Panasonic AV-HS300G manual External interfaces, RS-422 connector, GPI connector

Page 51

6. External interfaces

This unit comes with RS-422, GPI and tally connectors to serve as external interfaces.

6-1. RS-422 connector

This enables the unit to be controlled by an editing controller AG-A850. Use it with the settings below.

Baud rate: 38400 bps

Parity: ODD

Stop bit: 1 bit

Pin assignment

Pin No.	Signal name	Description of signal
1	FRAME GROUND	Frame ground
2	TXD –	Send data (–)
3	RXD +	Receive data (+)
4	GROUND	Ground
5	NC	Not used
6	GROUND	Ground
7	TXD +	Send data (+)
8	RXD –	Receive data (–)
9	FRAME GROUND	Frame ground

The following lists the functions which can be controlled by AG-A850. (Compliant with the GVG protocol)

•Crosspoint switch

•Wipe pattern selection

•Transition mode (MIX/WIPE) selection

•Auto transition time setting

•Auto transition execution

If the [AUX] switch is pressed twice, the lamp of the switch will light up red.

While the lamp is lighted up red, control exercised from an external source can be canceled.

If the same switch is pressed twice again while its lamp is still lighted up red, the lamp is extinguished, and the control exercised from an external source is re‑established.

6-2. GPI connector

This enables auto take operations to be executed by an external device. Auto transitions are executed at the fall of the GPI signals.

The signals are input using contacts. The auto take operations are executed using these contacts as triggers.

Use an M3.5 stereo plug for connection with the main unit.

AUTO TAKE

AUTO TAKE

51

Image 51

Contents Operating Instructions FCC Note Safety precautionsImportant Safety Instructions For business users in the European Union Contents Description Features Handle carefully Precautions for use Power off before connecting or disconnecting cables  MaintenanceFunctions in each area  Power indicator Power Power switch Alarm indicator AlarmCrosspoint area  PGM/A bus crosspoint switches PGM/A 1 to PST/B bus crosspoint switches PST/B 1 to  Source selector switches Source SELECT/AUX, KEY-S, KEY-F3 Wipe areaTransition area  Rotary encoders F1 to F4 LCD menu area Fader lever  Bus tally LEDsRear panel connections area 11 Selecting the bus modeBasic operations Transitions 53/45*.& 6/*5 G Selecting the transition modeManual transition using the fader lever #,% 53/45*.& 6/*5 T G 4&$Wipe decorations border, soft effect WipeSelecting the wipe pattern Selecting the wipe direction643 6& 45 -6. ‰ ‰ ‰ Setting the border colorAdjusting the border color Operation Parameter Description of setting Setting rangeSelecting the key source signals KeySelecting the key source ‰ ‰ ‰ Setting the keyKey adjustments 51& */7 178 -*/ 0 0/ 0/ 0Selecting the fill color Selecting the key fill signals51& $0-3 #64 85 Selecting key fillKey decorations Adjusting the fill colorSetting the key edge 643 6& 45 -6. ‰ ‰ ‰Adjusting the edge color Adjusting the color background Color background$#% $0-3 85 */ */ */ */ */ %7 0 Freezing the input signals4503 69 .&. &9&$ Frame memoryTransition area Preset memory4503 ‰ $-314.& %4# Clear This is used to clear contents in the preset memorySetting the input signal frame synchronizer SetupSetting the input signals Setting the input signals in 1 toXGA Setting the DVI input signals IN60%& 4$- %* /03 SD/NTSC SD/PAL‰ ‰ ‰ AdjustmentSetting the output signals Types of output signalsSelecting the AUX signals HD/SD Selecting the video format03.5 J Q Q J J9154 4* #-, 915 Setting the crosspointsAssigning signals to the crosspoints 9154 Setting the crosspoint switching Switch Signal Description91548 5*. Sync Bbst Exec Bbad TRI INT Setting the sync signals0614 714 Adjusting the output signal phase3YSTEMSSTANDARD Phase adjustment setupNetwork settings Setting the IP addressSetting the subnet mask Setting the gatewaySetting the MAC address 44 #- 7/$ ## 0/ 0 0 0/ Other settingsSetting the ancillary data BB signal setup level&4 Status displaysInitialization 4554 7&3 / /- 1083 /0 1 /0Setting menu table Fill Type INV PVWADJ Clip Gain DensFmem MEM PsmemMode XPTDviin SetupSIG Mode Gain Mode ScalCkph Hpos Vpos Setup SYSVanc DviphSpecifications Image transmission functionsConnections How to install the program Operation Setting the IP addressStartup ExitTransmitting images from the unit Transmitting images to the unitExternal interfaces RS-422 connectorGPI connector Pin No Signal name Description of signalTally connector Example of tally connectionsAV-HS300G AV-HS300G ConnectionsExample where the optional HD analog board is used Unit inch mm AppearanceSpecifications Specifications and standard accessoriesOptional accessories Standard accessoriesDVI Appendix glossaryAUX AvdlPST GPIIRE PGMSDI Memo Memo Page Eastern Zone