Toshiba GA-1190 Monitor Volume, Alarm Volume, Reception Mode, Resolution, Receive Interval, 12TTI

Page 104

10TopAccess ADMINISTRATION TAB PAGE - SETUP MENU (Printing Function)

4)Monitor Volume

Select the volume of the line monitor during transmission.

5)Alarm Volume

Selects the volume of the alarm.

6)Reception Mode

Select how this equipment activates when a fax is received.

-Auto — Select this to automatically receive incoming originals when the bell rings. Select this when the line is being used exclusively by the fax transmission.

-Manual — Select this to manually receive incoming originals after pressing the Start but- ton on the Control Panel.

7)Resolution

Select the default resolution for sending faxes.

-Standard — Select this to set the Standard mode as the default resolution appropriate for the originals in which the text is regular size.

-Fine — Select this to set the Fine mode as the default resolution appropriate for the orig- inals in which the text is small or a detailed drawing is contained.

-Ultra Fine — Select this to set the Ultra-Fine mode as the default resolution appropriate for the originals in which the text is particularly small or a precision drawing is contained.

8)Receive Interval

Selects the interval of transmissions. Transmissions are forcibly paused every 4 times to receive incoming faxes during each interval. This interval can be set from 0 to 15 minutes.

9)Redial Mode

Selects redialing intervals and the number of times to redial when the line is busy.

-Interval — Selects the redialing interval from 0 to 15 minutes.

-Counter — Selects the number of times to redial from 0 to 14.

10)Memory TX

Selects whether the fax data are temporarily stored in the memory before transmission or not.

11)Security TX

Checks whether the number you dialed matches that of a destination or not and determines whether the fax data should be transmitted or not. If these numbers do not match, the fax data will not be transmitted to prevent inadvertent data transmission caused by dialing mis- takes or misconnection of a telephone switchboard. You can select whether to enable or dis- able this function.

12)TTI

Select whether printing a transmission header (TTI) to identify the sender of received faxes.

13)RTI

Select whether printing a reception header (RTI) on received faxes to clearly identify the time, date, and page count of received faxes.

14)ECM

Select whether enabling or disabling the ECM (Error Correction Mode) to automatically re- send any portion of the document affected by phone line noise or distortion.

15)Discard

Select whether discarding the lower portion of the received fax image if it is larger than the recording paper.

16)Reduction

Select whether reducing the received fax image if it is larger than the effective printing area of the recording paper.

17)Recovery Transmit

Select whether re-transmitting a fax after failing the initially specified number of redial attempts. When this is enabled, select the stored time length from 1 to 24 hours.

102 Setting up Fax Settings

Page 103 Page 105
Image 104
Page 103 Page 105
Contents Setup Guide for Printing Functions Page Preface Software License Agreement Grant of LicenseDisclaimer of Warranty Before Reading This Manual Lineup of our manualsBasic functions Facsimile functionsTopAccess Scanning functionsHow to read this manual Symbols in this manual TrademarksContents TopAccess Device TAB Setting up Copier Settings Setting up Fax SettingsSetting up Printer Settings Setting up Print Service Settings Printing FunctionAppendix Overview OverviewContents OverviewMenu Web browser Use environments of TopAccessNetwork Basic Operations on Screens Equipment Various Screens Basic Operations on Each ScreenVarious Screens Ready screen Copy mode main screenMode main screens Digit entry screen Error message screenMenu selection screen To select mode main screen To return to main screen for each modeBasic Operations on Each Screen User Functions button and screen transitionTo select each menu Button FunctionCancel JOB Example of menu selectionTo key in digits Button /Digital key FunctionPage To Cancel Print Jobs To Print PCL/PS Font List PCL font list / PS font listTo Cancel Print Jobs Press or to select YES, and then press the Enter buttonTo Print PCL/PS Font List PCL font list / PS font listPage Printing Lists Equipment To Print ListsConfiguration To Print ListsPress the User Functions button Press or to select LISTS, and then press the Enter buttonNIC status Page Configuring Networks Equipment Network Configuration from Equipment To use TopAccessEthernet Configuration Ethernet ConfigurationPress the Cancel button Press the Enter buttonOnce to return the screen to Network menu screenConfiguring TCP/IP using only Dhcp TCP/IP ConfigurationConfiguring TCP/IP using Dhcp or Auto IP function 03.TCP/IP Tial SETUP, and then press User functions mode main screen AppearsPress To select INI Enter buttonDefault Gateway XXX.XXX.XXX.XXX Complete IPX/SPX Configuration Press or to select ENABLE, and then press the Enter buttonPress or to select the desired frame type Frame Type 1.AUTO Sence 2.IEEE802.2 3.IEEE802.3AppleTalk Configuration Apple Talk 1.ENABLE 2.DISABLEApple Talk Http Configuration Press or to select HTTP, and then press the Enter buttonHttp Page TopAccess Overview Accessing TopAccess from Your ComputerTopAccess Overview End user modeAdministrator mode TopAccess top page for end users is displayed Accessing TopAccess from Your ComputerAccessing TopAccess Click each tab to display each main Click the menu name to display the desired TopAccess screen structure Menu barSubmenu bar Top linkAccessing TopAccess from Your Computer TopAccess Device TAB TopAccess Device TabTopAccess Device Tab Refresh iconDevice Information PaperError display Device status indicatorsOptions AlertsPage Managing Address Book Managing MailboxesAdding or editing a contact Managing Address BookManaging contacts in the address book Click Fax Setting Enter following items to specify the recipient informationManaging Address Book Click the link that you want to delete in the contacts list Contact Properties page, click Save to add new contactDeleting a contact Adding or editing a group Managing groups in the address bookClick Delete Enter following items to specify the group properties Check the Fax boxes of users to add the Fax recipientsClick OK Deleting a groupManaging Mailboxes Confidential MailboxBulletin Board mailbox Forward MailboxSetting up an Open Mailbox Enter the password for the mailbox and click OK Click EditSelect agents and click Select Agent Box Number MailBox settingPassword Destination setting Mailbox Selecting the recipients from the address bookSelecting the groups from the address book Relay end terminal report Click Relay End Terminal ReportWant to send the transmission result list Relay End Terminal Report page is displayedEnter the password for the mailbox and click OK Deleting an Open MailboxSelected mailbox is deleted Page TopAccess Counter TAB Viewing CountersViewing Counters Displaying the total counterYou can check the total counter in this Print CounterDisplaying the department counter Click the Counters tab and the Department menuDepartment Code field and click Enter Department menu page is displayedPage Setting up Printer Settings 105 111Displaying Version Information 115 General submenu page, set the device settings as required Setting up Device SettingsClick the Setup menu and General submenu Setting up the device information Click OK to apply the changesSetting up the Web general setting Setting up the energy saveSetting up the time and date Setting up Network Settings Printing Function Click the Setup menu and Network submenuClick Save Setting up the TCP/IP Setting up the IPX/SPX Setting up the AppleTalkSetting up the Bonjour Enable BonjourService Name Link-Local Host NameSetting up the DNS session Enable DNSPrimary DNS Server Address Secondary DNS Server AddressHost Name Setting up the Ddns sessionEnable Ddns Setting up the NetWare session Setting up the Http network service Enable Http ServerPrimary Port Number Secondary Port NumberSetting up the Snmp network service Enable SnmpEnable Authentication Trap Read CommunityEnable Alerts Trap IP Trap AddressIP Trap Community IPX Trap AddressCopier submenu page, set the copier settings as required Setting up Copier SettingsClick the Setup menu and Copier submenu Setting up the copier settings Original ModeSorter Mode Priority ExposureFax submenu page, set the fax settings as required Setting up Fax SettingsClick the Setup menu and Fax submenu Click Save Setting up the Fax settings Ringer VolumeTerminal ID Fax NumberMonitor Volume Alarm VolumeReception Mode Resolution19When Memory Full 18Send after Scan20Account Code 21Separator28Polling Report 29Relay Originator30Relay Station Report 31Relay End ReportPrinter submenu page, set the Printer settings as required Setting up Printer SettingsClick the Setup menu and Printer submenu Setting up the general setting Wide A4 Mode for PCLLT--A4/LD--A3 Print StartupSetting up the default Raw job setting Setting up the Raw job setting Paper SourceEnter following items as required Selected queue is deleted Required Setting up Print Service Settings Printing FunctionClick the Setup menu and Print Service submenu Setting up the Raw TCP print Enable Raw TCPEnable Raw bi-directional Port NumberSetting up the LPD print Setting up the IPP printSetting up the NetWare print Click the Setup menu and Version submenu Displaying Version InformationPage TopAccess Administration TAB page Maintenance Menu Restoring data from the backup files About the Maintenance FunctionsInstall Language Switching Languages Click the Maintenance menu and Install Language submenuInsert the Client Utilities CD-ROM into a client PC Select the desired language in the Select drop down boxClick Upload Backing up Data Click the Maintenance menu and Backup submenuClick Create New File for the data that you want to backup Click Refresh on the right side Right-click the File Name link and select Save Target AsClick Save Click Browse in the data section that you want to restore Restoring Data from Backup FileClick the Maintenance menu and Restore submenu Select a backup file and click Open Check the box of Address Book and click Restore Importing Address Book Data NameClick the Maintenance menu and Import submenu Click Browse... in the Address Book areaClick Import Click Create New File in the Address Book area Click the Maintenance menu and the Export submenuExporting Address Book Data Save As dialog box is displayed Click Browse... in the Department Code area Access the TopAccess in the administrator modeImporting Department Code Data Click the Refresh on the right side Exporting Department Code Data Click Create New File in the Department Code Export areaSave As dialog box is displayed Page Managing Department Codes on TopAccess for Administrators Managing Department Codes For Administrators 138Managing Department Codes For Administrators Troubleshooting TopAccess Error Messages 140TopAccess Error Messages Device status indicator listError message list TopAccess Message Corrective ActionPage Appendix List Print Format 144Configuration Page Example List Print FormatNIC Status Page Example XxxxxxxxxxxxPS Font List Example PCL Font List Example Page Index 144 105 Index GA-1190 OME060181B0 GA-1190
Related manuals
Manual 62 pages 62.09 Kb
Top Page Image Contents