Toshiba TLP-XC2000 Power Supply Cord Selection, Important Precautions, Moisture Condensation

Page 5

IMPORTANT SAFETY INSTRUCTIONS (Continued)

POWER SUPPLY CORD SELECTION

19. Replacement Parts

When replacement parts are required, be sure the service technician has used replacement parts specified by the manufacturer or have the same characteristics as the original part. Unauthorized substitutions may result in fire, electric shock, or other hazards.

(Replacement of the lamp only should be made by users.)

20. Safety Check

Upon completion of any service or repairs to this product, ask the service technician to perform safety checks to determine that the product is in proper operating condition.

23.Do not look into the laser light source of the remote control or direct the laser pointer toward a person or

a mirror.

The laser beam may cause damage to the eyes or sight.

24.Do not get your hands between the camera arm and the main unit when setting the camera arm

back in its original position. (Models equipped

with document camera)

To avoid injury, be careful not to get your hands caught when setting the camera arm back in its original position.

Families with children should be particularly careful.

If your line voltage is 220 to 240V, use one of the following types of cable.

 

Using

Plug

 

Plug

 

configuration Plug type

Line voltage

configuration Plug type

Line voltage

 

EURO

220 – 240V

Australian

200 – 240V

Before

240V

 

 

 

 

 

 

 

 

 

10A

 

 

UK

220 – 240V

Switzerland

200 – 240V

 

240V

 

 

 

 

6A

 

 

Use a 5A fuse which is approved by ASTA

North American

200 – 240V

 

or BSI to BSI362.

 

 

Always replace the fuse cover after

240V

15A

changing the fuse.

 

IMPORTANT PRECAUTIONS

Save Original Packing Materials

The original shipping carton and packing materials will come in handy if you ever have to ship your projector. For maximum protection, repack the set as it was originally packed at the factory.

21.Do not leave thermal- paper documents or easily deformed items on top of the unit or near the air exhaust for long periods

of time.

The heat from the unit could erase the information on the thermal paper, or cause deformation or warping.

22. Do not use the product in a closed installation state.

Do not place the product in a box or in any other closed installation state. Otherwise it may overheat. This could result in a risk of fire.

25.Do not carry by the camera arm. (Models

equipped with document camera)

Do not carry the projector by the camera arm. Doing so can result in damage or injury.

26.Do not move the projector while the arm is still erect.

(Models equipped with document camera)

Always store the arm back in position when moving the projector. Otherwise injury or damage may result.

Moisture Condensation

Never operate this unit immediately after moving it from a cold location to a warm location. When the unit is exposed to such a change in temperature, moisture may condense on the lens and the crucial internal parts. To prevent the unit from possible damage, do not use the unit for at least 2 hours when there is an extreme or sudden change in tempera- ture.

Place and Manner of Installation

Do not place in hot locations, such as near heating equipment. Doing so could cause malfunction, and shorten the life of the projector.

Avoid locations with oil or cigarette smoke. Doing so will dirty the optical parts, shortening their lives, and darkening the screen.

Do not use this product in the upright position or tilt it up or down by more than 20° from level. Doing so may cause a failure or shorten the life of the product.

Using this instrument near a TV or radio may cause interference to the images or audio sound. If this happens, move it away from the TV or radio.

Moving the projector from a low-temperature room to a high-temperature room may cause condensation on the lens or internal parts in the instrument. If you continue to use it in that situation, the malfunction may result. Ensure to wait until the condensation naturally disappears.

In a high altitude location where air is thin, cooling efficiency is reduced so use the projector with [Fan mode] set to [High]. p.43

8

9

Image 5
Contents TLP-X2000 USA only Safety PrecautionsImportant Safety Instructions Important Safety Instructions Important Precautions Power Supply Cord SelectionPlace and Manner of Installation Save Original Packing MaterialsOther Cautions and Informations Remote Control BatteriesExemption Clauses Contents Names of each part on the main unit Checking the package contentsRemote control Remote Control TLP-X2000Remote Control TLP-XC2000 Control panelCamera Names of the terminals on the rear panelLoading dry-cell batteries into the remote control Preparing and using the remote controlOperating the remote control Connecting a computerPlacement Styles PlacementConnection Before connectionConnection Turning the power on and offLabel locations Basic operations Turning the power on and offBasic operation Using handy featuresChanging picture mode Using handy featuresResizing image Cutting off the picture and sound temporarily MuteFreezing the image Freeze Setting the passwordChanging screen size Select OFF Select OK and press the button Image adjustment menu Using the menusHow to use the menus Detailed description Screen size Using the menusDisplay setting menu Precaution Blackboard modeReset logo Up/down shiftDefault setting 2 menu Default setting menuDefault setting 1 menu Displaying Information Status display Using the document cameraPreparation of the document camera Key lockImage projection with the document camera Using the document cameraAbout lamp When the lamp is brokenLocking the white balance Press W.BALANCE button and lock the white BalanceLamp replacement Lens and main unit cleaning Air filter cleaningTrouble indications Before calling service personnelList of general specifications SpecificationsList of supported signals RGB signals SpecificationList of supported signals Y/PB/PR signals SpecificationsList of supported signals Video, S-Video signals Separately sold product