Toshiba TDP-S81 Connection, Placement Styles, Before connection, Projection Distance and Size

Page 11

Placement

Placement Styles

As shown in the figures below, this device can be placed in 4 different styles.

The factory setting is “floor-mounted front projection.” Set the Projection mode in the default setting menu p.32 , in accordance with your needs.

Floor-mounted front projection

Floor-mounted rear projection

Connection

Before connection

Read the owner’s manual of the device you are connecting to the projector.

Some types of computer cannot be used or connected to this projector. Check for an RGB output terminal, supported signal p.45 , etc.

Turn off the power of both devices before connecting.

The figure below is a sample connection. This does not mean that all of these devices can or must be connected simultaneously. (Dotted lines mean items can be exchanged.)

Computer (for control)

Audio amplifier, etc.

 

Ceiling-mounted front projection

 

Ceiling-mounted rear projection

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

WARNING

Always obey the instructions listed in IMPORTANT SAFETY INSTRUCTIONS when placing the unit. Attempting to clean/replace the lamp at a high site by yourself may cause you to drop down, thus resulting in injury.

If you wish to mount the projector on the ceiling, be sure to ask your dealer to do so. Mounting the projector on a ceiling requires special ceiling brackets (sold separately) and specialized knowledge. Improper mounting could cause the projector to fall, resulting in an accident.

If the projector is ceiling-mounted, install the breaker for turning off the power in case of anomaly. Let everyone involved with the use of the projector know that fact.

 

 

VCR

 

Video recorder,

 

 

 

DVD player, etc.

To RS-232C

 

To audio output

To video

To audio output

To S-Video

p.47

White (L)/Red (R)

output

White (L)/Red (R)

output

terminal

 

 

Video cable (not supplied)

 

 

 

 

 

 

Control cable

 

 

 

 

 

AV cable

 

S-Video cable

 

 

 

(not supplied)

 

(not supplied)

 

Audio cable

To audio input

White (L)/Red (R)

(not supplied)

 

Preparations

Projection Distance and Size

Use the figures, tables, and formulas below to determine the projection size and projection distance. (Projection sizes are approximate values for full-size picture with no keystone adjustment.)

Screen As seen from above

a (min length) = projection size (inches) 0.04064

90°

a (max length) = projection size (inches) 0.04878

RGB cable

Audio cable

 

 

 

RGB cable

(not supplied)

 

 

Audio cable

(not supplied)

 

 

 

 

 

 

(not supplied)

(supplied)

 

 

Monitor cable Mini

 

 

 

To RGB

 

D-sub 15P-BNC

RGB cable

To audio output

To RGB output

output

 

(not supplied)

 

 

 

 

 

(supplied with

 

 

 

 

 

TDP-S81)

 

 

 

To audio

To Y/CB/CR output

 

 

 

 

Green (Y)/Blue (CB)/Red (CR)

 

 

 

 

output

 

 

 

 

 

Conversion adapter BNC-pin

 

 

 

 

 

(not supplied)

 

 

 

As seen from the side

Lens center

H

90°

a

a is the distance (m) between the lens and the screen, and corresponds to a range of 1.20 m to

10.00m. H is the height from the image bottom to the center of the lens.

projection

projection distance a (m)

height (H)

size (inches)

min length

max length

(cm)

(zooming max)

(zooming min)

24.6

1.20

12.8

40

1.62

1.95

20.2

60

2.44

2.93

30.0

80

3.25

3.90

40.2

100

4.06

4.88

50.3

150

6.10

7.32

75.4

200

8.13

9.76

100.6

246

10.00

123.8

Computer

DVD video recorder, etc.

Document camera

Computer

Notes

COMPUTER terminals 1 and 2 function identically.

For TDP-S81, the document camera should be connected to COMPUTER terminal 2.

The AUDIO IN terminal doubles for devices connected to COMPUTER terminals 1 and 2.

20

21

Image 11
Contents TDP-S81SVGA/ With Document Camera Others Maintenance Operations Preparations Before UsingUSA only Safety PrecautionsUsing BeforeBefore Using Important Safety InstructionsImportant Safety Instructions Save Original Packing Materials Power Supply Cord SelectionImportant Precautions Place and Manner of InstallationOther Cautions and Informations Remote Control BatteriesExemption Clauses Contents Names of each part on the main unit Checking the package contentsEquipment Component video signal Y/PB/PR from videoParts on the rear panel 14 13Names of each part on the document camera TDP-S81 Preparing and using the remote controlLoading dry-cell batteries into the remote control Operating the remote controlBefore connection PlacementPlacement Styles ConnectionOperations Turning the power on and offBasic operations Correcting the keystone distortion Using handy featuresUsing auto setting Cutting off the picture and sound temporarily Mute Using the menusUsing handy features How to use the menusDisplay setting menu Using the menuImage adjustment menu Sets the lamp power Low Default setting menuNo signal Power onHow to use the document camera Using the document cameraLocking the white balance Using the document cameraImage projection with the document camera About lamp Lamp replacementMaintenance Trouble indications Lens and main unit cleaningLamp replacement Others Before calling service personnelList of supported signals RGB signals SpecificationsList of general specifications Document camera specifications TDP-S81Separately sold product SpecificationsList of supported signals Y/PB/PR signals List of supported signals Video, S-Video signals