Security, User Password, Admin Password | Rugged Outback ELX4-60

BASIC CONFIGURATION

ELX4 -60

5.7.5. Security

User Password

Designate a User’s Password for access to monitoring and playback. Default password is “0000”.

Admin Password

Designate an Administrator’s Password to control access to Configuration Menu and full system control authority. Default password is “9999”

Remote Setup

When set to “Enable,” users can configure ELX4 -60 through the S/W interface from a remote site via network.

Remote Relay

Enables access to the “Relay” menu from a remote site.

Rugged CCTV

2003.05.21 (v 1.0)

41

Image 41

Rugged Outback ELX4-60 manual Security, User Password, Admin Password, Remote Setup, Remote Relay

Contents

User’s Guide Cctv Monitor User ELX4-60 FCC Compliance Statement Important Notice Rugged Cctv ELX4 Setting at Text menu Setting at Serial Setup’s RS232 menu Appendix #2 Utilizing IP Addresses on Local Network Introduction What is ELX4-60? ELX4-60 Key features Front Panel Product Description DIO Rear Panel Installation Summary Viewing basic screen Quad-split MonitoringViewing single full screen Viewing multi screen Viewing all channels with sequence mode Viewing with connected PTZ Viewing an alarm triggered channelViewing images with Digital Zoom Save Preset Load PresetPan/Tilt Control Zoom/Focus Control Using Screen Lock Using RelayPlayback via various mode Playback Various playback modes Playback via split screenPlayback with Digital Zoom Button control Using Search Mode Copy Image Copy / Backup / Delete Data ManagerSeconds Select Disk Start Date & Time / End Date & Time Backup Manager Quick Setup ConfigurationDelete Data Date/Time Daylight Saving Time ZoneTime Format Date/Time Recording Channel Status Configuration StatusRecording Speed/Quality Audio Recording Name Camera Analog Camera Channels Ch ~ Ch TIP Type StatusColor Gain/Brightness/Contrast Time Schedule Normal Rec. Analog Camera Channels Ch ~ Ch Weekday Start/End Setting Time ScheduleDay Start/End Special Time Recording Event Recording Setting Special Time Sensor 1/2/3/4 Alarm Rec. Analog Camera Channels Ch ~ ChMD Area Text Setting MD AreaPre Alarm sec Post Alarm sec Special Time SetupRelay Monitor Seq. SwitchingsecAlarm Pop-up/Pop-up Holdsec Audio System Recording / Monitoring TextSync Text With Device Seek Header Timeout msDelimiter Lines To designate Weekday/Weekend and Day/Night Time Schedule Special Time Admin Password User PasswordRemote Setup Security Auto Del. Alarm Disk SetupBackup Reminder Auto Del. Normal Network Network DNS Server IP Address IP Address, NetMask, and Gateway Address XDSL User ID/Password HRS Interval HRS Group ID Firewall / Port Monitoring Port / Playback PortTP Server Port Baud rate/Parity/Stop bit/Data bit Serial SetupInterface Miscellaneous Remote Control IDHow to register remote controller Reset Values Alarm BuzzerKeyboard Control Addr Keyboard PTZ Addr Utility Disk Manager Type Activating IP Cam menus Using IP Cam Configuration Camera Setting IP Camera Channels Ch ~ Ch Band Width LimitKB/s IP AddressURLPort Select Cam Local IP Cam ListSearch Normal Rec. IP Camera Channels Ch ~ Ch IP Cam Event Alarm Rec. IP Cam Channel Ch ~ ChRecording Speed/Quality & Pre Alarm & Post Alarm Setting at Text menu Connecting External DeviceUsing Text Device Setting at Alarm Rec. menu Setting at Serial Setup’s RS232 menu Setting at Normal Rec. menu Setting at Serial Setup’s PTZ menu Using Keyboard Appendix Appendix #1 Technical Specification Appendix Appendix #2.1 Introduction Appendix #2 Utilizing IP Addresses on Local Network#2.2 IP construction and Network class IP construction #2.3 C-class Network Features of AddressesNetwork configuration To use as one network To use as three sub-networks 1/4 + 1/4 + 1/2 To use as two sub-networks 1/2 + 1/2 To use as four sub-networks 1/4 + 1/4 + 1/4 + 1/4 Appendix