Toshiba TDP-MT400 manual Parts on the rear panel, Source

Page 9

Names of each part on the control panel and remote control

Control panel

Remote Control

English Français Español Deutsch Italiano Português Svenska

Parts on the rear panel

(1)

(2)

(3)

(4)

(5)

(6)

(7)

(9)(10) (11)

(8)

(1)

 

(7)

(2)

(6)

(3)

 

(4)

 

(5)

 

Remote control

 

transmitter

(3)

(4)

 

(6)

(2)

(13)

(12)

(1)

(8)

(7)

 

(10)

(9)

(8)

Preparations

 

Name

: Main Function

 

(1)

Infrared remote sensor

: Senses commands from the remote control. p.18

(2)

CONTROL terminal

: When operating the projector via a computer, connect

 

 

this to the controlling computer’s RS-232C port. p.43

 

 

 

(3)

S-VIDEO terminal

: Input S video signals from video equipment.

 

(4)

VIDEO terminal

: Input video signals from video equipment.

 

(5)

Component video terminal

: Input component video signal (Y/PB/PR) from a video

 

 

 

equipment or other source.

 

 

(6)

COMPUTER terminal

: Input RGB signal from a computer or other source.

 

 

Name

: Main Function

(1)

ENTER button

: Accepts the selected mode.

(2)

MENU button

: Displays menus. p.28

(3)

SET UP button

: Sets up image and mode. p.25

(4)

ON/STANDBY button

: Turns the power on/off (standby). p.21

(5)

ON indicator

: Displays whether power is on or off. p.21

(6)

INPUT button

: Selects input. p.23

(7)

RETURN button

: Goes back one screen.

(8)

Selection button

: Menu selections and adjustments,etc. p.29

(9)

LAMP indicator

: Displays lamp mode. p.22

(10) TEMP indicator

: Lights when internal temperature is too high. p.36

(11) FAN indicator

: Displays cooling fan mode. p.36

(12) FREEZE button

: Pauses image. p.27

(13) MUTE button

: Cuts off the picture temporarily. p.27

Note

For the remainder of this manual, buttons are referred to as follows:

Selection buttons ; ENTER button

(7)

DVI-D terminal

: Input digital RGB signal from a computer or other

 

 

source.

(8)

Main power switch

: AC power line ON (standby)/OFF.

(9)

AC IN socket

: Connect the supplied power cord here.

(10)

Antitheft lock hole

: Attach a safety cable or any other antitheft device.

Notes

Although this owner’s manual abbreviates component video signals as Y/PB/PR, the product also supports signals from video equipment marked “Y/CB/CR.”

Input signal specifications for the DVI terminal complies with the DVI 1.0 Specifications.

Please note that the operations for the functions not covered in these specifications are not guaranteed. Because this is an evolving technology, it is possible that some devices may not operate properly with the projector.

This supports HDCP (High-bandwidth Digital Content Protection).

16

17

Image 9
Contents TDP-MT400 Others Maintenance Operations Preparations Before UsingUsing Safety PrecautionsBefore USA onlyBefore Using Important Safety InstructionsImportant Safety Instructions Important Precautions Power Supply Cord SelectionPlace and Manner of Installation Save Original Packing MaterialsRemote Control Batteries Exemption ClausesOther Cautions and Informations Contents Names of each part on the main unit Checking the package contentsSource Parts on the rear panelPlacement Preparing and using the remote controlTurning the power on and off ConnectionOperations Basic operations Turning the power on and offBasic operations Using handy featuresUsing handy features Cutting off the picture temporarily MuteFreezing the image Freeze Using the menus How to use the menusImage adjustment menu Display setting menu Using the menuDefault setting menu Screen sizeMaintenance Lamp replacementAbout lamp Displaying Information Status displayLamp replacement Lens and main unit cleaningBefore calling service personnel Trouble indicationsOthers List of general specifications SpecificationsList of supported signals RGB signals SpecificationList of supported signals DVI signals SpecificationsList of supported signals Y/PB/PR signals List of supported signals Video, S-Video signalsPin arrangement for the DVI-D terminal Main CommandsControl terminal Pin assignment