Panasonic PT-AE900U manual Adjusting the position

Page 25

Adjusting the position

#Press the MENU button to display the menu screen.

$Select the “POSITION” menu from the main menu, and then press the ENTER button.

%Press the F or G button to select an item.

&Press the I or H button to adjust the value or change the setting. For items with selective setting or a bar scale, the individual adjustment screen will be displayed. Press the F or G button to switch the item. When the input signal is from a PC, first select “AUTO SETUP” and then press the ENTER button to initiate automatic positioning. If the optimum setting is not obtained when “AUTO SETUP” is carried out, adjust the other items.

NOTE:

BIf signals with a dot clock

frequency of 108 MHz or higher

are being input, interference

may not be completely

eliminated when the “DOT

CLOCK” and “CLOCK PHASE”

adjustments are carried out.

BWhen YPBPR signals are being

input, “CLOCK PHASE” can be

adjusted only when 1 125

Set to “OFF” when some letters or parts of a projected image not visible around the edges of the image.

KEYSTONE

When either the projector or the screen is tilted, the keystone distortion will affect the image. If the projected image contains keystone distortion, follow the procedures in the table to correct any keystone

When an S-VIDEO/VIDEO signal is being input

When a HDMI signal is being input

When a YPBPR signal is being input

When a PC signal is being input

Horizontal position (H-POSITION)

To move the picture to the left: I button

To move the picture to the right: H button

Vertical position (V-POSITION)

To move the picture down: I button

To move the picture up: H button

DOT CLOCK

(PC only)

Periodic striped pattern interference (noise) may occur when a striped pattern such as the one below is projected. If this happens, press the

Ior H button to adjust so that any such noise is minimised.

CLOCK PHASE

(PC/YPBPR only)

Adjust the “DOT CLOCK” setting first before carrying out this adjustment. Press the I or H button to adjust so that the noise level is least noticeable.

(1 080)/60i, 1 125 (1 080)/50i,

1 125 (1 080)/24p, 750

(720)/60p or 750 (720)/50p

signals are being input.

ASPECT

The aspect ratio can be selected. Refer to page 30 for details.

WSS

ON

When WSS (Wide Screen Signalling) is detected from PAL or 625i(576i) YPBPR signals, the aspect ratio will also be switched automatically.

OFF

WSS will not be detected from PAL or 625i(576i) YPBPR signals.

OVER SCAN

[525p (480p), 625p (576p),

1 125 (1 080)/60i, 1 125 (1 080)/50i,

1 125 (1 080)/24p, 750 (720)/60p and 750 (720)/50p signals for YPBPR and HDMI signals only]

distortion. (Vertical keystone distortion correction only.)

Picture

Operation

condition

 

 

Press the H

 

button.

 

 

 

Press the I

 

button.

 

 

NOTE:

BVertical keystone distortion can be corrected to ±30° of the angle of tilt. However, the greater the correction amount, the more the picture quality will deteriorate, and the harder it will become to achieve a good level of focus. To obtain the best picture quality, set up the projector and screen in such a way that the amount of keystone correction required is as minimal as possible.

BThe picture size will also change when correction of keystone distortion is carried out.

BThe ratio of length and width of an image may become incorrect depending on the amount of the keystone correction.

Adjustments and settings

48-ENGLISH

ENGLISH-49

Image 25
Contents Model No. PT-AE900U LCD ProjectorPreparation Dear Panasonic CustomerContents Precautions with regard to safety Do not look into the lens while the projector is being used Do not put your weight on this projectorDo not cover the air inlet port or the air outlet port Always disconnect all cables before moving the projectorBefore use AccessoriesLocation and function of each part Power input socket AC # Connector panel $ Air inlet portLamp unit cover Main Power switch pages 26 $ Hdmi in connectorProjector control panel Remote control unitProjection methods Setting-upProjector position Projection distancesSetting up range using the lens shift function Connecting to equipment compatible with Hdmi Connecting to video equipmentConnections StartedOperating range Connecting to computerTurning on the power #Press the Power button Turning off the powerPower indicator Projector statusSetting the aspect ratio Aspect Functions Press the PIC. Mode buttonPress the Light button Displaying the Picture menu Main Turning off the picture momentarily ShutterDisplaying the Advanced Menu UsefulCursor ProfileColor TintChange LOG Profile SaveDelete Menu screens On-screen menusMenu operation guide Returning a setting to the factory defaultAdjusting the picture TV-SYSTEM Signal ModeAdvanced Menu Memory SaveAdjusting the position Changing the display language Option settingsLamp Power OFF TimerAuto Search Back ColorLamp indicator Lamp indicator Temp indicatorRemedy Lamp unit replacement period Power OFF Lamp unit replacement procedureCleaning and maintenance Before calling for serviceRemote control unit SpecificationsOptions Appendix List of compatible signalsGeneral arrangement of the Color Management menu Control commands Using the Serial connectorPin assignments and signal names ConnectionProjection dimensions calculation methods DimensionsInquiry commands Cable specificationsTrademark acknowledgements