Serial Setup, Interface | Rugged Outback ELX4-60 guide

BASIC CONFIGURATION

ELX4 -60

5.7.8. Serial Setup

There are two RS232 menus (One for external devices connected via the DB -9 pin, and the other for PTZ setting) and one RS 422/485 menu.

Device

Designate the connected external device.

Interface

Used to designate the protocol on the RS422/RS485 Menu.

Baud rate/Parity/Stop (bit)/Data (bit)

Each value should be set according to the specifications of the connected external device.

Rugged CCTV

2003.05.21 (v 1.0)

49

Image 49

Rugged Outback ELX4-60 manual Serial Setup, Interface, Baud rate/Parity/Stop bit/Data bit

Contents

User’s Guide Cctv Monitor User ELX4-60 FCC Compliance Statement Important Notice Rugged Cctv ELX4 Setting at Text menu Setting at Serial Setup’s RS232 menu Appendix #2 Utilizing IP Addresses on Local Network Introduction What is ELX4-60? ELX4-60 Key features Front Panel Product Description DIO Rear Panel Installation Summary Viewing basic screen Quad-split MonitoringViewing single full screen Viewing multi screen Viewing all channels with sequence mode Viewing images with Digital Zoom Viewing an alarm triggered channelViewing with connected PTZ Save Preset Load PresetPan/Tilt Control Zoom/Focus Control Using Screen Lock Using RelayPlayback via various mode Playback Playback with Digital Zoom Playback via split screenVarious playback modes Button control Using Search Mode Copy Image Copy / Backup / Delete Data ManagerSeconds Select Disk Start Date & Time / End Date & Time Backup Manager Quick Setup ConfigurationDelete Data Date/Time Daylight Saving Time ZoneTime Format Date/Time Recording Channel Status Configuration StatusRecording Speed/Quality Audio Recording Name Camera Analog Camera Channels Ch ~ Ch TIP Type StatusColor Gain/Brightness/Contrast Time Schedule Normal Rec. Analog Camera Channels Ch ~ Ch Weekday Start/End Setting Time ScheduleDay Start/End Special Time Recording Event Recording Setting Special Time MD Area Alarm Rec. Analog Camera Channels Ch ~ ChSensor 1/2/3/4 Pre Alarm sec Setting MD AreaText Post Alarm sec Relay SetupSpecial Time Alarm Pop-up/Pop-up Holdsec Seq. SwitchingsecMonitor Audio System Recording / Monitoring TextSync Text With Device Seek Header Timeout msDelimiter Lines To designate Weekday/Weekend and Day/Night Time Schedule Special Time Admin Password User PasswordRemote Setup Security Auto Del. Alarm Disk SetupBackup Reminder Auto Del. Normal Network Network DNS Server IP Address IP Address, NetMask, and Gateway Address XDSL User ID/Password HRS Interval HRS Group ID TP Server Port Monitoring Port / Playback PortFirewall / Port Interface Serial SetupBaud rate/Parity/Stop bit/Data bit How to register remote controller Remote Control IDMiscellaneous Reset Values Alarm BuzzerKeyboard Control Addr Keyboard PTZ Addr Utility Disk Manager Type Activating IP Cam menus Using IP Cam Configuration Camera Setting IP Camera Channels Ch ~ Ch Port IP AddressURLBand Width LimitKB/s Search Local IP Cam ListSelect Cam Normal Rec. IP Camera Channels Ch ~ Ch Recording Speed/Quality & Pre Alarm & Post Alarm Alarm Rec. IP Cam Channel Ch ~ ChIP Cam Event Using Text Device Connecting External DeviceSetting at Text menu Setting at Alarm Rec. menu Setting at Serial Setup’s RS232 menu Setting at Normal Rec. menu Setting at Serial Setup’s PTZ menu Using Keyboard Appendix Appendix #1 Technical Specification Appendix Appendix #2.1 Introduction Appendix #2 Utilizing IP Addresses on Local Network#2.2 IP construction and Network class IP construction Network configuration To use as one network Features of Addresses#2.3 C-class Network To use as three sub-networks 1/4 + 1/4 + 1/2 To use as two sub-networks 1/2 + 1/2 To use as four sub-networks 1/4 + 1/4 + 1/4 + 1/4 Appendix