Oki ML5520, ML5521 manual Baud Rate, Default = 9600 bps, Bi-direction, Default = Enable

Page 35

Baud Rate, Default = 9600 bps

Appears only if optional Serial Interface is installed. Set this to match your system’s transmission speed.

Bi-direction, Default = Enable

Change this setting if you wish to disable bi-directional transmission (PnP) in Nibble mode.

Bottom Margin, Default = Valid

Change to Invalid if you want the printer to ignore the bottom margin setting.

CAUTION!

Setting the Bottom Margin to Invalid can cause loss of data and damage the printhead by allowing printing without paper.

Busy Line, Default = SSD-

Appears only when the optional Serial Interface is installed. If Ready/ Busy protocol (factory default) is selected, you can choose which line your system monitors for a busy signal:

lSSD -9V, select SSD-

lSSD +9V, select SSD+

lDTR -9V, select DTR

lRTS -9V, select RTS Busy Time, Default = 200 ms

Appears only when the optional Serial Interface is installed. Sets the length of the busy signal when the Ready/Busy protocol (factory default) is engaged.

Centering Position, Default = DEFAULT

Used to limit printhead travel when printing narrow columns.

lSelect Mode 1 for the narrow carriage printer.

lSelect Mode 1 or Mode 2 for the wide carriage printer.

MENU MODE > 35

Image 35

Contents ML5520/21 Preface Contents Index Oki contact details Page Paper Park Features / TipsIntroduction Forms Tear-OffTurning the Platen Knob Top of Form TOFControlling Access to the Printer Printer Drivers Installing the DriverPrinter Drivers EmulationsEpson FX Using a Compatible DriverInterfaces General IBM ProprinterPrinter’s USB port Connecting the USB CablePrinter Drivers Components TOP Feed Single Sheets Using Your PrinterComponents Rear Feed Continuous Forms TOP of Form TOF To use the Tear key Forms TEAR-OFFTo print the Menu Forms Tear-Off set to OFF default Setting TOP of Form TOFForms Tear-Off set to on SEL light goes off and the red alarm light comes onTemporarily Changing the TOP of Form Forms TEAR-OFF FeaturePotential Issues with Software Packages Manual Forms TEAR-OFF Changing the Forms TEAR-OFF SettingNever park labels Paper ParkChanging Paper Paths Continuous Forms to Single SheetsSingle Sheets to Continuous Forms Press FF/LOAD Printhead GAP Setting MediaSuper Speed Draft SSD Utility UTL-the defaultPrint Quality High Speed Draft HSDMicroline Emulation Character PitchEpson and IBM Emulations Changing Emulations Printer ResetEmulations Menu Mode Keys Menu ModePrinting ALL Menu Settings Entering and Exiting Menu ModeResetting the Menu to the Factory Defaults Printing the Menu SettingsGroup Settings Menu Settings13.6 17.1 cpi, 20 cpi Invalid, Valid Explanation of Menu Items Busy Line, Default = SSD Baud Rate, Default = 9600 bpsBi-direction, Default = Enable Bottom Margin, Default = ValidCSF Bin Select, Default = Bin Character Set, Default = IBM SetCharacter Set, Default = Standard Code Page, Default = USAESC SI Pitch, Default = 17 cpi DSR Signal, Default = ValidDTR Signal, Default = Ready On Power Up Emulation Mode, Default = IBM PPRLength, Default = 11-2/3 or 1/2 Language Set, Default = AsciiLine Spacing, Default = 6 lpi Operator Panel Function, Default = Full OperationPrint Mode, Default = Utility Paper Out Override, Default = NoPower Save Time, Default = 5 min Power Saving, Default = EnableProtocol, Default = Ready/Busy Print Registration, Default =Print Suppress Effective, Default = Yes Proportional Spacing, Default = NoSkip Over Perforation, Default = No SI Select Pitch 10 cpi, Default = 17.1 cpiSI Select Pitch 12 cpi, Default = 20 cpi Size, Default = SingleReplacing the Ribbon Cartridge MaintenanceIf ribbon should contact the skin Printhead may be HOTIf ribbon should contact the eyes Loading Rear Feed Paper from the Back of the Printer Loading PaperRear Feed Maintenance 5520 5521 If the paper is too loose, or too tight, it can cause jams Maintenance Loading Rear Feed Paper from the Front of the Printer 10 9.516 If the paper is too loose or too tight it can cause jams Reinstall the sheet feeder Maintenance TOP Feed Single Sheets Rear Feed Jams Clearing Paper JamsMaintenance Misaligned Paper Rear FEED, Repeating Paper JamsDefective Paper Maintenance Maintenance Single Sheet Paper Jams Cleaning the Housing Maintenance General Information TroubleshootingProblem SolutionSolutions Ink smears on the paper when I print narrow columns There are dots missing in my printouts Continuous-form paper sticks to the sheet guide Purchasing Parts & Accessories Parts and AccessoriesOption Part number ML5520 ML5521 Printer Control Codes IBM Proprinter III CommandsESC % G Epson FX Commands DC3 OKI Microline Standard Commands ESC Y OFF Escz Specification SpecificationsUPC A, UPC E Top only Paper SpecificationsML5520 Unpacking Setting UP Your PrinterLocation Setting UP Your Printer Setting UP Your Printer Ribbon Cartridge Handling Installing the Ribbon CartridgePage Power Connection Parallel LPT, Ieee USB, Specification 1.1 CompliantComputer Connections Loading Paper Testing the PrinterFont Sample Test Setting UP Your Printer Hexadecimal Dump Mode Buffer IndexLength Time Out Oki Hong Kong Limited Oki Systems UK LimitedOki Systems Ireland Limited Oki Data CorporationML5520/21