Siemens 7ML19985AB01 instruction manual Date, P35 = 7, print interval set for 7 minutes, 104

Page 103

Timed Print Out

The OCM-3 can be programmed to periodically print out OCM data (P34/35). A typical print out will have the following format.

Time	hh:mm:ss
Date	dd/mm/yy
Site Number	#
Head	# units
Velocity*	# units
Temperature	# units
Flow Rate	# units
Flow Total	# units

*only for applications using velocity input

When the output is directed to a serial printer, a delay is inserted between each line to allow the printer time to print each line before another is sent. In that way, the simplest of printers may be used without need of XON/OFF or hardware handshaking; only a three wire connection is required. The printer must be at least 40 columns wide. The OCM-3 sends text in upper and lower case. The printer must support both upper and lower case or else treat lower case as if it had been sent in upper case.

The printing interval must divide evenly into the selected units of time for printing to occur at regular intervals.

e.g.	P34	= 1, printer mode set for interval in minutes
	P35	= 7, print interval set for 7 minutes

Printing starts at 7 minutes after the hour and will occur every 7 minutes thereafter until 56 minutes into the hour. The next print out would not occur until 7 minutes into the next hour.

Since the port used for communication is the same as used for normal serial communication, a software switch controls whether or not the display is sent out on the serial port. The switch is controlled by typing ’v’ to allow data transmission or ’w’ to stop it. The Milltronics printer emulation program does this automatically.

If the OCM-3 is connected to a computer programmed for printer emulation, the computer will receive the print out data and display it on the video terminal (refer to Milltronics Utilities Software).

7ML19985AB01

OCM III

104

Image 103

Contents Open channel Contact Smpi Technical Publications at the following address Unit Repair and Excluded LiabilityTable of Contents General Keypad Initial Start Up Fundamental Checks Start UPOperation Appendices Maintenance Error Codes 100 Communications 101 7ML19985AB01OCM Short About thisIf you want to know about Read Product OCM IP65 enclosure Specifications» range 20 or 4-20 mA » resolution » 20 to 50 C -5 to 122 F» CE *, FM, CSA NRTL/C ProgrammerTransducer Temperature SensorCabling Auxiliary Input Communication SoftwareOutput » Belden Installing the OCM-3 InstallationOutline and Mounting OCM-3 Layout OCM-3 System DiagramCustomer device Ground shield at OCM-3 only Installing the TransducerInstalling the Temperature Sensor Ground shield at OCM-3 only Basic Wiring Temperature SensorRelays MA OutputSynchronization AC Power Power ConnectionsDC Power Communicating VIA Computer Installing the Memory BACK-UP BatteryInstalling the Programmer Disconnect power before installing or replacing the batteryGeneral Start UPKeypad English Initial Start UPOCM-3 is asking which language you prefer to communicate LanguageF13 auto zero calibration 160 Completed 7ML19985AB01 P0 language English P1 dimensional units CentimetersF5 ddmmyyyy date October 12 114124-hr. time 114100 Enter new timeFundamental Checks OCM Units OperationMemory Security= constant Flow CalculationDisplay Absolute vs. ratiometricDamping For battery operation, set display lighting to off or auto» P6 * flow rate For battery operation, have relays energizing on alarmExample For relay » 20 mAFlow Rate and Totalizing FAIL-SAFEFlow rate Capacity LoggingViewing the data log Blanking TemperatureTime and Date Reset Emulation ModeAs normal 7ML19985AB01 Flow Velocity InputAuxiliary Head Input Voltage Input Current InputDC Output Diagnostic Aids100% head 4 m, enter 5 m Nominal target range Security access required‘D’ Parameter Listing VelocityOCM ‘F’ Parameter Listing Enter security code Emulation modeKeypad to mA output OCM Linear Velocity ‘P’ Parameter Listing= centimetres = imperial million gallons per day Flowrate Volume= absolute = ratiometric Flow rate units GallonsOCM = 4-20 mA = 0-20 mA 7ML19985AB01 OCM OCM Variable condition FixedUnits OCM ‘U’ Parameters for P3 Primary Element OCM Reference U0 = exponent U1 = k factor P4 = 0 only= constant factor U1 = head Typical Weir Profiles Typical SHARP-CRESTED WeirsKhafagi Venturi Typical Parshall Flume Typical Leopold Lagco ‘U’ parameters required ‘U’ parameters calculated BS-3680 Rectangular Flume = crest width = Cv = crest height = Cd = crest length = a BS-3680 Round Nose Horizontal Crest Weir ¤ Refer to Operation \ Flow Calculation 7ML19985AB01 Cv = velocity coefficientBS-3680 Trapezoidal Flume BS-3680 U-Flume, P3 = BS-3680 U-FLUME = head H and p applied to C = crest width = C = crest height = Cp = crest lengthBS-3680 Finite Crest Weir = crest width He = effective head h + Kh = head Kh = 1 mm = Ce x 2⁄3 ⎯⎯√2⎯g x be x he1.5 Where q = flow rate= approach width = Ce = crest width = K b = crest height = gravitational accelerationBS-3680 Thin Plate Rectangular Weir U0 = notch angle Alpha U1 = Ce BS-3680 Thin Plate V-NOTCH Weir U0 = crest width b Rectangular Weir Contracted = hydraulic radius = slope of hydraulic gradient Based on the Manning FormulaRound Pipe U0 = maximum flume width, hmax PALMER-BOWLUS Flume U0 = maximum listed head, hmax Flume U0 = number of data points n, 4 to Universal Head vs FLOW, P3 =Flow, point A19 Flow, point A13 Head, point A14Flow, point A15 Head, point A16 Flow, point A17 Head, point A18U0 = channel width B U1 = area h Rectangular Area X Velocity = head, cm = flow velocity, cm/sec Trapezoidal Area X Velocity For h ≥ d = B b/d Where q = flow rate, l/s= channel top width, cm = head, cm = channel base width, cm Modified Trapezoidal Area X Velocity U0 = base diameter D U1 = area h Channel Area x Velocity U0 = conduit diameter U1 = area h Circular Area X Velocity GULL-WING Area X VELOCITY, P3 = Gull Wing Area X Velocity EGG-SHAPED Area X VELOCITY, P3 = EGG-SHAPED Area X Velocity Typical open channel Universal Area X VELOCITY, P3 =Area Head Universal Area X VelocityA10 = OCM Maintenance Error Codes Computer Customer’s Serial printer 102 Protocol for the OCM-3 is as follows Baud rateRefer to Cvcc Instruction DB-9 connectorDB-25 connector Bipolar CurrentP35 = 7, print interval set for 7 minutes Date104 Remote OCM-3 display Local display Utilities Software Programmer Remote OCM-3 programming105 106 107 Typical OCM-3Display value 00.000000 99.12399.123000 7ML19985AB01Response # = 0 through Content of P5Stop data log down load Start data log down load109 Computer Telephone lines Remote modem DB-25 connector 7ML19985AB01Standard modem CableConnect Establishing Communication111 112 Ending CommunicationRev