Toshiba 1600XP manual System Fault Messages, Display Meaning Action

Page 70

System Fault Messages

A Fault message is generated when either a fault condition occurs, or a warning condition occurs three times within ten minutes. The table below shows the possible fault messages and what actions need be taken.

If the input voltage is normal when the fault occurs then the UPS will switch immediately to the bypass mode to continuously feed power to the load.

If the fault condition occurs while the input power is abnormal and the UPS is in Bypass mode the UPS will shut down the output to prevent load equipment damage.

When a Fault condition exists, the red LED on the UPS display panel will illuminate until the fault is cleared.

Display

Meaning

Action

BYPOH

Bypass Overheat – Overheating

Check unit for blocked or in-operable fan. Lower am-

 

condition occurred.

bient temperature if it is greater than 104 °F (40 °C).

 

 

Bypass operation will also cease if overheat condition

 

 

is not corrected within 1 hr. of inverter shutdown. Try

 

 

restarting. If condition re-occurs plan for total shut-

 

 

down and call for service.

BYPOL

Bypass Overload – UPS is over-

Shut down excess equipment to reduce load.

 

loaded.

 

CHRGOV

Charger Overvoltage – Charger

UPS is possibly faulty. Check the UPS operation

 

overvoltage condition occurred.

conditions at time of fault. Not advisable to restart the

 

 

UPS. Call for service.

CLMT

Current Limit – Load on UPS out-

Reduce load on UPS output.

 

put exceeds unit specifications.

 

DCIB

DC Bus Imbalance – DC voltage

Possible causes are UPS fault are connection of half-

 

imbalance occurred.

wave rectifier load. Check load and try restarting. If

 

 

condition persists, call for service.

DCOC

DC Bus Overcurrent – DC overcur-

UPS is possibly faulty. Check the UPS operation

 

rent condition occurred.

conditions at time of fault. Not advisable to restart the

 

 

UPS. Call for service.

DCOV

DC Bus Overvoltage – DC over-

UPS is possible faulty, input wiring error, input over-

 

voltage condition occurred.

voltage or connection of a motor load. Try restarting. If

 

 

condition persists call for service.

DCUVBS

DC Bus Undervoltage during

UPS is possibly faulty. Check the UPS operation

 

Boostup Mode – DC Bus under-

conditions at time of fault. Not advisable to restart the

 

voltage condition occurred.

UPS. Call for service.

DCUVC

DC Bus Undervoltage During

UPS is possibly faulty. Check the UPS operation

 

Charging Mode – DC Bus under-

conditions at time of fault. Not advisable to restart the

 

voltage condition occurred.

UPS. Call for service.

DVCOH

Device Overheat – Overheating

Reduce equipment load to 100% or less and try

 

condition occurred.

restarting.

FSOPEN

Fuse Open.

Replace fuse.

INVOLNR

Inverter Overload (Not Reset-

Reduce equipment load to 100% or less and manually

 

table) – Output overload condition

restart the UPS.

 

occurred.

 

62

1600XP Series Installation and Operation Manual

Image 70
Contents 1600XP Series Page 60616-005 April Product Use and Warranty Restrictions Qualified Personnel onlyUninterruptible Power System UPS Toshiba Customer Support Center PurposeToshiba Customer Support Center Toshiba International CorporationTable of Contents External Layouts/Dimensions/Shipping Weights Screen Tab Monitor Screen Tab SettingsPreventive Maintenance/Parts Replacement Display and KeysSymbols General Safety InstructionsProhibited Symbol indicates do not take action FCC Class a Notice Signal WordsRegulatory Compliance Statement EMC Directive Class a Note144 Vdc 216 Vdc 288 Vdc 20 a45 a 60 a 80 a 100 a 125 a Qualified personnel shallInstructions Importantes Concernant LA Sécurité To be performed by Qualified Personnel OnlyProduct Description Power BackupPower Conditioning Application and UseUnpacking Inspection/Storage/DisposalInspection StorageInstallation Precautions UPSMetal of Conduit is not AN Acceptable Ground Operating Precautions Conductor Routing and GroundingEquipment Warning Labels Sheet 14 15 16 Connections Terminal BlockWire Size and Tightening Torque Number KVA 10 kVA 14-18 kVA 22 kVA Lb.-in. NmOptional Battery Cabinet Connections UPS Model Battery Cabinet Mccb CapacityRemote Contacts MA rms Vac peak MA peak Pin Signal Function Logic UPSCommunication Interfaces Current Vdc peak MA peakUPS LAN Shutdown Signal Operation RS-232C Pin Symbol DescriptionRemotEye III Network Card UPS Specifications Unit Capacity 6kVA 3.1 kW KVA 5.1 kW KVA 6.8 kW KVA 8.5 kWStandard Models 3.6 10 kva cont’d Battery System Battery Replacement YuasaCapacity KVA 11.9 kW1 KVA 15.3 kW1 KVA 18.7 kW1 Standard Models 14 22 kva cont’d Toshiba Part Number for 51896-FS 60995-FS Battery Pack Capacity KVA 11.9 kW1 KVA 15.3 kW1 KVA 18.7 kW 1Command Options Battery Low Voltage Tolerances Battery Backup Time and Discharge ProcessUPS Capacity Starting/Stopping the UPS Stopping the UPSBattery Recharging On-Line Run operation Operating ModesStatic-Bypass Stop operation Battery Backup On batteries EPO Emergency Power Off FunctionAudible Alarm Functions ConditionFront Panel Layout Display and KeysDisplay Manual Controls 1600 XP Records screens Monitor and Settings screensOperating Keys BATLight Emitting Diodes LED Status IndicatorsEnd Touchscreen Menu Tree Test Faults OperationInput Bypass Batt History Backup System Output DC Bus Ctrl/Cfg Disp/ReyeScreen Tab Main RUN/Stop the UPSQuit Keypad ControlsChange Secu. Lvl WriteScreen Security Passwords & Keypad LoginMimic Display Screen Tab MonitorMonitor Details Mimic Display Settings Screen Tab SettingsKey Cmd ID range Types of Parameters DISP/Reye Block Changing UPS Parameter Settings 240VRecalibrate the Touchscreen USR Settings ParametersAccess Level Sec. Abbreviation ADMToshiba On LCDTab Block Toshiba H3On LCD ERR OUTBYP Batt 503 Discharge Cur Battery Discharge Current Monitor Dvcoh RUNStop ViovUSER, Admin AdminLansd Hist 704 UPS Lifetime UPS Lifetime Remaining Time Settings 719 Total Warnings Total No. Of Warning Settings On LCD On LCD Records Sample record screensSystem Fault Messages Display Meaning ActionSystem Warning Messages Dcer BypuvCall DdcnSystem Status Messages System Mode MessagesDisplay Meaning RO2EEERR PfailRmtsd SyncSystem Protection Functions System Protection FeaturesUPS Protection System Overheating Overcurrent Current Limit OverloadCleaning the Touchscreen Preventive Maintenance/Parts ReplacementPreventive Maintenance Overvoltage OvercurrentParts Replacement Optional Receptacle Panel Installation InstructionsBatt Amb Temp Average lifetime      Internal Maintenance Bypass Optional MB Maintenance Bypass UnitsLED OFF External Maintenance Bypass Unit and Shipping Weights External Layouts/Dimensions/Shipping WeightsDimensional Data Electrical Conduit Knock-out DataExternal Layout for 3.6kVA and 6kVA units Snmp Port Remote Eye Slot Page Index Page Page UPS Page Industrial Division
Related manuals
Manual 100 pages 60.45 Kb

1600XP specifications

The Toshiba 1600XP is an advanced multifunction printer that showcases Toshiba's commitment to innovation and reliability in office technology. Designed to meet the demands of modern businesses, the 1600XP integrates several features and technologies that enhance productivity while ensuring high-quality output.

One of the key characteristics of the Toshiba 1600XP is its impressive speed. Capable of printing up to 16 pages per minute, this printer is well-suited for busy work environments where efficiency is paramount. The first print-out time is remarkably fast, minimizing wait times and allowing users to get back to their tasks quickly.

In addition to its speed, the Toshiba 1600XP boasts exceptional print quality. With a high resolution of up to 1200 x 1200 dpi, it produces sharp, clear text and vibrant images, making it ideal for both document printing and professional presentations. The printer uses advanced laser technology, which contributes to consistent and reliable output over time.

The Toshiba 1600XP also integrates advanced scanning capabilities, allowing users to digitize documents with ease. It offers both color and monochrome scanning options, with various file formats available, including PDF and JPEG. The automatic document feeder (ADF) simplifies the scanning process by enabling batch scanning, increasing productivity for users who frequently digitize materials.

Connectivity options are a significant highlight of the Toshiba 1600XP. It comes equipped with USB and Ethernet interfaces, facilitating seamless integration into any office network. For organizations that value mobility, the printer also supports mobile printing solutions, allowing users to print directly from their smartphones or tablets using popular applications.

Energy efficiency is another important aspect of the Toshiba 1600XP. The device is designed to minimize power consumption without compromising performance. Toshiba has incorporated eco-friendly features that help businesses reduce their carbon footprint, making it a practical choice for environmentally conscious organizations.

In summary, the Toshiba 1600XP is a multifunction printer that excels in speed, print quality, and versatility. With its robust scanning capabilities, extensive connectivity options, and energy-efficient design, the 1600XP stands out as an outstanding solution for businesses looking to enhance their document management processes. Whether it's printing, scanning, or copying, the Toshiba 1600XP delivers excellent performance to meet the needs of any fast-paced office environment.