Panasonic BT-H1700AE manual Function Setting, Picture SUB ADJ

ITEM CONTENTS AND ADJUSTMENT RANGE/SETTINGS

1.FUNCTION SETTING

Selects the colour system and displays the monitor’s power-

up time or the total usage time. Press the button to display the setting menu illustrated on the right.

<FUNCTION SETTING>

COLOR SYSTEM	:AUTO
SYNC SELECT	:INT.
RUSH DELAY TIME	:STD.
TALLY SELECT	:GREEN
REMOTE SYSTEM	:MAKE
EMBEDDED	:1G
HOUR METER X100h	:000

EXIT: MENU ADJUST:-+ SELECT:

Item	: REMOTE SYSTEM
Settings	: MAKE/TRIGGER
Function	: Selects the contact system (MAKE (make

contact) or TRG. (trigger contact)) for the MAKE/ TRIGGER terminals.

MAKE (make contact system): Controls the

function by stable disconnection (terminal

open) or short-circuit (short with GND of 15th

terminal) of the controlled terminal.

ENGLISH

Item	: COLOR SYSTEM
Settings	: AUTO/NTSC/PAL
Function	: Selects the colour system when using the video
	input card.
	AUTO : Change NTSC and PAL automatically.
	NTSC : Keeps the colour system NTSC.
	PAL : Keeps the colour system PAL.

NOTE : Normally select AUTO. However, if the input signal is unstable, select NTSC or PAL.

Item	: SYNC SELECT
Settings	: INT./EXT.
Function	: Synchronised signal selection.

INT. : The input video signal is synchronised with the built-in sync signal.

EXT. : The input video signal is synchronised with an external signal from an external sync terminal.

*The external synchronised signal terminals apply to the HD/ CS terminal and VD terminal (in the RGB/COMPONENT Input Card), or the EXT. SYNC terminal (in the VIDEO Input Card).

*This item is not shown when only SDI and/or HD SDI input cards are installed.

Item	: RUSH DELAY TIME
Settings	: STD./SLOW
Function	: Sets the time when the power supply to the
	monitor’s circuits (excluding the micro computers)
	starts after the power switch is pressed.
	STD. : The power supply starts approx.
	1 second after the power switch is
	pressed.
	SLOW : The power supply starts approx.
	3.2 seconds after the power switch is
	pressed.

NOTE : If you are going to turn several Multi-Format Monitors on at the same time, it is recommended to apply SLOW to some of the monitors to control rush current.

Item	: TALLY SELECT
Settings	: GREEN/RED
Function	: Selects the colour of the tally lamp (when lit) on

the upper front panel.

GREEN: The tally lamp lights in green.

RED : The tally lamp lights in red.

NOTE : Set the MAKE/TRIGGER terminal’s tally control in the REMOTE (external control) terminal setup menu. For details, refer to Page 19. To set the color, use TALLY SELECT in the “FUNCTION SETTING” setup menu or MAKE/TRIGGER in the REMOTE (external control) terminal setup menu. For details, refer to Page 15 and 19.

TRG. (trigger system): Controls the function by

instantaneously (one second) short-circuiting

(short with GND of 15th terminal) the controlled

terminal.

Item

: EMBEDDED

Settings

: 1G/2G/1-2G

1G

: 1ch

2ch

3ch

4ch

1-2ch

3-4ch

1-4ch

2G

: 5ch

6ch

7ch

8ch

5-6ch

7-8ch

5-8ch

1-2G : 1ch

2ch

3ch

4ch

5ch

6ch

7ch

8ch

1-2ch

AUTO

5-8ch

1-4ch

7-8ch

5-6ch

3-4ch

Function

: Selects Embedded Audio signal channels.

NOTE : The auto setting mixes and outputs all 8 signal channels. Output level is automatically detected and set at FPGA

according to the channel numbers that are receiving signals.

* About sound output level

Sound output level is set to a standard output level for all channels when several sound channels are output at the same time. The more channels are selected, the lower each channel’s level will be.

(Each channel's level becomes half for 1– 2 channel, 1/4 for 1– 4 channel.)

*About AUTO

When AUTO is selected, the number of sound channels in use is detected. The level of each channel is automatically adjusted to ensure that the total sound output level is equiva- lent to the standard output level.

*This item is shown when an input card compliant with EM- BEDDED AUDIO is installed.

Item	: HOUR METER X100h
Number
range	: 000 ~ 655
Function	: Displays the total usage time of the monitor in
	hundred-hour units.

●When the timer passes 655, it returns to 000.

●The timer does not count the usage time under one hour.

2.PICTURE SUB ADJ.

Performs approximate

adjustments using the control		<PICTURE SUB ADJ.>
knobs on the front panel. Press		CONTRAST	: 00
the	button to display the	BRIGHT	: 00
		CHROMA	: 00
		PHASE	: 00
setting menu illustrated on the
		NTSC SETUP	: 00
		COMPO.LEVEL	:SMPTE
right.
		sub menu
		reset
NOTE : When the RGB signal		EXIT: MENU ADJUST:- + SELECT:
	is input, only
	CONTRAST and

BRIGHT are displayed. When the PAL signal is input, only CONTRAST, BRIGHT and CHROMA are displayed.

15