Toshiba TLP780U TLP781U Limited two 2 Years Warranty of Parts and Labor, Your Responsibility

Page 81

LIMITED WARRANTY

CONTENTS

81

TOSHIBA 3LCD Data Projector (TLP780 Series)

Toshiba America Consumer Products, Inc. (TACP) makes the following limited warranties.

These limited warranties extend to the original end-user purchaser.

as limited above and do not extend to any product or parts which have been lost or discarded by you or to damage to products or parts caused by misuse, accident, improper installation, improper maintenance or use in violation of instructions furnished by us; or to units which have been altered or modified without authorized of TACP or to damage to product or parts thereof which have had the serial number removed, altered, defaced or rendered illegible.

Limited two (2) Years Warranty of Parts and Labor

TACP warrants this product and its parts against defects in materials or workmanship for a period of two years after the date of original retail purchase.

For a period of two years after the date of original retail purchase, TACP will repair a defective product or a part, without charge to you.

This warranty also covers accessories of 3LCD Data Projector.

This warranty period of the lamp is ninety (90) days.

Your Responsibility

The above warranties are subject to the following conditions.

1.You must retain your bill of sale or provide other proof of purchase.

2.You must make a written notification within thirty (30) days after your discovery of a defective product or part.

3.All warranty servicing of this product or parts must be made by TACP or a service facility authorized by TACP.

4.These warranties are effective only if the product is purchased and operated in the USA.

5.Labor service charges for installation and adjustment of customer controls are not covered by this warranty.

6.Warranties extend only to defects in materials or workmanship

7.If it is determined after investigation that the claimed problem was not covered with this warranty, you shall pay the cost of investigation at prevailing rate.

Step-by-step procedure how to obtain warranty service

To obtain warranty servicing, you should:

1.Read the owners manual thoroughly before operating.

2.Please contact your dealer for an immediate service and an advice.

3.If your dealer is not able to assist you, please contact TACP Service Center listed below or a servicing facilities authorized by TACP for a warranty service within thirty (30) days after you find a defective product or part.

4.Arrange for a delivery of the product to TACP Service Center or a servicing facilities authorized by TACP.

5.The shipment of the product must be insured, safely and securely packed, preferably in the original carton or a carton with an equivalent protection. A letter explaining the defect and also a copy of the bill of sale or other proof of purchase must be enclosed. All transportation and insurance charges must be prepaid by you.

Others

Continued

Image 81
Contents TLP780U Safety Precautions Important Precautions Important Safety Instructions Heat Important Safety InstructionsObject and Liquid Entry Damage Requiring Service Strong light may cause damage to your eyes or sight Do not carry by the camera armPower supply cord selection Contents Names of each part on the main unit Explanation here is only for the model without the documentRefer to Names of each part on the main unit Top sideMenu button Input button Right side Names of each part on the remote control Loading batteries Install the batteriesOpen the cover Attach the coverRemote control operation Front sideRear side Viewer Floor-mounted projector placementDetermine the screen size projected on the screen Top viewSide view Light Orange Power cord Supplied Connect the power cordTake off the lens cover Insert the other end into a wall outletFoot adjuster Foot adjuster release button Projector placement angle adjustmentLift up Lower Turn clockwise to lift up Turn counterclockwise to lowerViewer Translucent screen Ceiling-mounted projector placementConnecting a computer Computer in 1 connector Connecting a computer Computer in 2 connector Connecting video equipment Connectionsand Computer Projector operation control by a computerHow to use the output connector Projection on the screen Press ON/STANDBYLamp lights and the start up display appears Press Enter to confirm Turn on the connected equipment and put it in playback modeLanguage Dialog box to find and designate this filePress Input and hold for two seconds Select the input source by pressing Input repeatedlyPress Enter Input source selection menu appearsFocusing ring Adjust the picture size by turningStill picture is recommended for focusing Zooming leverAbout the LCD Panel Press VOL/ADJ +/- to adjust volumeTurning the power off Press ON/STANDBY after using the projectorPress ON/STANDBY again Input full screen video signals from the input Adjusting the picture automaticallySource computer and project the image Press Auto SETCorrecting the keystone distortion Press KeystoneConfirm the keystone distortion After confirming that V-keystone is selected on the menu Keystone adjustment finishesCutting off the picture and sound temporarily Icon appears in the mute modePress Mute Sound and picture are cut off temporarilyFreezing the picture Icon appears in the freeze modePress Freeze Picture freezesIcon appears in the resize mode Enlarging the picture sizePress Resize Displaying PIP Sub-pictures Press PIPSub-picture is displayed Press Call Displaying InformationOperating a computer by the remote control Press Menu Operating the menu screenPress Menu once again Select the item with the selection ButtonsSelect the item with selection buttons Adjust with VOL/ADJ +Enter Press Enter Press EnterShutter Guide Menu adjustments and settingsFull Menu adjustments and settings Picture Full Menu adjustments Position Full Menu adjustments Color Full Menu adjustments and settings Audio Settings Adjustments Full Menu adjustments and settings DisplayFull Menu settings Default setting Reset all Full Menu settings ResetPIP menu setting ImagingDocument camera Preparation of the document imaging camera Press ARM Light Set a document to be projectedCamera head over them Move the camera head to adjust the size of the picture Press Camera to select the camera input modePress Camera Gain +/- to improve view of a When finished, turn off the light and close itCamera subject which is too dark or vivid Put back the armOverlaying projection Locking the white balance Balance Press W.BALANCE to turn the Lock indicatorProject a white paper and enlarge it to fill ScreenWith the document camera operating, fully Correcting illuminated defectsCover the camera lens with a piece of black Paper or clothMain unit side Trouble indicationsUnplug the power cord Take off the air filter cover Air filter cleaningClean the air filter Detach the air filterAssemble the air filter Mount the air filter coverAir filter Air filter cover Cleaning the lens Lens and main unit cleaningCleaning the main unit Replacing the intake, exhaust fans and air filterUnplug the power cord Wait until the lamp gets cool enough Lamp replacementTake off the lamp cover on the bottom panel Pull out the lampLoad a new lamp Reset the lamp timerAttach the lamp cover Slide the cover into place and tighten the two screwsSymptom Cause Correction Before calling service personalBefore calling service personal Do not connect anything Mini D-sub 15pin ConnectorApplicable computer signal Applicable signalSignal Timing Horizontal Signal Timing Vertical Timing chartApplicable signal Compatible Video and S-Video signalCompatible components video signal Y/PB/PR Controlling the projector by using RS-232C Signal assignment of RS-232C Interface formatCommand list Controlling the projector by using RS-232C VCL MO0 MS0 PIP Main unit SpecificationsLiquid crystal display Projection lensAccessories SpecificationsReplacement lamp Sold separatelyLimited two 2 Years Warranty of Parts and Labor Step-by-step procedure how to obtain warranty serviceYour Responsibility Limited Warranty