Oki ML5521, ML5520 manual Explanation of Menu Items

Page 34

EXPLANATION OF MENU ITEMS

These explanations are in alphabetical sequence to make it easier to look them up. Some items only appear when optional accessories are installed; others appear in several groups in the menu.

7 or 8 Bit Graphics, Default = 7

Change this setting to 8 if your system uses 8-bit graphics.

7 or 8 Bit Data Word, Default = 8

Change this setting to 7 if your system uses 7-bit data word lengths.

Auto CR, Default =No

IBM emulation only. If you want the printer to automatically add a carriage return when a Line Feed is received at the end of a line, change the setting to Yes.

Auto LF, Default = No

If your printout is consistently double spaced, select No; if it overprints, select Yes.

Auto Feed XT, Default = Invalid

Epson emulation only. In the Epson emulation, the XT signal on pin 14 of the parallel interface can control automatic line feed. Some interface cables are wired in such a way that automatic line feed is always in effect: this item eliminates this potential problem. If your system uses pin 14 of the parallel interface to control automatic line feed, change the setting to Valid.

Auto Select, Default = No

Determines whether or not your printer will automatically be selected after you load in paper. With the factory default engaged, the printer will be deselected so that you can set the Top of Form. If you always use the same Top of Form position, change the setting to Yes.

MENU MODE > 34

Image 34

Contents ML5520/21 Preface Contents Index Oki contact details Page Forms Tear-Off Features / TipsIntroduction Paper ParkTop of Form TOF Turning the Platen KnobControlling Access to the Printer Emulations Installing the DriverPrinter Drivers Printer DriversIBM Proprinter Using a Compatible DriverInterfaces General Epson FXConnecting the USB Cable Printer’s USB portPrinter Drivers Components Rear Feed Continuous Forms Using Your PrinterComponents TOP Feed Single Sheets TOP of Form TOF To print the Menu Forms TEAR-OFFTo use the Tear key Setting TOP of Form TOF Forms Tear-Off set to OFF defaultSEL light goes off and the red alarm light comes on Forms Tear-Off set to onForms TEAR-OFF Feature Temporarily Changing the TOP of FormPotential Issues with Software Packages Changing the Forms TEAR-OFF Setting Manual Forms TEAR-OFFContinuous Forms to Single Sheets Paper ParkChanging Paper Paths Never park labelsSingle Sheets to Continuous Forms Press FF/LOAD Setting Media Printhead GAPHigh Speed Draft HSD Utility UTL-the defaultPrint Quality Super Speed Draft SSDEpson and IBM Emulations Character PitchMicroline Emulation Emulations Printer ResetChanging Emulations Menu Mode Menu Mode KeysPrinting the Menu Settings Entering and Exiting Menu ModeResetting the Menu to the Factory Defaults Printing ALL Menu SettingsMenu Settings Group Settings13.6 17.1 cpi, 20 cpi Invalid, Valid Explanation of Menu Items Bottom Margin, Default = Valid Baud Rate, Default = 9600 bpsBi-direction, Default = Enable Busy Line, Default = SSDCode Page, Default = USA Character Set, Default = IBM SetCharacter Set, Default = Standard CSF Bin Select, Default = BinEmulation Mode, Default = IBM PPR DSR Signal, Default = ValidDTR Signal, Default = Ready On Power Up ESC SI Pitch, Default = 17 cpiOperator Panel Function, Default = Full Operation Language Set, Default = AsciiLine Spacing, Default = 6 lpi Length, Default = 11-2/3 or 1/2Power Saving, Default = Enable Paper Out Override, Default = NoPower Save Time, Default = 5 min Print Mode, Default = UtilityProportional Spacing, Default = No Print Registration, Default =Print Suppress Effective, Default = Yes Protocol, Default = Ready/BusySize, Default = Single SI Select Pitch 10 cpi, Default = 17.1 cpiSI Select Pitch 12 cpi, Default = 20 cpi Skip Over Perforation, Default = NoMaintenance Replacing the Ribbon CartridgeIf ribbon should contact the eyes Printhead may be HOTIf ribbon should contact the skin Rear Feed Loading PaperLoading Rear Feed Paper from the Back of the Printer Maintenance 5520 5521 If the paper is too loose, or too tight, it can cause jams Maintenance Loading Rear Feed Paper from the Front of the Printer 10 9.516 If the paper is too loose or too tight it can cause jams Reinstall the sheet feeder Maintenance TOP Feed Single Sheets Clearing Paper Jams Rear Feed JamsMaintenance Defective Paper Rear FEED, Repeating Paper JamsMisaligned Paper Maintenance Maintenance Single Sheet Paper Jams Cleaning the Housing Maintenance Solution TroubleshootingProblem General InformationSolutions Ink smears on the paper when I print narrow columns There are dots missing in my printouts Continuous-form paper sticks to the sheet guide Parts and Accessories Purchasing Parts & AccessoriesOption Part number ML5520 ML5521 IBM Proprinter III Commands Printer Control CodesESC % G Epson FX Commands DC3 OKI Microline Standard Commands ESC Y OFF Escz Specifications SpecificationUPC A, UPC E Paper Specifications Top onlyML5520 Location Setting UP Your PrinterUnpacking Setting UP Your Printer Setting UP Your Printer Installing the Ribbon Cartridge Ribbon Cartridge HandlingPage Power Connection Computer Connections USB, Specification 1.1 CompliantParallel LPT, Ieee Testing the Printer Loading PaperFont Sample Test Setting UP Your Printer Hexadecimal Dump Mode Index BufferLength Time Out Oki Data Corporation Oki Systems UK LimitedOki Systems Ireland Limited Oki Hong Kong LimitedML5520/21