System, Audio | Rugged Outback ELX4-60 instruction

ELX4 -60

BASIC CONFIGURATION

5.7. System

5.7.1. Audio

ELX4-60 supports one channel audio input. This single audio channel can be replayed with any connected channel or with all of them.

Recording

Set to “On” using the [ENTER] button and the [ARROW] buttons to record audio.

Audio Gain

Increases or decreases the sensitivity to the audio signal. Can be set between –7 and +8.

+20dB

To amplify the audio input signal. Should ONLY be used when using an external microphone .

Sync Audio with

Designate which channel(s) to synchronize audio with during playback.

36

2003.05.21 (v 1.0)

Rugged CCTV

Image 36

Rugged Outback ELX4-60 manual System, Audio

Contents

ELX4-60 User’s Guide Cctv Monitor User FCC Compliance Statement Important Notice ELX4 Rugged Cctv Setting at Text menu Setting at Serial Setup’s RS232 menu Appendix #2 Utilizing IP Addresses on Local Network What is ELX4-60? Introduction Key features ELX4-60 Product Description Front Panel Rear Panel DIO Installation Summary Monitoring Viewing basic screen Quad-splitViewing single full screen Viewing multi screen Viewing all channels with sequence mode Viewing an alarm triggered channel Viewing images with Digital ZoomViewing with connected PTZ Load Preset Save PresetPan/Tilt Control Zoom/Focus Control Using Relay Using Screen LockPlayback via various mode Playback Playback via split screen Playback with Digital ZoomVarious playback modes Using Search Mode Button control Copy / Backup / Delete Data Manager Copy ImageSeconds Select Disk Backup Manager Start Date & Time / End Date & Time Configuration Quick SetupDelete Data Date/Time Time Zone Daylight SavingTime Format Date/Time Recording Configuration Status Channel StatusRecording Speed/Quality Audio Recording Camera Analog Camera Channels Ch ~ Ch Name TIP Status TypeColor Gain/Brightness/Contrast Normal Rec. Analog Camera Channels Ch ~ Ch Time Schedule Setting Time Schedule Weekday Start/EndDay Start/End Special Time Recording Setting Special Time Event Recording Alarm Rec. Analog Camera Channels Ch ~ Ch MD AreaSensor 1/2/3/4 Setting MD Area Pre Alarm secText Post Alarm sec Setup RelaySpecial Time Seq. Switchingsec Alarm Pop-up/Pop-up HoldsecMonitor System Audio Text Recording / MonitoringSync Text With Device Timeout ms Seek HeaderDelimiter Lines Time Schedule To designate Weekday/Weekend and Day/Night Special Time User Password Admin PasswordRemote Setup Security Disk Setup Auto Del. AlarmBackup Reminder Auto Del. Normal Network Network IP Address, NetMask, and Gateway Address DNS Server IP Address User ID/Password XDSL HRS HRS Interval Group ID Monitoring Port / Playback Port TP Server PortFirewall / Port Serial Setup InterfaceBaud rate/Parity/Stop bit/Data bit Remote Control ID How to register remote controllerMiscellaneous Alarm Buzzer Reset ValuesKeyboard Control Addr Keyboard PTZ Addr Utility Disk Manager Type Using IP Cam Activating IP Cam menus Camera Setting IP Camera Channels Ch ~ Ch Configuration IP AddressURL PortBand Width LimitKB/s Local IP Cam List SearchSelect Cam Normal Rec. IP Camera Channels Ch ~ Ch Alarm Rec. IP Cam Channel Ch ~ Ch Recording Speed/Quality & Pre Alarm & Post AlarmIP Cam Event Connecting External Device Using Text DeviceSetting at Text menu Setting at Serial Setup’s RS232 menu Setting at Alarm Rec. menu Setting at Normal Rec. menu Using Keyboard Setting at Serial Setup’s PTZ menu Appendix Appendix #1 Technical Specification Appendix Appendix Appendix #2 Utilizing IP Addresses on Local Network #2.1 Introduction#2.2 IP construction and Network class IP construction Features of Addresses Network configuration To use as one network#2.3 C-class Network To use as two sub-networks 1/2 + 1/2 To use as three sub-networks 1/4 + 1/4 + 1/2 To use as four sub-networks 1/4 + 1/4 + 1/4 + 1/4 Appendix