Rockford Fosgate Essential Installation Considerations for Your Amplifier
Page 9

Installation Considerations

This section focuses on some of the vehicle considerations for installing your new Punch amplifier. Checking your battery and present sound sys- tem, as well as pre-planning your system layout and best wiring routes, will save installation time. When deciding how to lay out your new system, be sure that each component will be easily accessible for making adjustments.

Before beginning any installation, be sure to follow these simple rules:

1.Be sure to carefully read and understand the instructions before at- tempting to install the amplifier.

2.For safety, disconnect the negative lead from the battery prior to begin- ning the installation.

3.For easier assembly, we suggest you run all wires prior to mounting your amplifier in place.

4.Route all of the RCA cables close together and away from any high cur- rent wires.

5.Use high quality connectors for a reliable installation and to minimize signal or power loss.

6.Think before you drill! Be careful not to cut or drill into gas tanks, fuel lines, brake or hydraulic lines, vacuum lines or electrical wiring when working on any vehicle.

7.Never run wires underneath the vehicle. Running the wires inside the vehicle provides the best protection.

8.Avoid running wires over or through sharp edges. Use rubber or plas- tic grommets to protect any wires routed through metal, especially the firewall.

9.ALWAYS protect the battery and electrical system from damage with proper fusing. Install a fuseholder and appropriate fuse on the +12V power wire within 18” (46 cm) of the battery terminal.

10.When grounding to the chassis of the vehicle, scrape all paint from the metal to ensure a good, clean ground connection. Grounding connec- tions should be as short as possible and always be connected to metal that is welded to the main body, or chassis, of the vehicle.

6

Page 8 Page 10
Image 9
Page 8 Page 10
Contents Power bd1500.1 Power bd1000.1 Power bd500.1 Practice Safe Sound Table of Contents Specifications System Model Bd500.1 Bd1000.1 Bd1500.1Input Impedance Introduction Amplifier Accessory PackCircuitry Power Mono Amplifier Feature ChartDesign FeatureS Design Features Cont’d Installation Considerations Trunk Mounting Mounting LocationPassenger Compartment Mounting Engine Compartment MountingWiring the System Battery and ChargingWiring the System Power Connections Mono Mode InstallationPunch Bass Operation Crossover OperationPass-Thru Bridging Mode use bd sync kit Procedure 1 Check Amplifier for proper connections TroubleshootingLength of Warranty Limited Warranty InformationMontaje en el Malatero International InformationMontaje en el Compartimento de Pasajeros InstalacionTerminal GND Terminal B+Terminal REM Funcionamiento MonoInstallation Montage dans le coffreMontage dans lhabitacle Opération mono Im Fahrzeugkofferraum Auf der BeifahrerseiteEinbau GND Anschlub + AnschlubREM Anschlub Mono OperationInstallazione Nel BagagliaioNellabitacolo Terminale B+ cavo positivo Terminale GND cavo negativoTerminale REM Consenso di accensione Page Made in the USA

bd500.1, bd1000.1, bd1500.1 specifications

Rockford Fosgate is a name synonymous with high-performance audio systems, particularly in the world of car audio. Among its impressive lineup, the bd series of amplifiers stands out for enthusiasts looking to bathe their vehicles in rich, powerful sound. The bd500.1, bd1000.1, and bd1500.1 amplifiers are specifically engineered to provide uncompromising power and clarity, catering to diverse auditory preferences.

Starting with the bd500.1, this model is perfect for those seeking robust performance without overwhelming power demands. It delivers a remarkable 500 watts RMS at 1 ohm, ensuring that even the most demanding subwoofers receive sufficient power for optimal performance. The Smart Engage System allows for a seamless integration with factory audio systems, enhancing versatility in installation. It also features a built-in frequency filter, enabling users to customize their sound experience further.

Moving on to the bd1000.1, this amplifier takes performance to the next level. With an impressive 1000 watts RMS at 1 ohm, it is designed to handle larger setups efficiently. The bd1000.1 incorporates the same Smart Engage System, making it easy to hook up to various audio configurations. Additionally, it boasts an advanced gain control system, which helps in minimization of distortion and ensures clear, powerful bass. The Dynamic Thermal Management technology is another highlight, keeping the amplifier at an optimal operating temperature and preventing overheating during extended use.

Lastly, the bd1500.1 is a titan in the bd series, delivering a staggering 1500 watts RMS at 1 ohm. This amplifier is tailored for those who desire the ultimate in bass performance, capable of driving larger subwoofers and high-output systems. The bd1500.1 features an advanced circuit design, maximizing efficiency while reducing heat buildup. The integrated bass boost EQ adjusts low frequencies to suit personal tastes, while the low-pass crossover allows for precise tuning of the audio output.

All three models come equipped with Rockford Fosgate’s signature Punch EQ, ensuring that users can tailor their listening experience to their liking. Each of these amplifiers is built with high-quality components, emphasizing durability and longevity against varying environmental conditions. From the bd500.1 to the bd1500.1, Rockford Fosgate continues to push the boundaries of car audio, ensuring that enthusiasts can enjoy their favorite music with unrivaled power and clarity. Whether you’re a casual listener or a dedicated audiophile, these amplifiers are designed to elevate your audio experience to new heights.
Top Page Image Contents