APC BU154A, UTS10BI, UTS6H Circuit Status Verification, Circuit Configuration and Setup

Page 11

UPS Power Rating

Once the BACKUP2 SOURCE TYPE has been selected, that source type will

 

 

 

 

 

 

appear in the power rating display message. Use the down/up arrow keys to set the

UPS POWER RATING:

 

correct power rating for the backup2 power source connected to the UTS.

0-1800 WATTS

 

There are three levels for rapid rating increment changes. Press and hold the down or

up arrow key to adjust the power rating and to move through the three levels described here. To revert back to level 1 release the down arrow key then press and hold the down arrow key.

Level 1 increases or decreases the rating by 5 Watts. Level 2 increases or decreases the rating by 10 Watts. Level 3 increases or decreases the rating by 100 Watts.

UPS Surge Overload Time

Once the BACKUP2 SOURCE TYPE has been selected, that source type will

 

 

 

 

 

 

appear in the surge overload time display message. Use the down/up arrow keys to

UPS SRGE OVRLD TIME:

 

set the desired ALM response time.

0-60 SEC

 

When power output exceeds the pre-set power rating for the Backup21 Source (see

UPS Power Rating above), this feature determines the time it will take for ALM to respond and activate load shedding process.

Low UPS surge overload time settings decrease the possibility of a generator overload condition while increasing the possibility that ALM will activate load shedding.

High UPS surge overload time settings increase the possibility of a generator overload condition while decreasing the possibility the ALM will activate load shedding.

Reset to Factory Default

Use the down/up arrow keys to select YES. This will reset all configurable parameters to the factory default settings.

Selecting YES will also start the UTS Setup Wizard described in the Site Preparation and Installation Guide supplied with this unit.

RESET TO DEFAULT: NO

Circuit Status Verification

The status of each circuit on the UTS can be viewed by pressing the Circuit Status button located on the front of the UTS. To navigate through the circuits, press the Circuit Status button after viewing the status of each circuit.

CK1SRC (circuit1 source) indicates the power source (utility power), plus the status of circuit1: number of Amps, number of kWh, and number of Watts.

Circuit Configuration and Setup

CK1SRC: UTILITY AMP: 1

KWH: 2:35 WATTS: 120

Circuit setup

Press the Circuit Setup button located on the front of the UTS to enter circuit setup mode and to navigate through the circuit setup options. Circuit setup begins with circuit 1 and proceeds through all of the configuration options for circuit 1 before moving on to circuit 2. The same is true for circuit 2, then circuit 3 and so on.

Use the down/up arrow buttons to navigate through the configuration options and to change values displayed on the LCD.

Note: The settings and values selected will change immediately after an arrow button is pressed.

The LCD will revert back to the starting display message after 30 seconds with no activity.

To configure a specific circuit, press the Circuit Status button until the display shows the desired circuit, then press the Circuit Setup button. The LCD will display the first setup option for the selected circuit.

10

Operation Manual Universal Transfer Switch UTS6 UTS6H UTS6BI UTS10BI

Page 10 Page 12
Image 11
Page 10 Page 12
Contents Universal Transfer Switch Protect your investment IntroductionAbout this product Safety Precautions Safety and Regulatory Information save this informationUTS Configurable Features UPS UTS Controls and IndicatorsLCD UPS Inlet UTS Power ConnectorsUTS circuit LED configurations Generator Inlet GuideUTS FW VER UI FW VER Utility PHASE1 Utility PHASE2 System Load 2400WSystem Status Verification Load Shedding System Configuration and SetupSystem setup Bypass ModeTime Management Reset Energy MeterBackup1 Source Type Backup1 Generator Power RatingBACKUP2 Source Type Generator Start ModeBackup2 Source Type Circuit Status Verification Circuit Configuration and SetupDelayable Circuits Circuit setup optionsSetup Option 1-Circuit Load Type Setup Option 2-SourceCircuit Amp Rating Circuit Security ModeCircuit Maximum Time Off and Minimum Time On Severe low voltage conditions TroubleshootingRequires the services of a qualified electrician Backup2 Power Source is setProblem The LCD displays the message Rating requires the services of a qualified electricianRadio Frequency Warnings ServiceAPC Worldwide Customer Support Regulatory InformationTerms of warranty Two-Year Warranty990-2993C 2010
Related manuals
Manual 30 pages 5.68 Kb

BU154A, UTS6H, UTS10BI, UTS6 specifications

The APC UTS6, UTS6H, UTS10BI, and BU154A are prominent products in the field of connectivity and power management, specifically designed to enhance the efficiency and reliability of electrical systems. Each of these models carries unique features and characteristics that cater to diverse applications in both residential and industrial environments.

The APC UTS6 is a highly versatile surge protector designed for home and office setups. It provides essential protection against voltage spikes and electrical surges, which can damage connected devices. The UTS6 features six outlets, allowing multiple devices to be connected simultaneously. It incorporates a built-in circuit breaker and LED indicators for surge protection status, ensuring that users are informed about the operational status of their equipment. Its compact design makes it ideal for tight spaces, and its robust construction ensures long-term durability.

The UTS6H is an enhanced version of the UTS6, tailored specifically for high-capacity devices. This model is particularly useful for areas where high power consumption is a concern, such as data centers or server rooms. With its rugged design, the UTS6H features advanced surge suppression technology and can handle higher current loads without compromising safety. It also includes additional outlets and USB charging ports for added convenience, making it an indispensable tool for users with multiple electronic devices.

Moving on to the UTS10BI, this unit is designed for advanced users needing superior protection and versatility. It boasts ten outlets and features advanced filtering technologies to eliminate electrical noise, ensuring stable power delivery to sensitive equipment. The UTS10BI also includes smart technologies, such as energy monitoring, which helps users track power consumption and optimize energy usage. Additionally, it is equipped with safety features such as child-proof outlets and surge protection status indicators.

Lastly, the BU154A is a compact power management solution geared towards both commercial and residential users. It features a slim design that is easily mountable in various settings. With multiple outlets and the ability to accommodate larger plugs, the BU154A provides flexibility in connecting different devices. Its built-in surge protection safeguards connected electronics from voltage fluctuations, while its thermal protection feature prevents overheating. This unit is ideal for users seeking efficient power management without taking up too much space.

In summary, the APC UTS6, UTS6H, UTS10BI, and BU154A are innovative solutions designed to address specific user needs in power management and surge protection. Each model combines advanced technology, a range of features, and robust safety mechanisms to ensure reliable performance and protection of electronic devices in various environments.
Top Page Image Contents