Specifications, Features | Phoenix Gold RSD300.1 specs

SPECIFICATIONS:

RSd 300.1

MONOBLOCK CLASS A/B POWER AMPLIFIER

CEA-2006 Compliant Ampliﬁer Power Standard

Frequency Response . . . . . . . . 10Hz to 300Hz

Effective Damping Factor . . . . . . 6.39 @ 4 ohms

Maximum Input . . . . . . . . . . 11.8V at clipping

Maximum Sensitivity . . . . . . . . 200mV at clipping

Ratings other than CEA-2006

Power Output . . . . . . . . . . . 360W RMS @ 2 Ohms, 100Hz and 1% THD+N Bass Boost . . . . . . . . . . . . +18dB @ 45Hz

Low Pass Filter Frequency Response. . 30 to 300Hz Lowpass, 18dB per octave Subsonic Filter Frequency Response . . 5 to 55Hz Highpass, 18dB per octave Dimensions (L x W x H): . . . . . . . 12 7/8” x 11 3/16” x 2 3/8”

RSd 600.1

MONOBLOCK CLASS D POWER AMPLIFIER

CEA-2006 Compliant Ampliﬁer Power Standard

Power Output . . . .	. . . .	.	. 400W RMS @ 4 ohms and 1% THD+N
Signal to Noise Ratio . .	. . . .	. . 82 dBA (reference: 1W output @ 4 ohms)
Frequency Response . .	. . . .	.	. 10Hz to 300Hz
Effective Damping Factor	. . . .	. . 6.39 @ 4 ohms
Maximum Input . . . .	. . . .	.	. 10V at clipping
Maximum Sensitivity . .	. . . .	.	. 200mV at clipping

Ratings other than CEA-2006

Power Output . . . . . . . . . . . 650W RMS @ 2 ohms, 100Hz and 1% THD+N Bass Boost . . . . . . . . . . . . +18dB @ 45Hz

Low Pass Filter Frequency Response. . 30 to 265Hz Lowpass, 18dB per octave Subsonic Filter Frequency Response . . 5 to 55Hz Highpass, 18dB per octave Dimensions (L x W x H): . . . . . . . 16 7/8” x 11 3/16” x 2 3/8”

Due to continual product improvement, all speciﬁcations subject to change without notice.

RSd AMPLIFIERS

MONOBLOCK OWNER’S MANUAL

FEATURES:

BUILT-IN ELECTRONIC CROSSOVER

Monoblock: 18dB per octave electronic crossover for low- pass and an 18dB per octave subsonic ﬁlter.

ON BOARD PROTECTION

The on-board protection circuitry monitors abnormal conditions such as voltage spikes, short circuit and over thermal limits. When any of these conditions exist, the protection circuit will shut down the ampliﬁer and light up the protection indicator to identify the problem. Once the problem is resolved, the ampliﬁer will return to normal operation automatically.

HIGH SPEED HIGH CURRENT MOSFET SWITCHING POWER SUPPLY

High current MOSFET transistors are used in the power supply section to minimize internal heat and maximize reliability.

HIGH CURRENT/HIGH VOLTAGE FULLY

COMPLEMENTARY OUTPUT STAGE

Complementary output stage audio circuitry has been a standard in high end home ampliﬁer design. Phoenix Gold is one of the very few car audio manufacturers to incorporate this design approach into a mobile audio ampliﬁer.

LINE OUTPUTS

The ampliﬁers full-range line outputs can be used to feed signals to another ampliﬁer for future expansion or for setting up a more sophisticated system.

WIDE RANGE INPUT SENSITIVITY ADJUSTMENT

The input sensitivity level of this ampliﬁer can be easily varied from as low as 200 mV to as high as 8.0 volts by adjusting the control on the Input Panel.

MULTI-FUNCTION PROTECTION INDICATOR

When the red protect indicator lights up it signiﬁes a high operating temperature is detected and the ampliﬁer is temporarily shut down to allow for a cooling period. As soon as the temperature returns to a safe level, the ampliﬁer will restart and resume normal operation. This indicator also lights up when the ampliﬁer detects either an over-current situation, shorted speaker outputs or a DC offset at the outputs.

Turn off the ampliﬁer; double-check all inputs and speaker connections to make sure there is no short or inappropriate input. If all connections are in order, turn on the ampliﬁer to resume operation.

VARIABLE BASS BOOST

The bass boost will increase the output centered at 45Hz from 0 to 18dB

Phoenix Gold International, Inc. • 9300 North Decatur St. Portland, OR 97203 • 503.286.9300 • www.phoenixgold.com