Relay, Setup, Special Time | Rugged Outback ELX4-60 guide

ELX4 -60

BASIC CONFIGURATION

5.5. Relay

This menu is to set the relay commands according to each time schedule. Relay commands are only used with events triggered with the four analog channels.

Setup

Alarm triggered events (MD or Sensors) can be set to trigger Relays 1 through 4. When set, the event will trigger the corresponding digital output.

Special Time

Enable “Special Time” to apply the relay schedule to the Special Time Zone.

34

2003.05.21 (v 1.0)

Rugged CCTV

Image 34

Rugged Outback ELX4-60 manual Relay, Setup, Special Time

Contents

ELX4-60 User’s Guide Cctv Monitor User FCC Compliance Statement Important Notice ELX4 Rugged Cctv Setting at Text menu Setting at Serial Setup’s RS232 menu Appendix #2 Utilizing IP Addresses on Local Network What is ELX4-60? Introduction Key features ELX4-60 Product Description Front Panel Rear Panel DIO Installation Summary Viewing single full screen MonitoringViewing basic screen Quad-split Viewing multi screen Viewing all channels with sequence mode Viewing images with Digital Zoom Viewing an alarm triggered channelViewing with connected PTZ Pan/Tilt Control Load PresetSave Preset Zoom/Focus Control Playback via various mode Using RelayUsing Screen Lock Playback Playback with Digital Zoom Playback via split screenVarious playback modes Using Search Mode Button control Seconds Copy / Backup / Delete Data ManagerCopy Image Select Disk Backup Manager Start Date & Time / End Date & Time Delete Data ConfigurationQuick Setup Date/Time Time Format Time ZoneDaylight Saving Date/Time Recording Recording Speed/Quality Configuration StatusChannel Status Audio Recording Camera Analog Camera Channels Ch ~ Ch Name TIP Color StatusType Gain/Brightness/Contrast Normal Rec. Analog Camera Channels Ch ~ Ch Time Schedule Day Start/End Setting Time ScheduleWeekday Start/End Special Time Recording Setting Special Time Event Recording MD Area Alarm Rec. Analog Camera Channels Ch ~ ChSensor 1/2/3/4 Pre Alarm sec Setting MD AreaText Post Alarm sec Relay SetupSpecial Time Alarm Pop-up/Pop-up Holdsec Seq. SwitchingsecMonitor System Audio Sync Text With TextRecording / Monitoring Device Delimiter Timeout msSeek Header Lines Time Schedule To designate Weekday/Weekend and Day/Night Special Time Remote Setup User PasswordAdmin Password Security Backup Reminder Disk SetupAuto Del. Alarm Auto Del. Normal Network Network IP Address, NetMask, and Gateway Address DNS Server IP Address User ID/Password XDSL HRS HRS Interval Group ID TP Server Port Monitoring Port / Playback PortFirewall / Port Interface Serial SetupBaud rate/Parity/Stop bit/Data bit How to register remote controller Remote Control IDMiscellaneous Keyboard Control Addr Alarm BuzzerReset Values Keyboard PTZ Addr Utility Disk Manager Type Using IP Cam Activating IP Cam menus Camera Setting IP Camera Channels Ch ~ Ch Configuration Port IP AddressURLBand Width LimitKB/s Search Local IP Cam ListSelect Cam Normal Rec. IP Camera Channels Ch ~ Ch Recording Speed/Quality & Pre Alarm & Post Alarm Alarm Rec. IP Cam Channel Ch ~ ChIP Cam Event Using Text Device Connecting External DeviceSetting at Text menu Setting at Serial Setup’s RS232 menu Setting at Alarm Rec. menu Setting at Normal Rec. menu Using Keyboard Setting at Serial Setup’s PTZ menu Appendix Appendix #1 Technical Specification Appendix Appendix #2.2 IP construction and Network class Appendix #2 Utilizing IP Addresses on Local Network#2.1 Introduction IP construction Network configuration To use as one network Features of Addresses#2.3 C-class Network To use as two sub-networks 1/2 + 1/2 To use as three sub-networks 1/4 + 1/4 + 1/2 To use as four sub-networks 1/4 + 1/4 + 1/4 + 1/4 Appendix