Alarm Rec. Analog Camera Channels Ch ~ Ch | Rugged Outback ELX4-60

BASIC CONFIGURATION

ELX4 -60

5.4. Alarm Rec. – Analog Camera Channels (Ch. 1 ~ Ch. 4)

This menu is to configure for the setting s for alarm recording condition s. To activate this schedule, set “Event Recording” under the “Normal Recording” tab to “On.”

MD

Choose from among four sensitivity conditions; Off, Low, Standard, High.

MD Area

Customize the MD area.

Default value is “Select All”. Select “Custom Area” to remove certain blocks from detecting motion.

Sensor 1/2/3/4

The ELX4-60 will only work with NO (Normal Open) sensors. If sensors are connected, turn each sensor “On.”

Rugged CCTV

2003.05.21 (v 1.0)

31

Image 31

Rugged Outback ELX4-60 manual Alarm Rec. Analog Camera Channels Ch ~ Ch, MD Area, Sensor 1/2/3/4

Contents

User’s Guide Cctv Monitor User ELX4-60 FCC Compliance Statement Important Notice Rugged Cctv ELX4 Setting at Text menu Setting at Serial Setup’s RS232 menu Appendix #2 Utilizing IP Addresses on Local Network Introduction What is ELX4-60? ELX4-60 Key features Front Panel Product Description DIO Rear Panel Installation Summary Viewing multi screen MonitoringViewing basic screen Quad-split Viewing single full screen Viewing all channels with sequence mode Viewing images with Digital Zoom Viewing an alarm triggered channelViewing with connected PTZ Zoom/Focus Control Load PresetSave Preset Pan/Tilt Control Playback Using RelayUsing Screen Lock Playback via various mode Playback with Digital Zoom Playback via split screenVarious playback modes Button control Using Search Mode Select Disk Copy / Backup / Delete Data ManagerCopy Image Seconds Start Date & Time / End Date & Time Backup Manager Date/Time ConfigurationQuick Setup Delete Data Date/Time Time ZoneDaylight Saving Time Format Recording Audio Recording Configuration StatusChannel Status Recording Speed/Quality Name Camera Analog Camera Channels Ch ~ Ch TIP Gain/Brightness/Contrast StatusType Color Time Schedule Normal Rec. Analog Camera Channels Ch ~ Ch Special Time Recording Setting Time ScheduleWeekday Start/End Day Start/End Event Recording Setting Special Time MD Area Alarm Rec. Analog Camera Channels Ch ~ ChSensor 1/2/3/4 Pre Alarm sec Setting MD AreaText Post Alarm sec Relay SetupSpecial Time Alarm Pop-up/Pop-up Holdsec Seq. SwitchingsecMonitor Audio System Device TextRecording / Monitoring Sync Text With Lines Timeout msSeek Header Delimiter To designate Weekday/Weekend and Day/Night Time Schedule Special Time Security User PasswordAdmin Password Remote Setup Auto Del. Normal Disk SetupAuto Del. Alarm Backup Reminder Network Network DNS Server IP Address IP Address, NetMask, and Gateway Address XDSL User ID/Password HRS Interval HRS Group ID TP Server Port Monitoring Port / Playback PortFirewall / Port Interface Serial SetupBaud rate/Parity/Stop bit/Data bit How to register remote controller Remote Control IDMiscellaneous Keyboard PTZ Addr Alarm BuzzerReset Values Keyboard Control Addr Utility Disk Manager Type Activating IP Cam menus Using IP Cam Configuration Camera Setting IP Camera Channels Ch ~ Ch Port IP AddressURLBand Width LimitKB/s Search Local IP Cam ListSelect Cam Normal Rec. IP Camera Channels Ch ~ Ch Recording Speed/Quality & Pre Alarm & Post Alarm Alarm Rec. IP Cam Channel Ch ~ ChIP Cam Event Using Text Device Connecting External DeviceSetting at Text menu Setting at Alarm Rec. menu Setting at Serial Setup’s RS232 menu Setting at Normal Rec. menu Setting at Serial Setup’s PTZ menu Using Keyboard Appendix Appendix #1 Technical Specification Appendix Appendix IP construction Appendix #2 Utilizing IP Addresses on Local Network#2.1 Introduction #2.2 IP construction and Network class Network configuration To use as one network Features of Addresses#2.3 C-class Network To use as three sub-networks 1/4 + 1/4 + 1/2 To use as two sub-networks 1/2 + 1/2 To use as four sub-networks 1/4 + 1/4 + 1/4 + 1/4 Appendix