RCA RMB-167 manual Warranty

Page 4

WARRANTY

RIGEL CORPORATION - CUSTOMER AGREEMENT

1.Return Policy. This return policy applies only if you purchased the RMB-167 evaluation board directly from Rigel Corporation. If you purchase the board from a distributor please contact them for their return policy.

If you are not satisfied with the items purchased, prior to usage, you may return them to Rigel Corporation within thirty (30) days of your receipt of same and receive a full refund from Rigel Corporation. You will be responsible for shipping costs. Please call (904) 373-4629 prior to shipping. A refund will not be given if the READS package has been opened.

2.Limited Warranty. Rigel Corporation warrants, for a period of sixty (60) days from your receipt, that READS disk(s), hardware assembled boards and hardware unassembled components shall be free of substantial errors or defects in material and workmanship which will materially interfere with the proper operation of the items purchased. If you believe such an error or defect exists, please call Rigel Corporation at (904) 373-4629 to see whether such error or defect may be corrected, prior to returning items to Rigel Corporation. Rigel Corporation will repair or replace, at its sole discretion, any defective items, at no cost to you, and the foregoing shall constitute your sole and exclusive remedy in the event of any defects in material or workmanship.

THE LIMITED WARRANTIES SET FORTH HEREIN ARE IN LIEU OF ALL OTHER WARRANTIES, EXPRESSED OR IMPLIED, INCLUDING, BUT NOT LIMITED TO, THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE.

YOU ASSUME ALL RISKS AND LIABILITY FROM OPERATION OF ITEMS PURCHASED AND RIGEL CORPORATION SHALL IN NO EVENT BE LIABLE FOR DAMAGES CAUSED BY USE OR PERFORMANCE, FOR LOSS PROFITS, PERSONAL INJURY OR FOR ANY OTHER INCIDENTAL OR CONSEQUENTIAL DAMAGES. RIGEL CORPORATION’S LIABILITY SHALL NOT EXCEED THE COST OF REPAIR OR REPLACEMENT OF DEFECTIVE ITEMS.

IF THE FOREGOING LIMITATIONS ON LIABILITY ARE UNACCEPTABLE TO YOU, YOU SHOULD RETURN ALL ITEMS PURCHASED TO YOUR SUPPLIER.

3.READS166 (referred to as simply READS) License. The READS166 or the READS166 DEMO is hereby licensed to you on a non-exclusive basis for use in only one computer system and shall remain the property of Rigel Corporation for purposes of utilization and resale. You acknowledge you may not duplicate the READS for use in additional computers, nor may you modify, disassemble, translate, sub-license, rent or transfer electronically READS from one computer to another, or make it available through a timesharing service or network of computers. Rigel Corporation maintains all proprietary rights in and to READS for purposes of sale and resale or license and re-license.

BY BREAKING THE SEAL AND OTHERWISE OPENING THE READS PACKAGE, YOU INDICATE YOUR ACCEPTANCE OF THIS LICENSE AGREEMENT, AS WELL AS ALL OTHER PROVISIONS CONTAINED HEREIN.

4.Board Kit. If you are purchasing a board kit, you are assumed to have the skill and knowledge necessary to properly assemble same. Please inspect all components and review accompanying instructions. If instructions are unclear, please return the kit unassembled for a full refund or, if you prefer, Rigel Corporation will assemble the kit for a fee of $30.00. You shall be responsible for shipping costs. The foregoing shall apply only where the kit is unassembled. In the event the kit is partially assembled, a refund will not be available, however, Rigel Corporation can, upon request, complete assembly for a fee based on an hourly rate of $50.00. Although Rigel Corporation will replace any defective parts, it shall not be responsible for malfunctions due to errors in assembly. If you encounter problems with assembly, please call Rigel Corporation at (904) 373-4629 for advice and instruction. In the event a problem cannot be resolved by telephone, Rigel Corporation will perform repair work, upon request, at the foregoing rate of $50.00 per hour.

5.Governing Law. This agreement and all rights of the respective parties shall be governed by the laws of the State of Florida.

Image 4
Contents USER’S Guide Page Page Warranty Table Of Contents 10.1.1 Hardware READS166 Evaluation Software OverviewParts List Software Installation, READS166 SoftwareSystem Requirements Third Party SoftwareConnections, Jumper Settings START-UPSoftware Initialization Serial NumberBootstrapping Verifying that the Monitor is Loaded A D S C O M M a N D STroubleshooting Hardware Set-upSoftware Set-up PC set-upPower Operating NotesSerial port Jumper SelectionMemory Options RAM Memory OptionsEprom Memory Options Alternate Memory Map with Eprom in Low MemoryMoving RMON167 to Eprom Eprom CFG1Rstisr Syscon is 89h on the 167 dw 089E6h Dw 0F800h Nop Mov GAL Equations Default GAL Equations1 U1 Equations U2 Equations Alternate GAL Equations1 U1 Equations For Eprom In Low Memory 2 U2 Equations For Eprom In Low Memory Equations JP6 System Header Signal Pins SignalHeaders and Jumpers System and I / O HeadersJP7 Input/Output Header Signal 166 JP2 JP7Pins JP8 Extra Input/Output Header of the RMB-167 SignalSignal RMB-167 Analog-to-Digital Converter Reference Jumpers Bootstrapping S0RIRDiswdt Einit Mov R1, #0A55Ah Minimal Monitor Port Configuration MON167 MonitorDownload HEX file HelpPort Data Word MemoryREADS166 Version READS166 V3.00 ConceptsArchive Projects Executable ProjectsModule Circuit Diagrams