Toshiba TDP-MT400 manual Preparing and using the remote control, Placement

Page 10

Preparing and using the remote control

English Français Español Deutsch Italiano Português Svenska

Placement

Loading dry-cell batteries

into the remote control

qRemove the battery cover.

Operating the remote control

Point the remote control toward the projector’s infrared remote sensor, and press a button on the remote control.

• Operating the projector from the front

Placement Styles

As shown in the figures below, this device can be placed in 4 different styles.

The factory setting is “floor-mounted front projection.” Set the Projection mode in the default setting menu p.31 , in accordance with your needs.

Floor-mounted front projection

 

Floor-mounted rear projection

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

wInsert the dry-cell batteries.

Be sure to align the plus and minus ends of the batteries properly.

Two batteries (R6, SIZE AA) are used.

eReplace the battery cover.

Approx. 15°

Approx.5m

• Operating the projector from the rear

Approx. 15°

Approx.5m

Ceiling-mounted front projection

 

Ceiling-mounted rear projection

 

Preparations

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

WARNING

Always obey the instructions listed in IMPORTANT SAFETY INSTRUCTIONS when placing the unit. Attempting to clean/replace the lamp at a high site by yourself may cause you to drop down, thus resulting in injury.

If you wish to mount the projector on the ceiling, be sure to ask your dealer to do so. Mounting the projector on a ceiling requires special ceiling brackets (sold separately) and specialized knowledge. Improper mounting could cause the projector to fall, resulting in an accident.

If the projector is ceiling-mounted, install the breaker for turning off the power in case of anomaly. Let everyone involved with the use of the projector know that fact.

Projection Distance and Size

Dry-cell batteries

Before using the batteries, be sure to observe the Safety Precautions described in previous pages.

Remove batteries from remote control when not using for extended periods.

If the remote control stops working, or if its range decreases, replace all the batteries with new ones.

Use the figures, tables, and formulas below to determine the projection size and projection distance. (Projection sizes are approximate values for full-size picture with no keystone adjustment.)

Screen As seen from above

a (min length) = projection size (inches) 0.0350

90°

a (max length) = projection size (inches) 0.0421

The remote control

The remote control may fail to operate if the infrared remote sensor is exposed to bright sunlight or fluorescent lighting.

Do not drop or bang.

Do not leave in hot or humid locations.

Do not get wet or place on top of wet objects.

Do not take apart.

In rare cases, ambient conditions could impede the operation of the remote control. If this happens, point the remote control at the main unit again, and repeat the operation.

As seen from the side

Lens center

H

90°

a

a is the distance (m) between the lens and the screen, and corresponds to a range of 1.50 m to

10.00m. H is the height from the image bottom to the center of the lens.

projection

projection distance a (m)

height (H)

size

min length

max length

(cm)

 

(zooming max)

(zooming min)

 

35.66

1.50

16.43

40

1.40

1.68

18.43

60

2.10

2.52

27.64

80

2.80

3.37

36.86

100

3.50

4.21

46.07

150

5.25

6.31

69.11

200

7.00

8.41

92.15

285.89

10.00

131.72

18

19

Image 10
Contents Others Maintenance Operations Preparations Before Using TDP-MT400Before Safety PrecautionsUsing USA onlyImportant Safety Instructions Before UsingImportant Safety Instructions Place and Manner of Installation Power Supply Cord SelectionImportant Precautions Save Original Packing MaterialsExemption Clauses Remote Control BatteriesOther Cautions and Informations Contents Checking the package contents Names of each part on the main unitParts on the rear panel SourcePreparing and using the remote control PlacementConnection Turning the power on and offOperations Turning the power on and off Basic operationsUsing handy features Basic operationsCutting off the picture temporarily Mute Using handy featuresFreezing the image Freeze How to use the menus Using the menusImage adjustment menu Default setting menu Using the menuDisplay setting menu Screen sizeAbout lamp Lamp replacementMaintenance Displaying Information Status displayLens and main unit cleaning Lamp replacementTrouble indications Before calling service personnelOthers List of supported signals RGB signals SpecificationsList of general specifications SpecificationList of supported signals Y/PB/PR signals SpecificationsList of supported signals DVI signals List of supported signals Video, S-Video signalsControl terminal Main CommandsPin arrangement for the DVI-D terminal Pin assignment