Wiring the System

3.Strip 3/8" from the battery end of the power cable and crimp a large ring terminal to the cable. Use the ring terminal to connect to the battery pos- itive terminal. Do not install the fuse at this time.

4.Prepare a length of cable to be used for the ground connection. Strip 5/8" of insulation from the end of the cable as described above and con- nect to the appropriate terminal of the amplifier. Prepare the chassis ground by scraping any paint from the metal surface and thoroughly clean the area of all dirt and grease. Strip the other end of the wire and attach a ring connector. Fasten the cable to the chassis using a non- anodized screw and a star washer.

5.Prepare the REM turn-on wire for connection to the amplifier by stripping 1/4" of insulation from the wire end and crimping an insulated spade connector in place. Slide the connector over the REM terminal on the amplifier. Connect the other end of the REM wire to a switched 12 volt positive source. The switched signal is usually taken from the source units auto antenna or the accessory lead. If the source unit does not have these outputs available, the recommended solution is to wire a mechan- ical switch in line with a 12 volt source to activate the amplifier.

6.Securely mount the amplifier (with supplied screws) to the vehicle or amp rack. Be careful not to mount the amplifier on cardboard or plastic panels. Doing so may enable the screws to pull out from the panel due to road vibrations or sudden vehicle stops.

7.Determine the number of inputs needed to drive the amplifier and move the input switch to the desired setting (Power 400 & Power 800 4-chan- nel amplifiers only.).

8.Connect the source signal to the amplifier by plugging the RCA cables into the input jack(s) at the amplifier.

9.Connect the speakers. Strip the speaker wires 5/8" and insert into the appropriate terminal on the amplifier. Insert the bare wire into the speak- er terminal and tighten the set screw to secure into place. Be sure to maintain proper speaker polarity. DO NOT chassis ground any of the speaker leads, as unstable operation may result.

10.Perform a final check of the completed system wiring to ensure that all connections are accurate. Check all power and ground connections for frayed wires and loose connections which could cause problems from road vibrations.

11.When bridging two BD110001/BD15001 units you must use the BDSYNC cable, available at your local dealer. The speaker grounds of both units must be joined using an 8 gauge wire that is no longer than 15”.

bd500.1, bd1000.1, bd1500.1 specifications

Rockford Fosgate is a name synonymous with high-performance audio systems, particularly in the world of car audio. Among its impressive lineup, the bd series of amplifiers stands out for enthusiasts looking to bathe their vehicles in rich, powerful sound. The bd500.1, bd1000.1, and bd1500.1 amplifiers are specifically engineered to provide uncompromising power and clarity, catering to diverse auditory preferences.

Starting with the bd500.1, this model is perfect for those seeking robust performance without overwhelming power demands. It delivers a remarkable 500 watts RMS at 1 ohm, ensuring that even the most demanding subwoofers receive sufficient power for optimal performance. The Smart Engage System allows for a seamless integration with factory audio systems, enhancing versatility in installation. It also features a built-in frequency filter, enabling users to customize their sound experience further.

Moving on to the bd1000.1, this amplifier takes performance to the next level. With an impressive 1000 watts RMS at 1 ohm, it is designed to handle larger setups efficiently. The bd1000.1 incorporates the same Smart Engage System, making it easy to hook up to various audio configurations. Additionally, it boasts an advanced gain control system, which helps in minimization of distortion and ensures clear, powerful bass. The Dynamic Thermal Management technology is another highlight, keeping the amplifier at an optimal operating temperature and preventing overheating during extended use.

Lastly, the bd1500.1 is a titan in the bd series, delivering a staggering 1500 watts RMS at 1 ohm. This amplifier is tailored for those who desire the ultimate in bass performance, capable of driving larger subwoofers and high-output systems. The bd1500.1 features an advanced circuit design, maximizing efficiency while reducing heat buildup. The integrated bass boost EQ adjusts low frequencies to suit personal tastes, while the low-pass crossover allows for precise tuning of the audio output.

All three models come equipped with Rockford Fosgate’s signature Punch EQ, ensuring that users can tailor their listening experience to their liking. Each of these amplifiers is built with high-quality components, emphasizing durability and longevity against varying environmental conditions. From the bd500.1 to the bd1500.1, Rockford Fosgate continues to push the boundaries of car audio, ensuring that enthusiasts can enjoy their favorite music with unrivaled power and clarity. Whether you’re a casual listener or a dedicated audiophile, these amplifiers are designed to elevate your audio experience to new heights.