GBC Laminator manual Hyholqj, Setup Procedure

Page 17

F-60 Operation and Maintenance Manual

/HYHOLQJ

Installation

 

 

☞ A NOTE ABOUT RECYCLING

 

 

The crate components can be reused for shipping the

Tools required:

 

machine again, or can be disassembled and the wood

 

 

 

 

and screws recycled. The shrink wrap is not recyclable,

•

Adjustable wrench

 

however, so it must be discarded.

•

Carpenter's level

 

14. Level the laminator using the procedure later in

 

 

 

 

6HWXSthis section.

To level the laminator:

 

 

1. Raise each end, remove the castors and install a

Once the F-60 Laminator has been unpacked and

 

leveling pad and stud onto each of the foot brackets

 

at the four bottom corners of the laminator. Thread

moved into final position check each of the following

 

third nut on stud above foot bracket.

 

items.

2.

Thread stud into 4 leveling pads lock down with

 

Tools required:

nut. Thread second nut onto stud.

•1/8" hex wrench

•Adjustable wrench

Setup Procedure:

1.Inspect the laminator for any obvious shipping damage.

2.Using a 1/8" hex wrench, remove the screws secur- ing the cabinet panel to the control (electrical) side of the machine.

3.Using a 1/8" hex wrench, remove the screws secur- ing the cabinet panel to the drive side of the machine and rotate the panel around the clutch knob.

4.Inspect all the bolts and tighten any that were loos- ened during shipping.

5.Set the nip. (See Maintenance for the procedure.)

6.Replace both cabinet covers.

3.Place a carpenter's level front to rear across the two lower tie bars at one end of the machine.

4.Level this end of the machine front to rear, raising or lowering the leveling pads by adjusting the mid- dle nuts on the foot bolts.

5.Move the level to the other end of the machine and level front to rear.

6.Place the level directly on one of the tie bars and level the machine side to side.

7.Recheck the front to rear level condition to insure that it has not changed. If it has, repeat the leveling procedure.

8.When all the measurements indicate that the machine is level, tighten down the top nuts on the foot brackets to lock the pads in their current posi- tion.

© GBC Pro-Tech 1998 July

2-5

Page 16 Page 18
Image 17
Page 16 Page 18
Contents Page Page 0DLQWHQDQFH0DQXDO Operation and Maintenance Manual 6HFWLRQ Procedure, Pass Push either Twist pressed Operation and Maintenance Manual SafetyDXWLRQin an emergencyDUQLQJ. /DEHO/RFDWLRQV Inside cabinet Decal Meaning Blank 6HFWLRQ ,QVWDOODWLRQ Laminator Space Requirements InstallationTo uncrate the laminator Tools requiredFork Lift Label Locations Hyholqj Setup ProcedureStartup Checklist Operation Upper Roll Heat ON/OFF Turns 2SHUDWRUOperation &RQWUROVFaces outward from the laminating roll. This 6HWXSPull roll clutch tension adjustment Operation Operation and Maintenance Manual3URFHVV&RQWURO&KDUWV +RW 3URFHGXUH 3DVV OperationF-60 Operation and Maintenance Manual Identification Diagram352&66&21752/&+$57 352&66&21752/,$*5$0352&66&21752/&+$57 Operation and Maintenance ManualOperation352&66&21752/,$*5$0 One Pass MountingOne Pass Mount and Laminate 352&66&21752/&+$57352&66&21752/,$*5$0 352&66&21752/,$*5$0 352&66&21752/&+$57Encapsulation Product 3 Mil Gloss/3Mil Gloss Process Encapsulation Date352&66&21752/,$*5$0 352&66&21752/&+$57Cold Overlamination Process Cold Overlamination Date352&66&21752/,$*5$0$ 352&66&21752/&+$57$Cold Mount and Laminate First Pass Product Process Cold Mount & Laminate First Pass Date352&66&21752/,$*5$0% 352&66&21752/&+$57%Cold Mount and Laminate Second Pass Product Process Cold Mount & Laminate Second Pass Date352&66&21752/,$*5$0$ 352&66&21752/&+$57$Mount and Hot Overlaminate First Pass Product Process Mount & Hot Overlaminate First Pass Date352&66&21752/,$*5$0% 352&66&21752/&+$57%Mount and Hot Overlaminate Second Pass Product7URXEOHVKRRWLQJ To clean the cabinet and covers Maintenance and TroubleshootingTo clean beads of adhesive, dust and dirt from the rolls $GMXVWLQJWKH1LS KDLQ7HQVLRQLQJ To adjust the chain tensionXeulfdwlrq 2XWSXW7URXEOHVKRRWLQJ*XLGH Customer’s sole and exclusive remedy under this This warranty specifically does not coverUnauthorized customer alterations will void this Warranty Warranty Quantity Part DescriptionSpecifications Index QGHUnpacking 2-3Crate Upper main roll Warranty

Laminator specifications

The GBC Laminator is a versatile and reliable tool designed for both home and office use, providing an efficient solution for preserving and enhancing documents through lamination. This innovative device offers a range of features, technologies, and characteristics that make it a popular choice among users who require high-quality lamination for various purposes.

One of the main features of the GBC Laminator is its user-friendly design, which allows for easy operation even for beginners. The intuitive control panel typically includes simple buttons for powering the device on or off, as well as temperature and speed settings. Many models also come with an indicator light that signals when the laminator is ready for use, ensuring optimal performance and preventing damage to documents.

The laminator employs advanced thermal laminating technology, which uses heat to seal plastic film around the document, creating a durable, protective layer. This process is highly effective for preserving important documents, such as certificates, photographs, and menus. Notably, the GBC Laminator is compatible with a variety of pouch sizes and thicknesses, accommodating different project needs. Common thicknesses range from 3 mil to 10 mil, allowing for flexibility in choosing the right level of protection.

Another standout characteristic of the GBC Laminator is its fast lamination speed. Many models can laminate a standard-size document in under a minute, significantly improving efficiency for users with large volumes of work. Additionally, some laminators feature a quick warm-up time, readying the machine for action in as little as five minutes.

The GBC Laminator also emphasizes safety, incorporating intelligent features such as a heat guard and auto shut-off function. This reduces the risk of burns and conserves energy, making it an ideal option for settings where safety is paramount.

Portability is another important aspect, with many GBC Laminators designed to be lightweight and compact. This makes it easy to transport between different locations or store in small spaces when not in use.

In conclusion, the GBC Laminator offers a perfect blend of functionality, safety, and user-friendliness, making it an indispensable tool for anyone needing reliable lamination. Whether for business presentations, creative projects, or personal documentation, the GBC Laminator is a top choice that ensures your materials are preserved and presented beautifully.
Top Page Image Contents