Panasonic Network Adaptor manual Transistor NPN output specifications For Y0 to Y4

FP-e Series

Technical data

■Transistor NPN output specifications (For Y0 to Y4)

Item		Description
Insulation method		Optical coupler
Output type		Open collector
Rated load voltage		5 to 24 V DC
Operating load voltage range		4.75 to 26.4 V DC
Max. load current		0.5 A
Max. surge current		1 A
Output points per common		5 points/common
OFF state leakage current		100 µA or less
ON state voltage drop		1.5 V or less
	OFF to ON	50 µs or less (For Y0 and Y1),
Response		1 ms or less (For Y2,Y3 and Y4)
time	ON to OFF	50 µs or less (For Y0 and Y1),
		1 ms or less (For Y2,Y3 and Y4)
External power	Voltage	21.6 to 26.4 V DC
supply (For driving	Current	6 mA/point (For Y0 and Y1)
internal circuit)		3 mA/point (For Y2, Y3, and Y4)
Surge absorber		Zener diode
Operating indicator		LCD display (I/O monitor mode)

■Relay output specifications (Y5)

Item		Description
Output type		Normally open (1 Form A)
Rated control capacity		2 A 250 V AC, 2 A 30 V DC
Output points per common		1 point/common
Response time	OFF to ON	Approx. 10 ms
	ON to OFF	Approx. 8 ms
Life time	Mechanical	Min. 2 ⋅ 107 operations
	Electrical	Min. 105 operations (resistive load)
Surge absorber		None
Operating indicator		LCD display (I/O monitor mode)

■COM. port communication specifications ∗1)

Item	Description
COM. port type	RS232C ∗2)	RS485
Isolation status with	Non-isolated	Isolated
the internal circuit
Transmission distance	15 m	1200 m
Baud rate ∗3)	300, 600, 1200, 2400,	9600,19200 bit/s ∗4)
	4800, 9600, 19200 bit/s
Communication method	Half-duplex
Synchro system	Synchronous communication method
	Stop bit: 1 bit/2 bit
	Parity: Not available/Available
Transmission format	(Odd number/Even number)
	Data length 7 bit/8 bit
	Beginning code: STX available/STX not available
	Ending code: CR/CR+LF/not available/ETX
Data output order	Starting from 0 bits per character
No. of connected units	Ñ	99 ∗5) ∗6)
	¥ General-purpose
Communication mode	communication
	¥ Computer link

∗1) When communicating between FP-e and other devices, it is recommneded to perform resend processing.

∗2) For RS232C wiring, be sure to use shielded wires for higher noise immunity.

∗3) Set the baud rate of RS485 with the FP-e system register and FP-e internal switch. Set the baud rate of RS232C with the FP-e system register.

∗4) When sending a command from the FP-e is completed in RS485 communication, send a response from the receiving device to the FP-e after the following time has elapsed: 9600 bit/s: 2 ms or longer 19200 bit/s: 1 ms or longer

It takes at least 1 scan time (at least 2 ms) for the FP-e to send back a response after received the command.

∗5) When our C-NET Adapter or RS485 device other than recommended is connected in the system, the maximum connection number is limited to 32 units.

∗6) For a RS485 converter on the computer side, SI-35 (from LINE EYE Co., Ltd.) is recommended.

When SI-35 is used in the system, up to 99 units can be connected.

19200 bit/s9600 bit/s

■ Dimensions (mm) ■ Wiring diagram

●Input connector

		(Standard type)		(Thermocouple input type)
		44.5			COM	COM				circuit
			COM		X0
			X1		X2					Internal
			X0		X1
			X2		X3	Xn
			X3		X4
			X4		X5
			X5	TC0	A0+
			X6		A0−	● Power supply/COM. port connector
			X7	TC1	A1+	(RS232C type)
					A1−					24 V DC	+
											−
		● Output connector								Ground
				(+)		COM. port		Send data (Output)			SD
			+		circuit			Receive data (Input)			RD
						(RS232C)
			−					Signal Ground			SG
48	70	L	Y0	Y0 to Y4	Internal	(RS485 type)
		L	Y1
	7.5	L	Y2	(−)		(Terminal station)				(Ordinary station)
	.	L	Y3			24 V DC			+	24 V DC	+
		L	Y4	Y5					−		−
					circuit
		L	YC			Ground				Ground
			Y5		Internal	(RS485)				(RS485)
		Power	COM
						COM. port				COM. port
				COM			Short		E		E

Clearwater Tech - Phone: 800.894.0412 - Fax: 208. 01/2004368.0415 - Web: www.clrwtr.com - Email: info@clrwtr.com 7