 1 to 01\Press Scan I, IMANUAL, or Prog Ito exitthe ProgramAlpha Bank a chPress~ to storethe changes Ean~ Abcbefghij Scan ModeBank a ch 8SS.912SMHz~. ~ ~G~,~ I,!KJ. IT Ean~Turning Banks on or OFF ABCeEFGHIJ~c ~!1 == f I, 5 7 Sank. AB€DEFCh105 LlO 853.1125MHzUnlocking a Channel Bank a P ch~Bank a ch Sean-1~Bank a P ch Beginning a Search Search ModeNFM 46.0000MHz NFM 856.0000MHzI NFM 46.0000MHz NFM 48.0000MHz0KHz Search Keys, and Rotary Tuning Controls47.700 ~ ~ Scrolling Frequencies During a Search46.0150MHz Using Turbo SearchUsing Search Delay Locking Out Frequencies Search, Mode, Numeric Keys Rotary Tuning Controls~~~ 46.0550MHzBirdies LID 47.2250MHzStatus, Search, Mode, Numeric and Special Function Keys Additional Scanner FeaturesUsing Data Skip Changing the Frequency Step Press~ To stop SearchRa.~ Setting the Signal ModeStatus, Numeric and Special Function Keys IiSRC-WFM-5.0KHz855.9125MHz Bank DBank C ch Preventing Accidental Programming@ @ Bank a P ch 1 482.7625MHzCount01P ch Displaying Bank MemoryStatus Status, Scan, and Numeric Keys Rotary Tuning ControlsBank E ch 854.9800MHzBank a P ch 1 482.7625MHz Record ch 1 482.7625MHz Using Auto RecordingM ~ lfIJi 482.7625MHz RecordBank C ch 72 854.2875MHz Bank a0KHz ch~O~ Bank C ch 72 CTCSSOFF000.0Bank C ch Iii~lltli Using Hi-CutDisplay Light Status and Special Function Keys~ ~ fim~ Installing the Ctcss Board0000 From Using Ctcss S54.2875MHz Select chan j,1f from 1 to ~O!\From 1 to SIde \.. .2875MHzOHz ch OHz -chCtcss Tone Frequencies Select Chan FromOHz- ch 72 -- / I 854.2875MHz Care and Mai ntenance Troubleshooting Optional Accessories and Replacement Parts Specifications Uniden UBC9000XLT Auto Scanner Australian 1 Year Warranty WarrantyUnl. I!n@