Panasonic PT-F100NTU manual Read this first, Minimum required setting screen

Page 12

Read this first

Minimum required setting screen

When you start the projection for the first time, the minimum required setting screen for projection will be displayed.

LANGUAGE

Select the required language setting.

Preparation

LANGUAGE

 

 

SELECT

 

ENTER

Press F G I H buttons of the Remote control or Control panel on the projector to highlight the required language, and press ENTER to proceed to the next setting.

OPTIONS

Select the current projection method and fan speed setting. If you need return to the previous setting, press the RETURTN button.

OPTION

INSTALLATION

FRONT/DESK

HIGHLAND

OFF

 

RETURN

SELECT

 

 

ENTER

INSTALLATION

Press I H buttons of the Remote control or Control panel on the projector to select the required installation method. Press G to proceed to the HIGHLAND setting.

FRONT/DESK

Setting on a desk/floor and

projecting from front

 

FRONT/CEILING

Mounting in the ceiling and

projecting from front

 

REAR/DESK

Setting on a desk/floor and

projecting from rear

 

REAR/CEILING

Mounting in the ceiling and

projecting from rear

 

HIGHLAND

If you use the projector at high elevation, the HIGHLAND setting need to be ON to set the fan speed high. Press I H to select the required option. If you need to return to the INSTALLATION, press F.

OFF

The fan speed is low.

ON

The fan speed is high.

NOTE:

•At 1 400 m (4 593 ft) above sea level, the setting must be ON.

•The loudness of fan noise depends on the HIGHLAND setting.

Press the ENTER button to start the projection.

Once you finish the minimum requirement setting, it will not be displayed again unless the projector is initialised. See “INITIALIZE ALL” on page 38.

You can change the settings from the MAIN MENU. See “Menu Navigation” on page 29.

ENGLISH - 12

Page 11 Page 13
Image 12
Page 11 Page 13
Contents PT-F100U Important Safety Notice Model number PT-F100NTU / PT-F100UImportant Safety Notice Declaration of ConformityModel Number PT-F100NTU / PT-F100U Trade Name PanasonicDeclaration of Conformity Declaration of Conformity DoCImportant Infomation Contents Settings MaintenanceAppendix Precautions with regard to safety Precautions with regard to safety Do not look into the lens while the projector is being usedLamp cover gets very hot, and touching it can cause burns Use only the specified batteriesRemove the used batteries from the remote control promptly Do not put your weight on this projectorDo not mix old and new batteries Electric shocks can result if this is not doneAccessories Minimum required setting screen Read this firstRemote control About Your ProjectorProjector body About Your ProjectorTop and front view Control panelAbout Your Projector Back and bottom view Computer. Selectable for inputOutput by menu operation Setting up Calculation methods for screen dimensionsScreen size and throw distance Projected imageFront leg adjusters and throwing angle Setting upProjection method Mounting in the ceiling and projecting from frontAdjusting the Lens shift lever Lens shift and positioningHorizontal shift Vertical shiftSetting up Projector location range When the screen position is fixedWhen the projector position is fixed Connecting with computers LAN cable RGB signal cableConnections Before connection to the projectorConnecting with AV equipment Connecting with Video IN/S-VIDEOConnecting with Component ConnectionsSwitching the projector on/off Power cordPower indicator Switching on the projector Switching off the projectorSwitching the projector on/off Switch the Main Power on Press the Power buttonSelecting the input signal Projecting an imagePositioning the image Focus lever Zoom leverRemote control operation Setting up the image position automaticallyOperating range Facing to the projectorSwitching the input signal Using the laser pointerResetting to the factory default settings Projecting an image in INDEX-WINDOW modeCapturing an image Stopping the projection temporaryControlling the volume of the speaker Enlarging the centered areaEnlarging the image Shifting the center pointAdjusting with the bar scale items Menu NavigationNavigating through the Menu Displaying the Main menuMain menu and Sub-menu Menu NavigationWEB Control Live Mode CUT Status Initialize Audio BalanceNetwork Standby Picture menu Detailed Setup For S-VIDEO/VIDEO signalsFor RGB signals Position menu When the Resizing is set to OFF ResizingFrame Lock Position menuOption menu Input GuideStartup Logo COMPUTER2 SelectPower OFF Timer Auto SetupDirect Power on Signal SearchHighland Closed CaptionTest Pattern CC2 TT1Input Password Password ChangeSecurity menu Text DisplayNetwork menu Items in Network menuNetwork menu, the following items are available TEMP, Lamp and ARF Indicators Managing the indicated problemsLamp indicator Temp indicatorCare and Replacement Cleaning the projectorReplacing the ARF Auto Rolling Filter Care and Replacement When to replace the Lamp unitReplacing the Lamp unit Before replacing the Lamp unitCeiling mount bracket safeguards Care and Replacement Replacement procedureInstalling the safety cable Removing and replacing the lamp unitTroubleshooting List of compatible signals Technical InformationQuality*2 Dots*1 KHz MHzSerial terminal Technical Information Cable specifications Control commandsComputer connection guidance ProjectorLamp switching Switching input SignalsInput signal Remote terminalSpecifications OUT AudioComputer Audio Variable AudioScreen size and throw distance for 169 aspect ratio Projection size 16 Throw distance LScreen height SH Screen width SW Minimum distance SW = SD x SH = SD x Unit m LW = 0.0332 x SD LT = 0.066 x SDDimensions Trademark acknowledgementsThese Operating Instructions are printed on recycled paper Index ALS Ambient Luminance Sensor ARF Auto Rolling FilterCalculation methods LeverIndex Avis important concernant la sécurité Numéro de modèle PT-F100NTU / PT-F100UNuméro de série Avis important concernant la sécurité AvertissementAdvertencia Déclaration de conformité Précautions de sécurité AvertissementMises EN Garde Précautions de sécuritéUtiliser uniquement les piles spécifiées Ne pas mélanger des piles usées et des piles neuvesSinon cela peut causer des chocs électriques Précautions lors de linstallation Précautions lors du transportPrécautions lors de lutilisation Remplacement de lunité de la lampe Délai de remplacement de lUnité de la lampe«LAMPE DE REMPLACEMENT» est Avant de remplacer le lUnité de la lampeRetirer et remplacer la lampe De lUnité de La lampeRemplacement de lunité de la lampe Installation du câble de sécuritéProtections du support de montage au plafond Panasonic Projector Systems Company Technical SupportProfessional/Industrial Video
Top Page Image Contents