Rockford Fosgate 250.1 manual N F O R M A T I O N

Page 53

										A	L
									N	A
								O	N
							I	O
							I
						A	T
					N	A
				R	N
			E	R
		T	E
	N	T
I	N
I

I

N

F

O

R

M

A

T

I

O

N

– 50 –

Image 53

Contents power powerpower 250.1PRACTICE SAFE SOUND G E T T I N G S T A R T E D TA B L E O F CO N T E N T SPunch Power Punch PowerINTRODUCTION TO 250 SERIES DIABLO Dynamically Invariant A-BLinear Operation TECHNICAL DESIGN FEATURESTOPAZ Tracking Operation Pre-AmplifierZone trans nova circuitryXCard Internal Crossover Stereo Pass-ThruDSM Discrete Surface Mount Technology ITS Increased Thermal Stability Balanced Line InputsNOMAD NOn-MultiplyingAdvanced Decision 250.2 DE S I G N FE AT U R E S PLIFIER 250.1 DE S I G N FE AT U R E S 1AMPLIFIER Tools Needed INSTALLATION CONSIDERATIONSTrunk Mounting BATTERY AND CHARGINGPassenger Compartment Mounting Engine Compartment MountingW I R I N G T H E S Y S T E M USING PASSIVE CROSSOVERS 6 dB/Octave High-Pass TABLE OF CROSSOVER COMPONENT VALUES6 dB/Octave Low-Pass FreqCU S T O M I Z I N G T H E XCA R D US I N G T H E XCARDHigh-Pass Low-PassButterworth Alignment Q = XCA R D RESISTOR CHART1% resistors used with 0.047∝ F capacitors Butterworth Alignment Q =250.2 Power Connections Option #2 250.2 INSTALLATION250.2 Power Connections Option #1 Stereo/Mono Operation Stereo OperationLeft Phase Switch set to Right Phase Switch set toEZ-BridgedOperation Bridged OperationLeft Phase Switch set to Right Phase Switch set toPage XCard not required Pass-Thru uses output from XCard 250.2 uses output from XCardPage Configurea24dBperoctave and“AudiophileBypass”the Configurea12dBperfilterfor Pass-ThruConnecting the BLT USING THE 250.2 BALANCED LINE INPUTS8.0 VAC Level Setting the BLTPerformance Characteristics Disconnect Speakers from the250.1 Power Connections Option #2 250.1 INSTALLATION250.1 Power Connections Option #1 minimum Mono OperationPhase Switch set to orFullRange AmplifiersPowerImpedanceforbridgedchannelshouldbe4Ω minimum Stereo/Mono OperationImpedanceforeachstereochannelshouldbe2Ω minimum minimum Bridged Mono OperationImpedanceforbridgedchannelshouldbe4Ω Pass,-High -LoworPass RangeFull“Audiophile Bypass” the U S I N G T H E 250.1 SIGNALS W I T C H I N G N E T W O R K XCard Configure a 12dB per octave filter for theLOUD TUNEConfigure a 24dB per octave filter for the Total Power Delivery RMS SY S T E M DI A G R A M S250 Watt System rated @ 4 ohms Total Power Delivery RMS 500 Watt System rated @ 4 ohmsTotal Power Delivery RMS 750 Watt System rated @ 4 ohmsTweeters 450 WattsTotal Power Delivery RMS 1000 Watt System rated @ 4 ohmsTweeters WattsBalanced Line Transmitter FG-BLT ROCKFORD FOSGATE ACCESSORIESNOISE Punch Status Display connected to one Punch Status Display FG-PSDChannel A monitors left channel Channel B monitors right channelEnergy Storage Capacitors punchXCard Crossovers 1.0capTR O U B L E S H O O T I N G SymptomDiagnosis RemedyDiagnosis SymptomRemedy Speaker Output LowDiagnosis SymptomRemedy Low or distorted output fromAUTOSOUND 2000s QUICK CHECK FOR TROUBLESHOOTING CAR AUDIO SYSTEMSPreface Noise OverviewSummation Time for ProcessorsAbout the Dynamic Power Measurements DY N A M I C PO W E R ME A S U R E M E N T SWhat is an Amplifier? MusicSpecifications subject to change without notice 250.2 SP E C I F I C AT I O N S180Watts 310Watts 620Watts 125Watts 225Watts 450 WattsSpecifications subject to change without notice 250.1 SP E C I F I C AT I O N S420Watts 710Watts 1420 Watts 250Watts 500 Watts 1000 WattsLength of Warranty LIMITED WA R R A N T Y IN F O R M AT I O NWhat is Covered What is Not CoveredN F O R M A T I O N UBICACIÓN DE LOS AMPLIFICADORES INTRODUCCIÓNMaletero HabitáculoOperación mono/estéreo INTRODUCTION InstallationMONTAGE Montage dans le coffrePage EINBAUORT EINLEITUNGDEUTSCH Im FahrzeugkofferraumStereo/Mono Betrieb Linken Phasen Schalter auf 0 stellenINTRODUZIONE InstallazioneDOVE POSIZIONARLO ITALIANOFase sinistra dellinterruttore posizionata su Stereo/Mono OperationMADE IN THE USA