Toshiba TDP-S21, TDP-S20 owner manual Specifications, List of supported signals Y/PB/PR signals

Specifications (Continued)

■List of supported signals (Y/PB/PR signals)

Signal format	fh(kHz)	fv(Hz)
480i(525i)@60Hz	15.73	59.94
480p(525p)@60Hz	31.47	59.94
576i(625i)@50Hz	15.63	50.00
576p(625p)@50Hz	31.25	50.00
720p(750p)@60Hz	45.00	60.00
720p(750p)@50Hz	37.50	50.00
1080i(1125i)@60Hz	33.75	60.00
1080i(1125i)@50Hz	28.13	50.00
1035i(1125i)@60Hz	33.75	60.00
1152i(1250i)@50Hz	31.25	50.00

■List of supported signals (Video, S-Video signals)

Video mode	fh(kHz)	fv(Hz)	fsc(MHz)
NTSC	15.73	60	3.58
PAL	15.63	50	4.43
SECAM	15.63	50	4.25 or 4.41
PAL-M	15.73	60	3.58
PAL-N	15.63	50	3.58
PAL-60	15.73	60	4.43
NTSC4.43	15.73	60	4.43

■Pin assignment of COMPUTER-1/2 & MONITOR terminals

■CONTROL terminal

●Pin assignment

			Pin No.	Signal Name	Description
	7		1	RXD	Receiving data
8	6		2	CTS	Consent to send
			3	DSR	Data set ready
5		3	4	GND	Signal ground
			5	RTS	Request to send
	4		6	N.C	No connection
2	1		7	TXD	Sending data
			8	GND	Signal ground

Mini DIN 8 pin connector

●Interface format

1	Communication method		RS-232C, 9600bps, No Parity, Data Length: 8 bits;
			Stop Bit Length:			1 bit
2	Communication format		STX (02h)		Command (3Byte)			ETX (03h)
			Only 1 command valid per communication.
3	Data format		For input commands, only ASCII-compliant all-uppercase
			alphanumeric characters supported.
4	Replies	Acknowledge		ACK (06h)		CR (0Dh)	Data		... Normally ended
				ACK (06h)		ESC (1Bh)			... Aborted
		No acknowledge		NAK (15h)

If commands are to be sent consecutively, wait for the response from the projector before sending the next command.

5 1

Pin Pin description

●Main Commands

106

15 11

Mini D sub 15 Pin connector

No.	During RGB input	During Y/PB/PR input
1	Video signal (R)	Color difference signal (PR)
2	Video signal (G)	Luminance signal (Y)
3	Video signal (B)	Color difference signal (PB)
4	GND	∗
5	GND	∗
6	GND (R)	GND (PR)
7	GND (G)	GND (Y)

Item	Command
Power on	PON
Power off	POF
Icon display on	MO0
Icon display off	MO1
Auto setting (RGB input)	PAT
Status display on	DON
Status display off	DOF

Item	Command
Computer (1) input select	IN1
Computer (2) input select	IN2
Video input select	IN3
S-video input select	IN4
Camera input select (TDP-S21)	IN5

Input Signal
• RGB input
RGB signals:	0.7V (p-p) 75 Ω
Horizontal sync signal:	TTL level (Pos/neg polarity)
Vertical sync signal:	TTL level (Pos/neg polarity)
• Y/PB/PR input
Y signal:	1.0V (p-p) 75 Ω
PB/PR signals:	0.7V (p-p) 75 Ω

8	GND (B)	GND (PB)
9	N.C	∗
10	GND	∗
11	GND	∗
12	N.C	∗
13	Horizontal sync signal	∗
14	Vertical sync signal	∗
15	N.C	∗

Note

• Contact your dealer for control cable and other commands.

■Separately Sold Product

Replacement Lamp Model TLPLV4

Others

∗Do not connect anything.

46 47