MK Sound V-1250THX operation manual Wiring with the M&K HP-80 or VF-80 HIGH-PASS Filters NON-THX

V-1250THX subwoofer page 11

FIGURE 6 - WIRING TWO SUBWOOFERS TO AN AMP

OR PREAMP WITH ONE SET OF PREAMP OUTPUTS

POWER AMP

MAIN IN

LEFT RIGHT

MAIN OUT

PREAMP LEFT RIGHT

use one Y-connector

for each channel to split the output of the preamp

BASS LEVEL				LOW PASS
REFERENCE	LEFT/MONO	RIGHT	+	FILTER
+3 dB	VARIABLE			80 Hz
+6 dB				24 dB/OCTAVE
	THX	INPUT	–
				THX
			PHASE

CAUTION

RISK OF ELECTRIC SHOCK

DO NOT OPEN

AVIS: RISQUE DE CHOC

ELECTRIQUE. NE PAS OUVRIR.

Manufactured under license

from Lucasfilm Ltd. Lucasfilm and THX are registered trademarks of Lucasfilm Ltd.

CAUTION:

DISCONNECT SUPPLY CORD

BEFORE CHANGING FUSE.

REPLACE FUSE ONLY

WITH SAME TYPE.

ATTENTION:

DEBRANCHER AVANT DE

REMPLACER LE FUSIBLE.

UTILIZER UN FUSIBLE

DE RECHANGE

DE MEME TYPE.

Made in U.S.A.
		VAC O R PTO4 AMPR A T I O N
M I L L E R & K R E I S E L S O U N D	120
		50/60 Hz
1 0 3 9 1 J e f f e r s o n B lv d , C u lv e r C it y , C A 9SLOW0 2-BLOW3 2 3 1 0 / 2 0 4 - 2 8 5 4

BASS LEVEL				LOW PASS
REFERENCE	LEFT/MONO	RIGHT	+	FILTER
+3 dB	VARIABLE			80 Hz
+6 dB				24 dB/OCTAVE
	THX	INPUT	–
				THX
			PHASE

CAUTION

RISK OF ELECTRIC SHOCK

DO NOT OPEN

AVIS: RISQUE DE CHOC

ELECTRIQUE. NE PAS OUVRIR.

Manufactured under license

from Lucasfilm Ltd. Lucasfilm and THX are registered trademarks of Lucasfilm Ltd.

CAUTION:

DISCONNECT SUPPLY CORD

BEFORE CHANGING FUSE.

REPLACE FUSE ONLY

WITH SAME TYPE.

ATTENTION:

DEBRANCHER AVANT DE

REMPLACER LE FUSIBLE.

UTILIZER UN FUSIBLE

DE RECHANGE

DE MEME TYPE.

Made in U.S.A.
		VAC O R PTO4 AMPR A T I O N
M I L L E R & K R E I S E L S O U N D	120
		50/60 Hz
1 0 3 9 1 J e f f e r s o n B lv d , C u lv e r C it y , C A 9SLOW0 2-BLOW3 2 3 1 0 / 2 0 4 - 2 8 5 4

If you have two subwoofers, it is not necessary to use both inputs on each subwoofer. Connect the interconnect cable to one "FROM PREAMP" jack only. Run the Left channel interconnect cable to the Left subwoofer and the Right interconnect cable to the Right subwoofer. See Figures 4 and 6.

WIRING WITH THE M&K HP-80 OR VF-80 HIGH-PASS FILTERS (NON-THX)

The M&K HP-80 and VF-80 High-Pass Filters can improve any system that allows its preamp and power amp stages to be separated, by filtering the bass fed to the main amp and Satellite speakers.

These filters will give your system greater dynamic range, lower distortion, and an increased maximum output. To use these filters with an integrated amp or receiver, the amp or receiver MUST have back panel RCA jacks labelled PREAMP/MAIN OUTPUT and POWER AMP/MAIN INPUT. There may be a switch or jumper connections between them, which you will have to remove. If you have any questions about your components, contact your dealer or M&K.

For non-THX systems, your subwoofer is optimized for use with the HP-80 High-Pass Filter. We strongly recommend that you use this filter with any component system that allows for its use. When you use this subwoofer with an HP-80 and M&K Satellites, the combination forms a 4th order Linkwitz-Riley crossover between satellite and subwoofer. The linear phase of this crossover means uncompromised performance with great flexibility in system setup, without requiring elaborate calibrations or adjustments.

Do not use either of these filters with a THX controller. The THX controller has the appropriate filters in its built-in crossover circuitry. Also, do not use a SUBWOOFER OUTPUT jack on your amp or processor to feed any of these filters.

To connect one of these filters, run one set of shielded RCA - RCA interconnect cables from the