Nortel Networks 10292FA, 10396EA manual Cabling an eight-channel Cwdm Omux

Page 42

42Chapter 3 Installing the shelf, OADM, and OMUX

Note: The CWDM GBIC wavelength must match the CWDM OMUX-4 equipment connector wavelength.

The TX of one device must always connect to the RX of the next device.

4Make the following network backbone connections (Figure 17):

Connect the network backbone east fiber optic cables to the east (left) CWDM OMUX-4.

Connect the network backbone west fiber optic cables to the west (right) CWDM OMUX-4.

Cabling an eight-channel CWDM OMUX

This section describes how to cable the following:

CWDM GBIC to a CWDM OMUX-8 ( Figure 18)

CWDM OMUX-8 to network backbone interfaces ( Figure 18)

Note: The CWDM OMUX-8 located on the left side of the chassis terminates the east network backbone connection. The CWDM OMUX-8 on the right side of the chassis terminates the west network backbone connection. See Figure 18.

To connect a CWDM OMUX-8:

1Install the CWDM GBICs (wavelength specific) into the network device(s). To install a CWDM GBIC, see Installing CWDM Gigabit Interface Converters, part number 212256-B.

2Clean all fiber optic connectors on the cabling (see “Handling and cleaning fiber optic equipment” on page 49 ).

3Connect the fiber optic cables from the CWDM GBIC TX and RX connectors to the CWDM OMUX-8 RX and TX connectors (Figure 18).

Note: The wavelength of the CWDM GBIC must match the wavelength of the CWDM OMUX-8 equipment connector.

212257-B

Image 42
Contents Installation and Networking Guidelines for Optical Routing Copyright 2002 Nortel Networks 212257-BInstallation and Networking Guidelines for Optical Routing Canada requirements onlyNortel Networks Inc. software license agreement Installation and Networking Guidelines for Optical Routing 212257-B Contents Chapter Installing the shelf, OADM, and Omux ContentsFigures Figures 212257-B Tables Tables 212257-B Preface Component FunctionBefore you begin Hard-copy technical manualsPreface How to get help Technical Solutions Center TelephonePreface 212257-B Chapter Describing the optical routing system Wavelength division multiplexingDescribing the optical routing system Parts of the optical routing systemGigabit interface converter description Parts of the optical routing systemOptical add drop multiplexer description Cwdm Gbic transceiver and labelNetwork add/drop ring application Cwdm Oadm network and equipment side connectionsCwdm Oadm ring configuration example Optical multiplexer/demultiplexer descriptionCwdm OMUX-4 Cwdm Omux in a point-to-point application Cwdm OMUX-8 network and equipment side connectionsCwdm Omux point-to-point configuration example Cwdm Omux in a ring applicationCwdm Omux ring configuration example Describing the optical routing system 212257-B Chapter Calculating transmission distance About transmission distance and optical link budgetHow to calculate expected loss budget How to calculate maximum transmission distanceCalculating transmission distance Point-to-point network configuration example Point-to-point transmission distancePoint-to-point signal loss values Mesh ring transmission distancePoint-to-point maximum transmission distance calculations Mesh ring network configuration Mesh ring signal loss values Mesh ring maximum transmission distance calculationsHub and spoke network configuration Hub and spoke transmission distanceHub and spoke signal loss values Hub and spoke maximum transmission distance calculationsChapter Installing the shelf, OADM, and Omux Preparing for installationExceeding class 1 power level warning Installing the shelf, OADM, and Omux Environmental and physical requirementsElectrostatic discharge Installing the shelf Inserting a Cwdm Oadm or a Cwdm Omux Shelf with plug-in module in 19-inch rackCabling a Cwdm Oadm or a Cwdm Omux Cabling a Cwdm OadmCabling a Cwdm Oadm Cabling a four-channel Cwdm Omux Cabling a Cwdm OMUX-4Cabling an eight-channel Cwdm Omux Cabling an Cwdm OMUX-8 Removing a Cwdm Oadm or a Cwdm Omux Appendix a Cwdm Oadm specifications Cwdm Oadm specificationsAppendix a Cwdm Oadm specifications 212257-B Cwdm Omux specifications Cwdm Omux specificationsAppendix B Appendix B Cwdm Omux specifications 212257-B Appendix C Handling and cleaning fiber optic equipment PrecautionsCleaning Fiber Optic Connectors Appendix C Handling and cleaning fiber optic equipmentTools and Materials Cleaning Single SC and FC Connectors Cleaning Duplex SC Connectors Cleaning Receptacle or Duplex Devices Page Glossary Glossary Dwdm See optical fiber Group of circuits connected at one point on a network See MMF Ndsf An optical wavelength band for WDM optical communications Device that does not require a source of energy to function See SMF WDM Glossary 212257-B Index Cwdm OmuxIndex OMUX, CwdmIndex Index 212257-B