Rockford Fosgate 5.3x manual 3X Specifications, Front/Rear Sub Channels

Page 40

5.3X SPECIFICATIONS

		Front/Rear	Sub
		Channels	Channel
Dynamic Power Rating (IHF 202 Standard)
Measured at 14.4 Voltage
Per channel into a 4Ω Load	40 Watts x 4
Per channel into a 2Ω Load	65 Watts x 4
Bridged Mono into a 4Ω Load	130 Watts x 2		130 Watts x 1
Continuous Power Rating (Competition Standard)
Measured at 14.4 Battery Voltage
RMS continuous power per channel,	30 Watts x 4
all channels driven into a 4Ω load from
20 to 20,000 Hz, with less than 0.30%
Total Harmonic Distortion (THD)
RMS continuous power per channel,	55 Watts x 4
all channels driven into a 2Ω load from
20 to 20,000 Hz, with less than 0.50%
Total Harmonic Distortion (THD)
RMS continuous power bridged/mono	110 Watts x 2		110 Watts x 1
into a 4Ω load from 20 to 20,000 Hz
with less than 0.50% Total Harmonic Distortion (THD)
Signal-to-Noise Ratio	>100dB (A-weighted)
Bandwidth	10 Hz to 250kHz ± 3dB
Damping Factor @ 4Ω	>200
Frequency Response	20 Hz to 20 kHz ± 0.5dB
Slew Rate	30Vμs
IM Distortion (IHF)	<0.05%
Input Impedance	20,000 ohms
Input Voltage	Variable from 325mV to 5.5volts
(Low level in-RCA)
	Variable from 850mV to 15 volts

(High level in-BTL)

Variable from 425mV to 7.5 volts

(High level in – Single Ended)

– 37 –

Image 40

Contents Installation a n d O p e r a t i o n Channel w/crossoversPractice Safe Sound TA B L E O F CO N T E N T S T T I N G S T a R T E DTechnical Design Features Accessory PackT R O D U C T I O N Mosfet Devices DSM Discrete Surface Mount Technology High Level Inputs 3X DE S I G N FE AT U R E S Power/Speaker Barrier Strip LED Power IndicatorSignal Input Switches Dual Extruded HeatsinksS TA L L AT I O N CO N S I D E R AT I O N S Mounting Location Trunk MountingBattery and Charging WI R I N G T H E SY S T E MCut Using Passive Crossovers Table of Crossover Component Values OhmsUS I N G T H E Xcard Customizing the XcardResistor Chart Butterworth Alignment Q =Xcard Access Using the Signal Switching Network Configuration #2Configuration #3 Front inputsConfiguration #6 Configuration #5Front inputs = Front, Rear Subwoofer outputs Configuration #1 Front inputs Subwoofer L Mono inputsConfiguration #2 Front inputs Factory Configuration #4 Mono Sub Input Front inputs Subwoofer L Mono inputsConfiguration #5 Front inputs Watts Total Power 3X Installation High Level Input Single Ended TypeHigh Level Input B.T.L. Type Factory Radio 100.7Power Connections Channel OperationChannel Mono Operation Sub Gain Control operates independentlySystem Diagrams Step #1Step #2 Step #3 Step #4 Front XCardSymptom Diagnosis Remedy TR O U B L E S H O O T I N GSpeaker Output Engine noise with About the Dynamic Power Measurements DY N a M I C PO W E R ME a S U R E M E N T SMusic Listening to Loudspeakers Not ResistorsWhat is an Amplifier? Information Cubed3X Specifications Front/Rear Sub ChannelsATC Length of Warranty Limited WA R R a N T Y in F O R M AT I O NPage Introducción Utilizacion DEL Circuito DE Conmutacion DE SeñalConfiguración n3 Configuración n5Configuración n6 PosterioresUtilisation DU Réseau DE Commutation DU Signal Somme avant & arrière ArrièreBenutzen DES Signal Netzwerkes EinleitungBeispiel #3 Beispiel #5Beispiel #6 Vordere Eingänge = Vordere & HintereIntroduzione Configurazione #2Impiegare LA Rete DI Selezione Degli Ingressi Configurazione Configurazione #4 Ingresso sub monoIngressi anteriore Posteriore sommatiMade in the USA