Toshiba TDP-TW420 owner manual Using the menus, How to set password from Off to On

Page 18

Using handy features (Continued)

How to set password (from [Off] to [On])

1Select [Password] in the Default setting 2 menu and press theor button.

2Select [Password setting] next, and press theorbutton.

3Select [On].

4Select [OK] and press thebutton.

The password entry screen is displayed.

Using the menus 1

You can call up on-screen menus, and conduct a number of adjustments and settings using the MENU button p.16 on the control panel (main unit side) and remote control.

N Setup using the Setting display

The menu shown below is for operation instructions purposes and might differ from the actual display.

1.Press the MENU button Display the Setting display menu.

2.Select a Category

5Enter the password using numeric keys of the remote control.

6The password setting will be set as [On].

How to operate when password is [On]

1Turn on the power.

2The lamp lights and the password entry screen appears.

3 Enter the password using numeric keys of the remote control.

If the entered password is correct, the start-up screen appears and the projector

goes into normal operation. If the password is wrong, a message appears to prompt

you to re-enter the password, and again the password entry screen is displayed. If

Select a category by using . There are following 6 categories:

Image adjustment menu p.36

Position adjustment menu p.37

Display setting menu

p.38

Default setting 1 menu

p.41

Default setting 2 menu

p.42

Status display menu

p.43

Displays the current adjustments and settings of selected category.

Item shown with gray cannot be adjusted with the current input source.

Operations

you enter a wrong password for more than 5 times, the projector will automatically

power off and enter standby mode.

3.Adjustments & Settings Press or to open the menu.

Note

•When the password setting is [On], the password function will be enabled only when the projector is restarted after the main power switch has been turned off. The password that you set will not be enabled when restarting from standby mode without turning off the main power switch.

How to set password (from [On] to [Off])

1Select [Password] in the Default setting 2 menu and press theor button.

The password entry screen is displayed.

2Enter the password using numeric keys of the remote control.

Item

Adjustment/Setting Value

These marks signify the items can be adjusted/set by using

.

These marks signify the items can be selected from the list by using .

These marks signify that there are options.

Press or

to display a list of options.

These marks signify that there are setting

screens. Press or to display a list of

setting screens.

*When no item is

changed, press .

4Select [OFF].

After an item is selected, apply it by

pressing .

Toggle items with

.

 

Select items with

and press

.

Fix selection with

.

 

•The figure shows displays given for operation instructions purposes. As the display may differ depending on the item, refer to the following applicable pages for the menu item you desire.

•To return to previous item, press the RETURN button.

•When Network or USB memory input is selected, pressing the MENU button twice displays the Setting display (2) menu.

4. End Press the MENU button once more.

(The menu will disappear automatically after 30 seconds, if no operation is conducted.)

34

35

Page 17 Page 19
Image 18
Page 17 Page 19
Contents TDP-TW420 USA only Trade Name Data Projector Model Name TDP-TW420For Home or Office USE Cleaning Power Cord ProtectionPower Sources HeatImportant Safety Instructions Place and Manner of Installation Moisture CondensationDisposal Important Precautions Avoid Volatile LiquidCopyrights Other InformationContents Checking the package contents Names of each part on the main unitLabel location Names of each part on the control panel and remote controlRemote Control Control panelLoading dry-cell batteries into the remote control Operating the remote ControlOperating a computer using the remote control PlacementConnection Connecting with computersConnecting with AV equipments Before connectionNTurning the power on Turning the power on and offNConnecting the power cord NTurning the power offAdjusting the screen size and focus Turn on the powerProjector placement angle adjustments Basic operationsBasic operations Using handy featuresUsing auto setting For computer input only Correcting the keystone distortionUsing handy features Zooming out the imagesResizing image Cutting off the picture and sound temporarily Mute Changing picture modeSetting the password How to change password Changing screen sizeSetup using the Setting display Using the menusHow to set password from Off to On How to operate when password is OnUsing the menus Image adjustment menuPosition adjustment menu Display setting menu Default setting menu Default setting 1 menuDefault setting 2 menu Displaying Information Status displayCommunication mode Before connecting via networkConnection using the Network Projector Windows Vista FunctionsHow to use the USB terminal Setting up the Network Projector/Network Utility Projector settings Be sure to read this subsectionCharacter entry Details on individual itemsWhen you have set Encryption to TKIP/AES Security for wireless LAN settings Network authenticationNetwork key When you have set Encryption to WEP Setting initializationDetailed description Computer settingsControl setting menu Projector nameSetting slideshow options Details on individual items Still ImageMovie Image Using the Network Projector Checking the projector statusHow to install Installing the applicationsHow to uninstall System RequirementsUsing the Network Utility Click on the Browse button, and select the file to send Using the Network UtilityClick on the Jpeg File icon Click on the iconClick on the Browse button and select the file to send Select the projector to transmit toPlay the video file via the Control window Transmission Mode Image Click on the Multiscreen iconArrange the virtual display layout Multiscreen Usage Examples ExampleLaunch the Network Utility software application Setting on the computerEasy Connect utility Click the Tool buttonUnplug the USB memory from the computer How to set up with USB memory connectionCopying the computer settings to the projector Unplug the USB memoryAdvanced setting To quit, click on the button on the Remote Control windowHow to use Profile settings Switching settings automatically at start-upProjecting images stored in a USB memory How to use the Jpeg Conversion Tool Projecting images stored in a USB memoryHow to use the Jpeg Conversion Tool Converting files created with Microsoft PowerPointMaking a presentation with converted Jpeg files How to use the Projector Configuration Tool Creating a screen capture and converting it into a Jpeg fileConversion Method field, select Creating screen capture Select items from the menu on the left Setting up the projector using a Web browserSettings Details on major itemsWhen replacing, always use lamp TLPLW23 sold separately Lamp replacementWhen the lamp is broken About lampLamp replacement Main unit cleaning Lens and main unit cleaningLens cleaning Trouble indicationsTroubleshooting List of general specifications List of supported signals RGB signalsSpecifications Separately sold productSpecifications List of supported signals Component signalsList of supported signals Video, S-Video signals Pin assignment of Computer 2 in & Monitor terminalsPin assignment Main CommandsControl terminal Interface format
Top Page Image Contents