ETA Systems ETA-ECM30 specifications Front Panel Features, Trigger/Status Port Pin Identification

Page 6

ETA-ECM30

30A AC Power Module Spike Suppressor

FRONT PANEL FEATURES

3 4 5

A

B

C

D

E

1

2

6

1. Trigger/Status Port Pin Identification

All signals are of low voltage and current. DO NOT MISS WIRE or damage may occur.

A.(+) requires a minimum of 5–24V DC to activate the module with 5mA of current. Note: The DCV can be supplied from any source. The EVS protection requires the ETA-ECS6RM for operation.

B.G = Circuit Ground. Must be of the same circuit as the DCV source.

C.V = AC Voltage Status Signal. Reports the Incoming AC Mains Voltage to the ECM module back to the ETA-ECS6RM.

D.NC = No Connection

E.D = Fault Status Signal. Reports any fault conditions of an ECM module to the ETA-ECS6RM.

2.External Trigger/Manual On Switch

The ETA-ECM30 has a manual override switch allowing it to be used as a local Spike Suppressor. For remote monitoring and activation, the switch must be in the “External Trigger” position.

3. Active LED

This LED will illuminate Green when the ECM module has sensed the proper DCV to activate the unit. Note: If the ETA-ECM30 is connected to the ETA-ECS6RM and the EVS circuit has been activated, this LED will not be lit. The Channel Status LED on the ETA-ECS6RM will flash indicating a problem and the ECM module will not turn On until the AC Mains voltage is stable.

4. AC Fault LED

If damage to the Spike Suppression circuit occurs, this LED will illuminate Red. The module may still operate but may not be protecting the items plugged into the AC outlets. The ECM module should be inspected and repaired by a qualified technician.

5. Incoming AC LED

This LED will illuminate Red when the ECM has incoming AC power present at the module. This LED must be On to operate. Note: If this LED is not illuminating check the following: 1) the unit is plugged in, 2) the AC Mains Breaker feeding the AC leg to the ECM module is Off, 3) the internal fuse has been damaged. This should only be inspected by an authorized technician.

6.AC Mains Outlet

120V 30A L5-30 Receptacle

1601 Jack McKay Blvd. • Ennis, Texas 75119 U.S.A.

Telephone: 800-321-6699 • Fax: 800-996-3821

– 6 –

ETAsys.com

Specifications are subject to change without notice.

Page 5 Page 7
Image 6
Page 5 Page 7
Contents ETA-ECM30 Table of Contents Important Safety Instructions ETA-ECM30 KEY Features IntroductionApplications Front Panel Features Trigger/Status Port Pin IdentificationECM Housing Types ECM-RACEWY1 ECM-RACEWY3 ECM-RACEWY6ECM Module Activation Without Using AN ETA-ECS6RM Controller Wiring the ETA-ECM30 Control Module ETA-ECM30 Specifications Front PanelETA-ECM30 Limited Warranty Service
Related manuals
Manual 1 pages 27.53 Kb

ETA-ECM30 specifications

The ETA Systems ETA-ECM30 is a cutting-edge energy management and monitoring solution designed for efficient power distribution and optimization across various applications. This advanced system is built to cater to the needs of both commercial and industrial settings, providing robust functionalities that ensure optimal energy utilization.

One of the standout features of the ETA-ECM30 is its real-time monitoring capability. The device continuously tracks energy consumption patterns, allowing users to make informed decisions to enhance efficiency and lower operational costs. The high-resolution display provides clear visual data, highlighting key metrics such as voltage, current, power factor, and total energy consumption. These metrics are crucial for identifying areas that require improvement.

Incorporating advanced communication technologies, the ETA-ECM30 supports various protocols including Modbus, Ethernet, and RS-485. This ensures seamless integration with existing infrastructure, facilitating remote monitoring and control. The ability to interact with other intelligent devices within an energy management system creates a cohesive network, enabling sophisticated automation and optimization strategies.

The ETA-ECM30 also boasts extensive data logging capabilities, archiving historical data that can be analyzed to identify trends over time. This functionality is essential for predictive maintenance and long-term planning, providing users with insights that can lead to significant operational improvements.

Safety and compliance are paramount in energy systems, and the ETA-ECM30 meets high standards in both areas. It features overload protection, surge suppression, and fault detection, ensuring the safety of both the equipment and users. Furthermore, it complies with industry regulations and standards, making it a reliable choice for discerning businesses.

User-friendliness is another essential aspect of the ETA-ECM30. The device is designed with an intuitive interface, making it accessible for users with varying levels of technical expertise. Easy navigation allows for quick setup and configuration, reducing the time and effort needed to get the system operational.

In summary, the ETA Systems ETA-ECM30 is an innovative energy management solution that combines real-time monitoring, advanced communication technologies, comprehensive data logging, and robust safety features. Its user-friendly design and high compatibility make it an ideal choice for businesses aiming to enhance their energy efficiency and reduce costs while complying with safety standards. Whether in a commercial or industrial environment, this system is equipped to deliver superior performance and reliability.
Top Page Image Contents